GPIO & RTC GPIO

[English]

GPIO 汇总

ESP32-S2 芯片具有 43 个物理 GPIO 管脚（GPIO0 ~ GPIO21 和 GPIO26 ~ GPIO46）。每个管脚都可用作一个通用 IO，或连接一个内部的外设信号。通过 IO MUX、RTC IO MUX 和 GPIO 交换矩阵，可配置外设模块的输入信号来源于任何的 IO 管脚，并且外设模块的输出信号也可连接到任意 IO 管脚。这些模块共同组成了芯片的 IO 控制。更多详细信息，请参阅 ESP32-S2 技术参考手册 > IO MUX 和 GPIO 矩阵（GPIO、IO_MUX） [PDF]。

下表提供了各管脚的详细信息，部分 GPIO 具有特殊的使用限制，具体可参考表中的注释列。

GPIO	模拟功能	RTC GPIO	注释
GPIO0		RTC_GPIO0	Strapping 管脚
GPIO1	ADC1_CH0	RTC_GPIO1
GPIO2	ADC1_CH1	RTC_GPIO2
GPIO3	ADC1_CH2	RTC_GPIO3
GPIO4	ADC1_CH3	RTC_GPIO4
GPIO5	ADC1_CH4	RTC_GPIO5
GPIO6	ADC1_CH5	RTC_GPIO6
GPIO7	ADC1_CH6	RTC_GPIO7
GPIO8	ADC1_CH7	RTC_GPIO8
GPIO9	ADC1_CH8	RTC_GPIO9
GPIO10	ADC1_CH9	RTC_GPIO10
GPIO11	ADC2_CH0	RTC_GPIO11
GPIO12	ADC2_CH1	RTC_GPIO12
GPIO13	ADC2_CH2	RTC_GPIO13
GPIO14	ADC2_CH3	RTC_GPIO14
GPIO15	ADC2_CH4	RTC_GPIO15
GPIO16	ADC2_CH5	RTC_GPIO16
GPIO17	ADC2_CH6	RTC_GPIO17
GPIO18	ADC2_CH7	RTC_GPIO18
GPIO19	ADC2_CH8	RTC_GPIO19
GPIO20	ADC2_CH9	RTC_GPIO20
GPIO21		RTC_GPIO21
GPIO26			SPI0/1
GPIO27			SPI0/1
GPIO28			SPI0/1
GPIO29			SPI0/1
GPIO30			SPI0/1
GPIO31			SPI0/1
GPIO32			SPI0/1
GPIO33
GPIO34
GPIO35
GPIO36
GPIO37
GPIO38
GPIO39			JTAG
GPIO40			JTAG
GPIO41			JTAG
GPIO42			JTAG
GPIO43
GPIO44
GPIO45			Strapping 管脚
GPIO46			GPI；Strapping 管脚

备注

• Strapping 管脚：GPIO0、GPIO45、和 GPIO46 是 Strapping 管脚。更多信息请参考 ESP32-S2 技术规格书。

• SPI0/1：GPIO26-32 通常用于 SPI flash 和 PSRAM，不推荐用于其他用途。

• JTAG：GPIO39-42 通常用于在线调试。

• GPI：GPIO46 固定为下拉，只能设置为输入模式。

GPIO 驱动提供了一个函数 gpio_dump_io_configuration() 用来输出指定管脚的实时配置状态，包括上下拉、输入输出使能、管脚映射等。输出示例如下：

================IO DUMP Start================
IO[4] -
  Pullup: 1, Pulldown: 0, DriveCap: 2
  InputEn: 1, OutputEn: 0, OpenDrain: 0
  FuncSel: 1 (GPIO)
  GPIO Matrix SigIn ID: (simple GPIO input)
  SleepSelEn: 1

IO[18] -
  Pullup: 0, Pulldown: 0, DriveCap: 2
  InputEn: 0, OutputEn: 1, OpenDrain: 0
  FuncSel: 1 (GPIO)
  GPIO Matrix SigOut ID: 256 (simple GPIO output)
  SleepSelEn: 1

IO[26] **RESERVED** -
  Pullup: 1, Pulldown: 0, DriveCap: 2
  InputEn: 1, OutputEn: 0, OpenDrain: 0
  FuncSel: 0 (IOMUX)
  SleepSelEn: 1

