Dedicated GPIO

Overview

The dedicated GPIO is designed for CPU interaction with GPIO matrix and IO MUX. Any GPIO that is configured as “dedicated” can be access by CPU instructions directly, which makes it easy to achieve a high GPIO flip speed, and simulate serial/parallel interface in a bit-banging way. As toggling a GPIO in this “CPU Dedicated” way costs few overhead, it would be great for cases like performance measurement using an oscilloscope.

Create/Destroy GPIO Bundle

A GPIO bundle is a group of GPIOs, which can be manipulated at the same time in one CPU cycle. The maximal number of GPIOs that a bundle can contain is limited by each CPU. What’s more, the GPIO bundle has a strong relevance to the CPU which it derives from. Any operations on the GPIO bundle should be put inside a task which is running on the same CPU core to the GPIO bundle belongs to. Likewise, only those ISRs who are installed on the same CPU core are allowed to do operations on that GPIO bundle.

Note

Dedicated GPIO is more of a CPU peripheral, so it has a strong relationship with CPU core. It’s highly recommended to install and operate GPIO bundle in a pin-to-core task. For example, if GPIOA is connected to CPU0, and the dedicated GPIO instruction is issued from CPU1, then it’s impossible to control GPIOA.

To install a GPIO bundle, one needs to call dedic_gpio_new_bundle() to allocate the software resources and connect the dedicated channels to user selected GPIOs. Configurations for a GPIO bundle are covered in dedic_gpio_bundle_config_t structure:

  • gpio_array: An array that contains GPIO number.

  • array_size: Element number of gpio_array.

  • flags: Extra flags to control the behavior of GPIO Bundle.

    • in_en and out_en are used to select whether to enable the input and output function (note, they can be enabled together).

    • in_invert and out_invert are used to select whether to invert the GPIO signal.

The following code shows how to install a output only GPIO bundle:

// configure GPIO
const int bundleA_gpios[] = {0, 1};
gpio_config_t io_conf = {
    .mode = GPIO_MODE_OUTPUT,
};
for (int i = 0; i < sizeof(bundleA_gpios) / sizeof(bundleA_gpios[0]); i++) {
    io_conf.pin_bit_mask = 1ULL << bundleA_gpios[i];
    gpio_config(&io_conf);
}
// Create bundleA, output only
dedic_gpio_bundle_handle_t bundleA = NULL;
dedic_gpio_bundle_config_t bundleA_config = {
    .gpio_array = bundleA_gpios,
    .array_size = sizeof(bundleA_gpios) / sizeof(bundleA_gpios[0]),
    .flags = {
        .out_en = 1,
    },
};
ESP_ERROR_CHECK(dedic_gpio_new_bundle(&bundleA_config, &bundleA));

To uninstall the GPIO bundle, one needs to call dedic_gpio_del_bundle().

Note

dedic_gpio_new_bundle() doesn’t cover any GPIO pad configuration (e.g. pull up/down, drive ability, output/input enable), so before installing a dedicated GPIO bundle, you have to configure the GPIO separately using GPIO driver API (e.g. gpio_config()). For more information about GPIO driver, please refer to GPIO API Reference.

GPIO Bundle Operations

Operations

Functions

Write to GPIOs in the bundle by mask

dedic_gpio_bundle_write()

Read the value that input to bundle

dedic_gpio_bundle_read_out()

Read the value that output from bundle

dedic_gpio_bundle_read_in()

Note

The functions above just wrap the customized instructions defined for ESP32-S2, for the details of those instructions, please refer to ESP32-S2 Technical Reference Manual > IO MUX and GPIO Matrix (GPIO, IO_MUX) [PDF].

Interrupt Handling

Dedicated GPIO can also trigger interrupt on specific input event. All supported events are defined in dedic_gpio_intr_type_t.

One can enable and register interrupt callback by calling dedic_gpio_bundle_set_interrupt_and_callback(). The prototype of the callback function is defined in dedic_gpio_isr_callback_t. Keep in mind, the callback should return true if there’s some high priority task woken up.

