How to Customize Partitions

[中文]

This document describes how to customize the partitions in your ESP device by modifying the at_customize.csv table provided by ESP-AT. There are two partition tables: the primary partition and the secondary partition table.

The primary partition table partitions_at.csv is for system usage, based on which the partitions_at.bin file is generated. If the primary partition table goes wrong, the system will fail to startup. Therefore, it is not recommended to modify the partitions_at.csv.

ESP-AT provides a secondary partition table at_customize.csv that you can customize to store self-defined blocks of data. It is based on the primary partition table.

To modify the partition in your ESP device, please follow the first three steps. The fourth section illustrates the three steps with an example.

Modify at_customize.csv

Find the at_customize.csv for your module with reference to the following table.

at_customize.csv paths

Platform

Module

Paths

ESP32

  • WROOM-32

  • PICO-D4

  • SOLO-1

  • MINI-1

module_esp32_default/at_customize.csv

ESP32

WROVER-32

module_wrover-32/at_customize.csv

ESP32

ESP32-D2WD

module_esp32-d2wd/at_customize.csv

ESP32

ESP32_QCLOUD

module_esp32_qcloud/at_customize.csv

ESP32-C3

MINI-1

module_esp32c3_default/at_customize.csv

ESP32-C3

ESP32C3_QCLOUD

module_esp32c3_qcloud/at_customize.csv

Then, follow the rules below when modifying at_customize.csv.

  • Do not change the Name and Type of the user partitions that have already been defined in it, while SubType, Offset, and Size can be changed.

  • If you need to add a new user partition, please check if it has already been defined in the ESP-IDF (esp_partition.h) first.

    • If yes, you should keep the Type value the same as that of ESP-IDF.

    • If no, please set the Type to 0x40.

  • A user partition’s Name should not be longer than 16 bytes.

  • The default size of the entire at_customize partition is defined in the partitions_at.csv table. Please do not exceed the range when adding new user partitions.

Generate at_customize.bin

After having modified the at_customize.csv, you can either recompile the ESP-AT project to generate the at_customize.bin file, or use the python script gen_esp32part.py.

If you use the script, execute the following command under the root directory of ESP-AT project and replace INPUT and OUTPUT:

python esp-idf/components/partition_table/gen_esp32part.py <INPUT> [OUTPUT]
  • Replace INPUT with the path to at_customize.csv or the binary file to parse.

  • Replace OUTPUT with the path to output converted binary or CSV file. Stdout will be used if omitted.

Flash at_customize.bin into ESP Device

Download the at_customize.bin into flash. Please refer to Flash AT Firmware into Your Device for how to flash bin files into ESP and the following table for the download address for your module.

at_customize.bin download address of modules

Platform

Module

Address

Size

ESP32

  • WROOM-32

  • WROVER-32

  • PICO-D4

  • SOLO-1

  • MINI-1

  • ESP32-D2WD

  • ESP32_QCLOUD

0x20000

0xE0000

ESP32-C3

MINI-1

0x1E000

0x42000

ESP32-C3

ESP32C3_QCLOUD

0x20000

0xE0000

There are cases where at_customize.bin must be downloaded to flash in order to use certain AT commands:

Example

The section demonstrates how to add a 4 KB partition named test into the ESP32-WROOM-32 module.

Firstly, find the at_customize.csv table for ESP32-WROOM-32 and set the Name, Type, Subtype, Offset, and Size of the new partition:

# Name,Type,SubType,Offset,Size
... ...
test,0x40,15,0x3D000,4K
fatfs,data,fat,0x70000,576K

Secondly, recompile the ESP-AT project, or execute the python script in the ESP-AT root directory to generate at_customize.bin.

python esp-idf/components/partition_table/gen_esp32part.py -q ./module_config/module_esp32_default/at_customize.csv at_customize.bin

Then, the at_customize.bin will be generated in the ESP-AT root directory.

Thirdly, download the at_customize.bin to flash.

Execute the following command under the root directory of ESP-AT project and replace PORT and BAUD.

python esp-idf/components/esptool_py/esptool/esptool.py -p PORT -b BAUD --before default_reset --after hard_reset --chip auto  write_flash --flash_mode dio --flash_size detect --flash_freq 40m 0x20000 ./at_customize.bin
  • Replace PORT with your port name.

  • Replace BAUD with the baud rate.