=================IO DUMP End==================

当 IO 管脚是通过 GPIO 交换矩阵连接到内部外设信号，输出信息打印中的外设信号 ID 定义可以在 soc/gpio_sig_map.h 文件中查看。**RESERVED** 字样则表示此 IO 被用于连接 FLASH 或 PSRAM，因此该引脚不应该被其他任何应用场景所征用并进行重新配置。

当 GPIO 连接到 RTC 低功耗和模拟子系统时，ESP32-S2 芯片还单独支持 RTC GPIO。可在以下情况时使用这些管脚功能：

• 处于 Deep-sleep 模式时

• 超低功耗协处理器 (ULP) 运行时

• 使用 ADC/DAC 等模拟功能时

GPIO 毛刺过滤器

ESP32-S2 内置硬件的过滤器可以过滤掉 GPIO 输入端口上的毛刺信号，在一定程度上避免错误触发中断或者是错把噪声当成有效的外设信号。

每个 GPIO 都可以使用独立的毛刺过滤器，该过滤器可以将那些脉冲宽度窄于 2 个采样时钟的信号剔除掉，该宽度无法配置。GPIO 对输入信号的采样时钟通常是 IO_MUX 的时钟源。在驱动中，此类过滤器称为 管脚毛刺过滤器。可以调用 gpio_new_pin_glitch_filter() 函数创建一个过滤器句柄。过滤器的相关配置保存在 gpio_pin_glitch_filter_config_t 结构体中。

• gpio_pin_glitch_filter_config_t::gpio_num 设置启用毛刺过滤器的 GPIO 编号。

毛刺过滤器默认关闭，可调用 gpio_glitch_filter_enable() 使能过滤器。如需回收这个过滤器，可以调用 gpio_del_glitch_filter() 函数。在回收句柄前，请确保过滤器处于关闭状态，否则需调用 gpio_glitch_filter_disable()。

应用示例

• GPIO 输出和输入中断示例：peripherals/gpio/generic_gpio。

API 参考 - 普通 GPIO

Header File

• components/driver/gpio/include/driver/gpio.h

Functions

esp_err_t gpio_config(const gpio_config_t *pGPIOConfig)

GPIO common configuration.

   Configure GPIO's Mode,pull-up,PullDown,IntrType

参数

pGPIOConfig -- Pointer to GPIO configure struct

返回

• ESP_OK success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_reset_pin(gpio_num_t gpio_num)

Reset an gpio to default state (select gpio function, enable pullup and disable input and output).

备注

This function also configures the IOMUX for this pin to the GPIO function, and disconnects any other peripheral output configured via GPIO Matrix.

参数

gpio_num -- GPIO number.

返回

Always return ESP_OK.

esp_err_t gpio_set_intr_type(gpio_num_t gpio_num, gpio_int_type_t intr_type)

GPIO set interrupt trigger type.

参数

• gpio_num -- GPIO number. If you want to set the trigger type of e.g. of GPIO16, gpio_num should be GPIO_NUM_16 (16);

• intr_type -- Interrupt type, select from gpio_int_type_t

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_intr_enable(gpio_num_t gpio_num)

Enable GPIO module interrupt signal.

备注

ESP32: Please do not use the interrupt of GPIO36 and GPIO39 when using ADC or Wi-Fi and Bluetooth with sleep mode enabled. Please refer to the comments of adc1_get_raw. Please refer to Section 3.11 of ESP32 ECO and Workarounds for Bugs for the description of this issue.

参数

gpio_num -- GPIO number. If you want to enable an interrupt on e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_intr_disable(gpio_num_t gpio_num)

Disable GPIO module interrupt signal.

备注

This function is allowed to be executed when Cache is disabled within ISR context, by enabling CONFIG_GPIO_CTRL_FUNC_IN_IRAM

参数

gpio_num -- GPIO number. If you want to disable the interrupt of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);

返回

• ESP_OK success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_set_level(gpio_num_t gpio_num, uint32_t level)

GPIO set output level.