// user defined ISR callback
IRAM_ATTR bool dedic_gpio_isr_callback(dedic_gpio_bundle_handle_t bundle, uint32_t index, void *args)
{
    SemaphoreHandle_t sem = (SemaphoreHandle_t)args;
    BaseType_t high_task_wakeup = pdFALSE;
    xSemaphoreGiveFromISR(sem, &high_task_wakeup);
    return high_task_wakeup == pdTRUE;
}

// enable positive edge interrupt on the second GPIO in the bundle (i.e. index 1)
ESP_ERROR_CHECK(dedic_gpio_bundle_set_interrupt_and_callback(bundle, BIT(1), DEDIC_GPIO_INTR_POS_EDGE, dedic_gpio_isr_callback, sem));

// wait for done semaphore
xSemaphoreTake(sem, portMAX_DELAY);

Manipulate GPIOs by Writing Assembly Code

For advanced users, they can always manipulate the GPIOs by writing assembly code or invoking CPU Low Level APIs. The usual procedure could be:

  1. Allocate a GPIO bundle: dedic_gpio_new_bundle()

  2. Query the mask occupied by that bundle: dedic_gpio_get_out_mask() or/and dedic_gpio_get_in_mask()

  3. Call CPU LL apis (e.g. cpu_ll_write_dedic_gpio_mask) or write assembly code with that mask

  4. The fasted way of toggling IO is to use the dedicated “set/clear” instructions:

CPU Arch

Set bits of GPIO

Clear bits of GPIO

Remarks

Xtensa

set_bit_gpio_out imm[7:0]

clr_bit_gpio_out imm[7:0]

immediate value width depends on the number of dedicated GPIO channels

RISC-V

csrrsi rd, csr, imm[4:0]

csrrci rd, csr, imm[4:0]

can only control the lowest 4 GPIO channels

For details of supported dedicated GPIO instructions, please refer to ESP32-S2 Technical Reference Manual > IO MUX and GPIO Matrix (GPIO, IO_MUX) [PDF]. The supported dedicated CPU instructions are also wrapped inside soc/cpu_ll.h as helper inline functions.

Note

Writing assembly code in application could make your code hard to port between targets, because those customized instructions are not guaranteed to remain the same format on different targets.

Application Example

Matrix keyboard example based on dedicated GPIO: peripherals/gpio/matrix_keyboard.

API Reference

Functions

esp_err_t dedic_gpio_get_out_mask(dedic_gpio_bundle_handle_t bundle, uint32_t *mask)

Get allocated channel mask.

Note

Each bundle should have at least one mask (in or/and out), based on bundle configuration.

Note

With the returned mask, user can directly invoke LL function like “cpu_ll_write_dedic_gpio_mask” or write assembly code with dedicated GPIO instructions, to get better performance on GPIO manipulation.

Parameters
  • bundle[in] Handle of GPIO bundle that returned from “dedic_gpio_new_bundle”

  • mask[out] Returned mask value for on specific direction (in or out)

Returns

  • ESP_OK: Get channel mask successfully

  • ESP_ERR_INVALID_ARG: Get channel mask failed because of invalid argument

  • ESP_FAIL: Get channel mask failed because of other error

esp_err_t dedic_gpio_get_in_mask(dedic_gpio_bundle_handle_t bundle, uint32_t *mask)
esp_err_t dedic_gpio_new_bundle(const dedic_gpio_bundle_config_t *config, dedic_gpio_bundle_handle_t *ret_bundle)

Create GPIO bundle and return the handle.

Note

One has to enable at least input or output mode in “config” parameter.

Parameters
  • config[in] Configuration of GPIO bundle

  • ret_bundle[out] Returned handle of the new created GPIO bundle

Returns

  • ESP_OK: Create GPIO bundle successfully

  • ESP_ERR_INVALID_ARG: Create GPIO bundle failed because of invalid argument

  • ESP_ERR_NO_MEM: Create GPIO bundle failed because of no capable memory

  • ESP_ERR_NOT_FOUND: Create GPIO bundle failed because of no enough continuous dedicated channels

  • ESP_FAIL: Create GPIO bundle failed because of other error

esp_err_t dedic_gpio_del_bundle(dedic_gpio_bundle_handle_t bundle)

Destory GPIO bundle.

Parameters

bundle[in] Handle of GPIO bundle that returned from “dedic_gpio_new_bundle”

Returns

  • ESP_OK: Destory GPIO bundle successfully

  • ESP_ERR_INVALID_ARG: Destory GPIO bundle failed because of invalid argument

  • ESP_FAIL: Destory GPIO bundle failed because of other error

void dedic_gpio_bundle_write(dedic_gpio_bundle_handle_t bundle, uint32_t mask, uint32_t value)

Write value to GPIO bundle.

Note

The mask is seen from the view of GPIO bundle. For example, bundleA contains [GPIO10, GPIO12, GPIO17], to set GPIO17 individually, the mask should be 0x04.

