ESP8684-DevKitM-1

[中文]

The latest version: ESP8684-DevKitM-1 v1.1.

This user guide will help you get started with ESP8684-DevKitM-1 and will also provide more in-depth information.

The ESP8684-DevKitM-1 is an entry-level development board based on ESP8684-MINI-1, a general-purpose module with 1 MB/2 MB/4 MB SPI flash. This board integrates complete Wi-Fi and Bluetooth LE functions.

Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP8684-DevKitM-1 on a breadboard.

ESP8684-DevKitM-1 with ESP8684-MINI-1 module

ESP8684-DevKitM-1 with ESP8684-MINI-1 module

The document consists of the following major sections:

Getting Started

This section provides a brief introduction of ESP8684-DevKitM-1, instructions on how to do the initial hardware setup and how to flash firmware onto it.

Description of Components

ESP8684-DevKitM-1 - front

ESP8684-DevKitM-1 - front

The key components of the board are described in a counter-clockwise direction.

Key Component

Description

ESP8684-MINI-1

ESP8684-MINI-1 from Espressif is a powerful and general-purpose module that offers Wi-Fi and Bluetooth LE coexistence. It has a PCB antenna and a 1 MB/2 MB/4 MB SPI flash.

5 V to 3.3 V LDO

Power regulator that converts a 5 V supply into a 3.3 V output.

5 V Power On LED

Turns on when the USB power is connected to the board.

Pin Headers

All available GPIO pins are broken out to the pin headers on the board. For details, please see Header Block.

Boot Button

Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.

Micro-USB Port

USB interface. Power supply for the board as well as the communication interface between a computer and the ESP8684 chip.

Reset Button

Press this button to restart the system.

USB-to-UART Bridge

Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.

RGB LED

Addressable RGB LED, driven by GPIO8.

Start Application Development

Before powering up your board, please make sure that it is in good condition with no obvious signs of damage.

Required Hardware

  • ESP8684-DevKitM-1

  • USB 2.0 cable (Standard-A to Micro-B)

  • Computer running Windows, Linux, or macOS

Note

Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.

Software Setup

Please proceed to Get Started, where Section Installation Step by Step will quickly help you set up the development environment then flash an application example onto your board.

ESP-AT Support

The ESP8684-DevKitM-1 supports ESP-AT software that provides a set of AT commands with which you can quickly integrate wireless connectivity features into your product without a need for embedded application development of the module on this development board.

The software is available as a pre-built binary that can be downloaded from ESP-AT repository.

For more information about using ESP-AT, including information on how to customize pre-built binaries, please refer to ESP-AT User Guide.

Contents and Packaging

Retail Orders

If you order a few samples, each board comes in an individual package in either antistatic bag or any packaging depending on your retailer.

For retail orders, please go to https://www.espressif.com/en/company/contact/buy-a-sample.

Wholesale Orders

If you order in bulk, the boards come in large cardboard boxes.

For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.

Hardware Overview

Block Diagram

The block diagram below shows the components of ESP8684-DevKitM-1 and their interconnections.

ESP8684-DevKitM-1 (click to enlarge)

ESP8684-DevKitM-1 (click to enlarge)

Power Supply Options

There are three mutually exclusive ways to provide power to the board:

  • Micro-USB Port, default power supply (recommended)

  • 5V and G (GND) pins

  • 3V3 and G (GND) pins

Header Block

The two tables below provide the Name and Function of the pins on both sides of the board (J1 and J3). The pin names are shown in ESP8684-DevKitM-1 - front. The numbering is the same as in the Board Schematic (PDF).

J1

No.

Name

Type 1

Function

1

G

G

Ground

2

3V3

P

3.3 V power supply

3

3V3

P

3.3 V power supply

4

2

I/O/T

GPIO2, ADC1_CH2, FSPIQ

5

3

I/O/T

GPIO3, ADC1_CH3

6

G

G

Ground

7

RST

I

Reset; High: enable; Low: powers off

8

G

G

Ground

9

0

I/O/T

GPIO0, ADC1_CH0

10

1

I/O/T

GPIO1, ADC1_CH1

11

10

I/O/T

GPIO10, FSPICS0

12

G

G

Ground

13

5V

P

5 V power supply

14

5V

P

5 V power supply

15

G

G

Ground

J3

No.

Name

Type 1

Function

1

G

G

Ground

2

TX

I/O/T

GPIO20, U0TXD

3

RX

I/O/T

GPIO19, U0RXD

4

G

G

Ground

5

9

I/O/T

GPIO9 2

6

8

I/O/T

GPIO8 2, RGB LED

7

G

G

Ground

8

7

I/O/T

GPIO7, FSPID , MTDO

9

6

I/O/T

GPIO6, FSPICLK , MTCK

10

5

I/O/T

GPIO5, ADC2_CH0, FSPIWP ,MTDI

11

4

I/O/T

GPIO4, ADC1_CH4, FSPIHD ,MTMS

12

G

G

Ground

13

18

I/O/T

GPIO18

14

G

G

Ground

15

G

G

Ground

1(1,2)

P: Power supply; I: Input; O: Output; T: High impedance.

2(1,2)

GPIO8 and GPIO9 are strapping pins of the ESP8684 chip. These pins are used to control several chip functions depending on binary voltage values applied to the pins during chip power-up or system reset.

Pin Layout

ESP8684-DevKitM-1 (click to enlarge)

ESP8684-DevKitM-1 Pin Layout (click to enlarge)

Hardware Revision Details

This is the first revision of this board released.