备注

This function is allowed to be executed when Cache is disabled within ISR context, by enabling CONFIG_GPIO_CTRL_FUNC_IN_IRAM

参数

• gpio_num -- GPIO number. If you want to set the output level of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);

• level -- Output level. 0: low ; 1: high

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO number error

int gpio_get_level(gpio_num_t gpio_num)

GPIO get input level.

警告

If the pad is not configured for input (or input and output) the returned value is always 0.

参数

gpio_num -- GPIO number. If you want to get the logic level of e.g. pin GPIO16, gpio_num should be GPIO_NUM_16 (16);

返回

• 0 the GPIO input level is 0

• 1 the GPIO input level is 1

esp_err_t gpio_set_direction(gpio_num_t gpio_num, gpio_mode_t mode)

GPIO set direction.

Configure GPIO direction,such as output_only,input_only,output_and_input

参数

• gpio_num -- Configure GPIO pins number, it should be GPIO number. If you want to set direction of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);

• mode -- GPIO direction

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO error

esp_err_t gpio_set_pull_mode(gpio_num_t gpio_num, gpio_pull_mode_t pull)

Configure GPIO pull-up/pull-down resistors.

备注

ESP32: Only pins that support both input & output have integrated pull-up and pull-down resistors. Input-only GPIOs 34-39 do not.

参数

• gpio_num -- GPIO number. If you want to set pull up or down mode for e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);

• pull -- GPIO pull up/down mode.

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG : Parameter error

esp_err_t gpio_wakeup_enable(gpio_num_t gpio_num, gpio_int_type_t intr_type)

Enable GPIO wake-up function.

参数

• gpio_num -- GPIO number.

• intr_type -- GPIO wake-up type. Only GPIO_INTR_LOW_LEVEL or GPIO_INTR_HIGH_LEVEL can be used.

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_wakeup_disable(gpio_num_t gpio_num)

Disable GPIO wake-up function.

参数

gpio_num -- GPIO number

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_isr_register(void (*fn)(void*), void *arg, int intr_alloc_flags, gpio_isr_handle_t *handle)

Register GPIO interrupt handler, the handler is an ISR. The handler will be attached to the same CPU core that this function is running on.

This ISR function is called whenever any GPIO interrupt occurs. See the alternative gpio_install_isr_service() and gpio_isr_handler_add() API in order to have the driver support per-GPIO ISRs.

To disable or remove the ISR, pass the returned handle to the interrupt allocation functions.

参数

• fn -- Interrupt handler function.

• arg -- Parameter for handler function

• intr_alloc_flags -- Flags used to allocate the interrupt. One or multiple (ORred) ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info.

• handle -- Pointer to return handle. If non-NULL, a handle for the interrupt will be returned here.

返回

• ESP_OK Success ;

• ESP_ERR_INVALID_ARG GPIO error

• ESP_ERR_NOT_FOUND No free interrupt found with the specified flags

esp_err_t gpio_pullup_en(gpio_num_t gpio_num)

Enable pull-up on GPIO.

参数

gpio_num -- GPIO number

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_pullup_dis(gpio_num_t gpio_num)

Disable pull-up on GPIO.

参数

gpio_num -- GPIO number

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_pulldown_en(gpio_num_t gpio_num)

Enable pull-down on GPIO.

参数

gpio_num -- GPIO number

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_pulldown_dis(gpio_num_t gpio_num)

Disable pull-down on GPIO.

参数

gpio_num -- GPIO number

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_install_isr_service(int intr_alloc_flags)

Install the GPIO driver's ETS_GPIO_INTR_SOURCE ISR handler service, which allows per-pin GPIO interrupt handlers.

This function is incompatible with gpio_isr_register() - if that function is used, a single global ISR is registered for all GPIO interrupts. If this function is used, the ISR service provides a global GPIO ISR and individual pin handlers are registered via the gpio_isr_handler_add() function.

参数

intr_alloc_flags -- Flags used to allocate the interrupt. One or multiple (ORred) ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info.

返回

• ESP_OK Success

• ESP_ERR_NO_MEM No memory to install this service

• ESP_ERR_INVALID_STATE ISR service already installed.