Note

For performance reasons, this function doesn’t check the validity of any parameters, and is placed in IRAM.

Parameters
  • bundle[in] Handle of GPIO bundle that returned from “dedic_gpio_new_bundle”

  • mask[in] Mask of the GPIOs to be written in the given bundle

  • value[in] Value to write to given GPIO bundle, low bit represents low member in the bundle

uint32_t dedic_gpio_bundle_read_out(dedic_gpio_bundle_handle_t bundle)

Read the value that output from the given GPIO bundle.

Note

For performance reasons, this function doesn’t check the validity of any parameters, and is placed in IRAM.

Parameters

bundle[in] Handle of GPIO bundle that returned from “dedic_gpio_new_bundle”

Returns

Value that output from the GPIO bundle, low bit represents low member in the bundle

uint32_t dedic_gpio_bundle_read_in(dedic_gpio_bundle_handle_t bundle)

Read the value that input to the given GPIO bundle.

Note

For performance reasons, this function doesn’t check the validity of any parameters, and is placed in IRAM.

Parameters

bundle[in] Handle of GPIO bundle that returned from “dedic_gpio_new_bundle”

Returns

Value that input to the GPIO bundle, low bit represents low member in the bundle

esp_err_t dedic_gpio_bundle_set_interrupt_and_callback(dedic_gpio_bundle_handle_t bundle, uint32_t mask, dedic_gpio_intr_type_t intr_type, dedic_gpio_isr_callback_t cb_isr, void *cb_args)

Set interrupt and callback function for GPIO bundle.

Note

This function is only valid for bundle with input mode enabled. See “dedic_gpio_bundle_config_t”

Note

The mask is seen from the view of GPIO Bundle. For example, bundleA contains [GPIO10, GPIO12, GPIO17], to set GPIO17 individually, the mask should be 0x04.

Parameters
  • bundle[in] Handle of GPIO bundle that returned from “dedic_gpio_new_bundle”

  • mask[in] Mask of the GPIOs in the given bundle

  • intr_type[in] Interrupt type, set to DEDIC_GPIO_INTR_NONE can disable interrupt

  • cb_isr[in] Callback function, which got invoked in ISR context. A NULL pointer here will bypass the callback

  • cb_args[in] User defined argument to be passed to the callback function

Returns

  • ESP_OK: Set GPIO interrupt and callback function successfully

  • ESP_ERR_INVALID_ARG: Set GPIO interrupt and callback function failed because of invalid argument

  • ESP_FAIL: Set GPIO interrupt and callback function failed because of other error

Structures

struct dedic_gpio_bundle_config_t

Type of Dedicated GPIO bundle configuration.

Public Members

const int *gpio_array

Array of GPIO numbers, gpio_array[0] ~ gpio_array[size-1] <=> low_dedic_channel_num ~ high_dedic_channel_num

size_t array_size

Number of GPIOs in gpio_array

unsigned int in_en

Enable input

unsigned int in_invert

Invert input signal

unsigned int out_en

Enable output

unsigned int out_invert

Invert output signal

struct dedic_gpio_bundle_config_t::[anonymous] flags

Flags to control specific behaviour of GPIO bundle

Type Definitions

typedef struct dedic_gpio_bundle_t *dedic_gpio_bundle_handle_t

Type of Dedicated GPIO bundle.

typedef bool (*dedic_gpio_isr_callback_t)(dedic_gpio_bundle_handle_t bundle, uint32_t index, void *args)

Type of dedicated GPIO ISR callback function.

Param bundle

Handle of GPIO bundle that returned from “dedic_gpio_new_bundle”

Param index

Index of the GPIO in its corresponding bundle (count from 0)

Param args

User defined arguments for the callback function. It’s passed through dedic_gpio_bundle_set_interrupt_and_callback

Return

If a high priority task is woken up by the callback function

Enumerations

enum dedic_gpio_intr_type_t

Supported type of dedicated GPIO interrupt.

Values:

enumerator DEDIC_GPIO_INTR_NONE

No interrupt

enumerator DEDIC_GPIO_INTR_LOW_LEVEL

Interrupt on low level

enumerator DEDIC_GPIO_INTR_HIGH_LEVEL

Interrupt on high level

enumerator DEDIC_GPIO_INTR_NEG_EDGE

Interrupt on negedge

enumerator DEDIC_GPIO_INTR_POS_EDGE

Interrupt on posedge

enumerator DEDIC_GPIO_INTR_BOTH_EDGE

Interrupt on both negedge and posedge