HCI Vendor-specific (VS) Commands

[中文]

HCI VS Commands for Espressif's Bluetooth Host

The following HCI VS commands are exclusively for Espressif's Bluetooth Host (ESP-Bluedroid Host or ESP-NimBLE Host). If you are using a non-ESP host or HCI UART, these commands will remain disabled unless the initialization function is explicitly called from the application. Note, these init functions as well as these additional HCI VS commands are intended for Espressif's Bluetooth Host use only. Application developers should not call the init functions in their applications.

ESP_BT_VS_COMMON_ECHO_OCF

Test vendor HCI feature (OCF: 0x0081)

The Controller returns the value in command.

Note

The init function is bt_stack_enableEchoVsCmd(true)

ESP_BT_VS_CONFIG_DUP_EXC_LIST_OCF

Config scanning duplicate exceptional list (OCF: 0x0108)

Note

The init function is advFilter_stack_eanbleDupExcListCmd(true)

ESP_BT_VS_SET_ADV_REPORT_FLOW_CTRL_OCF

Enable/disable advertising report flow control (OCF: 0x0109)

Note

The init function is scan_stack_enableAdvFlowCtrlVsCmd(true)

ESP_BT_VS_UPD_ADV_REPORT_FLOW_CTRL_NUM_OCF

Update the number of advertising report in ADV flow control (OCF: 0x010A)

Note

The init function is scan_stack_enableAdvFlowCtrlVsCmd(true)

ESP_BT_VS_CLR_LEGACY_ADV_OCF

Clear legacy advertising (same as HCI_LE_Clear_Advertising_Sets) (OCF: 0x010C)

Note

The init function is adv_stack_enableClearLegacyAdvVsCmd(true)

ESP_BT_VS_ENABLE_CSA2_OCF

Enable/disable channel selection algorithm #2 (OCF: 0x0112)

Note

The init function is chanSel_stack_enableSetCsaVsCmd(true)

HCI VS Events for Espressif's Bluetooth Host

The following HCI VS events are exclusively for Espressif's Bluetooth Host (ESP-Bluedroid Host or ESP-NimBLE Host). If you are using a non-ESP host or HCI UART, these events will remain disabled unless the initialization function is explicitly called from the application. Note, these init functions as well as these additional HCI VS events are intended for Espressif's Bluetooth Host use only. Application developers should not call the init functions in their applications.

ESP_BT_VS_LE_ADV_LOST_EVT_SUBCODE

BLE advertising report lost event for flow control (EVTCODE: 0x3E, SUBCODE: 0xF0)

Note

The init function is scan_stack_enableAdvFlowCtrlVsCmd(true)

HCI VS Commands for Espressif's Internal-Use Debugging

The following HCI VS debugging commands are implemented in Bluetooth Low Energy controller pre-compiled libraries. These commands are not linked into the application binary, unless the function esp_ble_internalTestFeaturesEnable(true) is called from the application. They are intended for Espressif's internal use only. Application developers should not call esp_ble_internalTestFeaturesEnable(true) in their applications.

ESP_BT_VS_CFG_TEST_ENABLE_SUBCMD
ESP_BT_VS_CFG_TEST_ENABLE_ADV_DELAY_SUBCMD
ESP_BT_VS_CFG_TEST_SET_PREF_CODED_SUBCMD
ESP_BT_VS_CFG_TEST_SET_DEFAULT_PRIV_MODE_SUBCMD
ESP_BT_VS_CFG_TEST_SET_SCAN_FOREVER_SUBCMD
ESP_BT_VS_CFG_TEST_SET_EXPECTED_PEER_SUBCMD
ESP_BT_VS_CFG_TEST_GET_ADV_TXED_CNT_SUBCMD
ESP_BT_VS_CFG_TEST_GET_SCAN_RXED_CNT_SUBCMD
ESP_BT_VS_CFG_TEST_SET_TXPWR_LVL_SUBCMD
ESP_BT_VS_CFG_TEST_GET_TXPWR_LVL_SUBCMD
ESP_BT_VS_CFG_TEST_SET_TXPWR_LVL_ENH_SUBCMD
ESP_BT_VS_CFG_TEST_GET_TXPWR_LVL_ENH_SUBCMD
ESP_BT_VS_CFG_TEST_ENABLE_CCA_SUBCMD
ESP_BT_VS_CFG_TEST_CLEAR_RAND_ADDR_SUBCMD
ESP_BT_VS_CFG_TEST_GET_MAX_TXPWR_SUBCMD
ESP_BT_VS_CFG_TEST_GET_TXPWR_RANGE_SUBCMD
ESP_BT_VS_CFG_TEST_SET_SCAN_AA_SUBCMD
ESP_BT_VS_CFG_TEST_SET_ADV_AA_SUBCMD
ESP_BT_VS_CFG_TEST_SET_SCAN_CHAN_SUBCMD
ESP_BT_VS_CFG_TEST_GET_CTRL_STATUS_SUBCMD
ESP_BT_VS_CFG_TEST_GET_CTRL_COMPILE_VER_SUBCMD
ESP_BT_VS_CFG_TEST_SET_AUX_ADV_OFFSET_SUBCMD
ESP_BT_VS_CFG_TEST_SET_AUX_OFFSET_THRESHOLD_SUBCMD

Was this page helpful?