• ESP_ERR_NOT_FOUND No free interrupt found with the specified flags

• ESP_ERR_INVALID_ARG GPIO error

void gpio_uninstall_isr_service(void)

Uninstall the driver's GPIO ISR service, freeing related resources.

esp_err_t gpio_isr_handler_add(gpio_num_t gpio_num, gpio_isr_t isr_handler, void *args)

Add ISR handler for the corresponding GPIO pin.

Call this function after using gpio_install_isr_service() to install the driver's GPIO ISR handler service.

The pin ISR handlers no longer need to be declared with IRAM_ATTR, unless you pass the ESP_INTR_FLAG_IRAM flag when allocating the ISR in gpio_install_isr_service().

This ISR handler will be called from an ISR. So there is a stack size limit (configurable as "ISR stack size" in menuconfig). This limit is smaller compared to a global GPIO interrupt handler due to the additional level of indirection.

参数

• gpio_num -- GPIO number

• isr_handler -- ISR handler function for the corresponding GPIO number.

• args -- parameter for ISR handler.

返回

• ESP_OK Success

• ESP_ERR_INVALID_STATE Wrong state, the ISR service has not been initialized.

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_isr_handler_remove(gpio_num_t gpio_num)

Remove ISR handler for the corresponding GPIO pin.

参数

gpio_num -- GPIO number

返回

• ESP_OK Success

• ESP_ERR_INVALID_STATE Wrong state, the ISR service has not been initialized.

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_set_drive_capability(gpio_num_t gpio_num, gpio_drive_cap_t strength)

Set GPIO pad drive capability.

参数

• gpio_num -- GPIO number, only support output GPIOs

• strength -- Drive capability of the pad

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_get_drive_capability(gpio_num_t gpio_num, gpio_drive_cap_t *strength)

Get GPIO pad drive capability.

参数

• gpio_num -- GPIO number, only support output GPIOs

• strength -- Pointer to accept drive capability of the pad

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t gpio_hold_en(gpio_num_t gpio_num)

Enable gpio pad hold function.

When a GPIO is set to hold, its state is latched at that moment and will not change when the internal signal or the IO MUX/GPIO configuration is modified (including input enable, output enable, output value, function, and drive strength values). This function can be used to retain the state of GPIOs when the power domain of where GPIO/IOMUX belongs to becomes off. For example, chip or system is reset (e.g. watchdog time-out, deep-sleep events are triggered), or peripheral power-down in light-sleep.

This function works in both input and output modes, and only applicable to output-capable GPIOs. If this function is enabled: in output mode: the output level of the GPIO will be locked and can not be changed. in input mode: the input read value can still reflect the changes of the input signal.

However, on ESP32/S2/C3/S3/C2, this function cannot be used to hold the state of a digital GPIO during Deep-sleep. Even if this function is enabled, the digital GPIO will be reset to its default state when the chip wakes up from Deep-sleep. If you want to hold the state of a digital GPIO during Deep-sleep, please call gpio_deep_sleep_hold_en.

Power down or call gpio_hold_dis will disable this function.

参数

gpio_num -- GPIO number, only support output-capable GPIOs

返回

• ESP_OK Success

• ESP_ERR_NOT_SUPPORTED Not support pad hold function

esp_err_t gpio_hold_dis(gpio_num_t gpio_num)

Disable gpio pad hold function.

When the chip is woken up from peripheral power-down sleep, the gpio will be set to the default mode, so, the gpio will output the default level if this function is called. If you don't want the level changes, the gpio should be configured to a known state before this function is called. e.g. If you hold gpio18 high during Deep-sleep, after the chip is woken up and gpio_hold_dis is called, gpio18 will output low level(because gpio18 is input mode by default). If you don't want this behavior, you should configure gpio18 as output mode and set it to hight level before calling gpio_hold_dis.

参数

gpio_num -- GPIO number, only support output-capable GPIOs

返回

• ESP_OK Success

• ESP_ERR_NOT_SUPPORTED Not support pad hold function

void gpio_deep_sleep_hold_en(void)

Enable all digital gpio pads hold function during Deep-sleep.

Enabling this feature makes all digital gpio pads be at the holding state during Deep-sleep. The state of each pad holds is its active configuration (not pad's sleep configuration!).

Note that this pad hold feature only works when the chip is in Deep-sleep mode. When the chip is in active mode, the digital gpio state can be changed freely even you have called this function.

After this API is being called, the digital gpio Deep-sleep hold feature will work during every sleep process. You should call gpio_deep_sleep_hold_dis to disable this feature.

void gpio_deep_sleep_hold_dis(void)

Disable all digital gpio pads hold function during Deep-sleep.

void gpio_iomux_in(uint32_t gpio_num, uint32_t signal_idx)

SOC_GPIO_SUPPORT_HOLD_SINGLE_IO_IN_DSLP.

Set pad input to a peripheral signal through the IOMUX.

参数

• gpio_num -- GPIO number of the pad.

• signal_idx -- Peripheral signal id to input. One of the *_IN_IDX signals in soc/gpio_sig_map.h.

void gpio_iomux_out(uint8_t gpio_num, int func, bool oen_inv)

Set peripheral output to an GPIO pad through the IOMUX.

参数

• gpio_num -- gpio_num GPIO number of the pad.

• func -- The function number of the peripheral pin to output pin. One of the FUNC_X_* of specified pin (X) in soc/io_mux_reg.h.

• oen_inv -- True if the output enable needs to be inverted, otherwise False.

esp_err_t gpio_force_hold_all(void)

Force hold all digital and rtc gpio pads.

GPIO force hold, no matter the chip in active mode or sleep modes.

This function will immediately cause all pads to latch the current values of input enable, output enable, output value, function, and drive strength values.

警告

1. This function will hold flash and UART pins as well. Therefore, this function, and all code run afterwards (till calling gpio_force_unhold_all to disable this feature), MUST be placed in internal RAM as holding the flash pins will halt SPI flash operation, and holding the UART pins will halt any UART logging.

2. The hold state of all pads will be cancelled during ROM boot, so it is not recommended to use this API to hold the pads state during deepsleep and reset.

esp_err_t gpio_force_unhold_all(void)

Unhold all digital and rtc gpio pads.

备注

The global hold signal and the hold signal of each IO act on the PAD through 'or' logic, so if a pad has already been configured to hold by gpio_hold_en, this API can't release its hold state.

esp_err_t gpio_sleep_sel_en(gpio_num_t gpio_num)

Enable SLP_SEL to change GPIO status automantically in lightsleep.

参数

gpio_num -- GPIO number of the pad.

返回

• ESP_OK Success

esp_err_t gpio_sleep_sel_dis(gpio_num_t gpio_num)

Disable SLP_SEL to change GPIO status automantically in lightsleep.

参数

gpio_num -- GPIO number of the pad.

返回

• ESP_OK Success

esp_err_t gpio_sleep_set_direction(gpio_num_t gpio_num, gpio_mode_t mode)

GPIO set direction at sleep.

Configure GPIO direction,such as output_only,input_only,output_and_input

参数

• gpio_num -- Configure GPIO pins number, it should be GPIO number. If you want to set direction of e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);

• mode -- GPIO direction

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO error

esp_err_t gpio_sleep_set_pull_mode(gpio_num_t gpio_num, gpio_pull_mode_t pull)

Configure GPIO pull-up/pull-down resistors at sleep.

备注

ESP32: Only pins that support both input & output have integrated pull-up and pull-down resistors. Input-only GPIOs 34-39 do not.

参数

• gpio_num -- GPIO number. If you want to set pull up or down mode for e.g. GPIO16, gpio_num should be GPIO_NUM_16 (16);

• pull -- GPIO pull up/down mode.

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG : Parameter error

esp_err_t gpio_dump_io_configuration(FILE *out_stream, uint64_t io_bit_mask)

Dump IO configuration information to console.

参数

• out_stream -- IO stream (e.g. stdout)

• io_bit_mask -- IO pin bit mask, each bit maps to an IO

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

Structures

struct gpio_config_t

Configuration parameters of GPIO pad for gpio_config function.

Public Members

uint64_t pin_bit_mask

GPIO pin: set with bit mask, each bit maps to a GPIO

gpio_mode_t mode

GPIO mode: set input/output mode

gpio_pullup_t pull_up_en

GPIO pull-up

gpio_pulldown_t pull_down_en

GPIO pull-down

gpio_int_type_t intr_type

GPIO interrupt type

Macros

GPIO_PIN_COUNT

GPIO_IS_VALID_GPIO(gpio_num)

Check whether it is a valid GPIO number.

GPIO_IS_VALID_OUTPUT_GPIO(gpio_num)

Check whether it can be a valid GPIO number of output mode.

GPIO_IS_VALID_DIGITAL_IO_PAD(gpio_num)

Check whether it can be a valid digital I/O pad.

Type Definitions

typedef intr_handle_t gpio_isr_handle_t

typedef void (*gpio_isr_t)(void *arg)

GPIO interrupt handler.

Param arg

User registered data

Header File

• components/hal/include/hal/gpio_types.h

Macros

GPIO_PIN_REG_0

GPIO_PIN_REG_1

GPIO_PIN_REG_2

GPIO_PIN_REG_3

GPIO_PIN_REG_4

GPIO_PIN_REG_5

GPIO_PIN_REG_6

GPIO_PIN_REG_7

GPIO_PIN_REG_8

GPIO_PIN_REG_9

GPIO_PIN_REG_10

GPIO_PIN_REG_11

GPIO_PIN_REG_12

GPIO_PIN_REG_13

GPIO_PIN_REG_14

GPIO_PIN_REG_15

GPIO_PIN_REG_16

GPIO_PIN_REG_17

GPIO_PIN_REG_18

GPIO_PIN_REG_19

GPIO_PIN_REG_20

GPIO_PIN_REG_21

GPIO_PIN_REG_22

GPIO_PIN_REG_23

GPIO_PIN_REG_24

GPIO_PIN_REG_25

GPIO_PIN_REG_26

GPIO_PIN_REG_27

GPIO_PIN_REG_28

GPIO_PIN_REG_29

GPIO_PIN_REG_30

GPIO_PIN_REG_31

GPIO_PIN_REG_32

GPIO_PIN_REG_33

GPIO_PIN_REG_34

GPIO_PIN_REG_35

GPIO_PIN_REG_36

GPIO_PIN_REG_37

GPIO_PIN_REG_38

GPIO_PIN_REG_39

GPIO_PIN_REG_40

GPIO_PIN_REG_41

GPIO_PIN_REG_42

GPIO_PIN_REG_43

GPIO_PIN_REG_44

GPIO_PIN_REG_45

GPIO_PIN_REG_46

GPIO_PIN_REG_47

GPIO_PIN_REG_48

Enumerations

enum gpio_port_t

Values:

enumerator GPIO_PORT_0

enumerator GPIO_PORT_MAX

enum gpio_num_t

Values:

enumerator GPIO_NUM_NC

Use to signal not connected to S/W

enumerator GPIO_NUM_0

GPIO0, input and output

enumerator GPIO_NUM_1

GPIO1, input and output

enumerator GPIO_NUM_2

GPIO2, input and output

enumerator GPIO_NUM_3

GPIO3, input and output

enumerator GPIO_NUM_4

GPIO4, input and output

enumerator GPIO_NUM_5

GPIO5, input and output

enumerator GPIO_NUM_6

GPIO6, input and output

enumerator GPIO_NUM_7

GPIO7, input and output

enumerator GPIO_NUM_8

GPIO8, input and output

enumerator GPIO_NUM_9

GPIO9, input and output

enumerator GPIO_NUM_10

GPIO10, input and output

enumerator GPIO_NUM_11

GPIO11, input and output

enumerator GPIO_NUM_12

GPIO12, input and output

enumerator GPIO_NUM_13

GPIO13, input and output

enumerator GPIO_NUM_14

GPIO14, input and output

enumerator GPIO_NUM_15

GPIO15, input and output

enumerator GPIO_NUM_16

GPIO16, input and output

enumerator GPIO_NUM_17

GPIO17, input and output

enumerator GPIO_NUM_18

GPIO18, input and output

enumerator GPIO_NUM_19

GPIO19, input and output

enumerator GPIO_NUM_20

GPIO20, input and output

enumerator GPIO_NUM_21

GPIO21, input and output

enumerator GPIO_NUM_26

GPIO26, input and output

enumerator GPIO_NUM_27

GPIO27, input and output

enumerator GPIO_NUM_28

GPIO28, input and output

enumerator GPIO_NUM_29

GPIO29, input and output

enumerator GPIO_NUM_30

GPIO30, input and output

enumerator GPIO_NUM_31

GPIO31, input and output

enumerator GPIO_NUM_32

GPIO32, input and output

enumerator GPIO_NUM_33

GPIO33, input and output

enumerator GPIO_NUM_34

GPIO34, input and output

enumerator GPIO_NUM_35

GPIO35, input and output

enumerator GPIO_NUM_36

GPIO36, input and output

enumerator GPIO_NUM_37

GPIO37, input and output

enumerator GPIO_NUM_38

GPIO38, input and output

enumerator GPIO_NUM_39

GPIO39, input and output

enumerator GPIO_NUM_40

GPIO40, input and output

enumerator GPIO_NUM_41

GPIO41, input and output

enumerator GPIO_NUM_42

GPIO42, input and output

enumerator GPIO_NUM_43

GPIO43, input and output

enumerator GPIO_NUM_44

GPIO44, input and output

enumerator GPIO_NUM_45

GPIO45, input and output

enumerator GPIO_NUM_46

GPIO46, input mode only

enumerator GPIO_NUM_MAX

enum gpio_int_type_t

Values:

enumerator GPIO_INTR_DISABLE

Disable GPIO interrupt

enumerator GPIO_INTR_POSEDGE

GPIO interrupt type : rising edge

enumerator GPIO_INTR_NEGEDGE

GPIO interrupt type : falling edge

enumerator GPIO_INTR_ANYEDGE

GPIO interrupt type : both rising and falling edge

enumerator GPIO_INTR_LOW_LEVEL

GPIO interrupt type : input low level trigger

enumerator GPIO_INTR_HIGH_LEVEL

GPIO interrupt type : input high level trigger

enumerator GPIO_INTR_MAX

enum gpio_mode_t

Values:

enumerator GPIO_MODE_DISABLE

GPIO mode : disable input and output

enumerator GPIO_MODE_INPUT

GPIO mode : input only

enumerator GPIO_MODE_OUTPUT

GPIO mode : output only mode

enumerator GPIO_MODE_OUTPUT_OD

GPIO mode : output only with open-drain mode

enumerator GPIO_MODE_INPUT_OUTPUT_OD

GPIO mode : output and input with open-drain mode

enumerator GPIO_MODE_INPUT_OUTPUT

GPIO mode : output and input mode

enum gpio_pullup_t

Values:

enumerator GPIO_PULLUP_DISABLE

Disable GPIO pull-up resistor

enumerator GPIO_PULLUP_ENABLE

Enable GPIO pull-up resistor

enum gpio_pulldown_t

Values:

enumerator GPIO_PULLDOWN_DISABLE

Disable GPIO pull-down resistor

enumerator GPIO_PULLDOWN_ENABLE

Enable GPIO pull-down resistor

enum gpio_pull_mode_t

Values:

enumerator GPIO_PULLUP_ONLY

Pad pull up

enumerator GPIO_PULLDOWN_ONLY

Pad pull down

enumerator GPIO_PULLUP_PULLDOWN

Pad pull up + pull down

enumerator GPIO_FLOATING

Pad floating

enum gpio_drive_cap_t

Values:

enumerator GPIO_DRIVE_CAP_0

Pad drive capability: weak

enumerator GPIO_DRIVE_CAP_1

Pad drive capability: stronger

enumerator GPIO_DRIVE_CAP_2

Pad drive capability: medium

enumerator GPIO_DRIVE_CAP_DEFAULT

Pad drive capability: medium

enumerator GPIO_DRIVE_CAP_3

Pad drive capability: strongest

enumerator GPIO_DRIVE_CAP_MAX

enum gpio_hys_ctrl_mode_t

Available option for configuring hysteresis feature of GPIOs.

Values:

enumerator GPIO_HYS_CTRL_EFUSE

Pad input hysteresis ctrl by efuse

enumerator GPIO_HYS_SOFT_ENABLE

Pad input hysteresis enable by software

enumerator GPIO_HYS_SOFT_DISABLE

Pad input hysteresis disable by software

API 参考 - RTC GPIO

Header File

• components/driver/gpio/include/driver/rtc_io.h

Functions

bool rtc_gpio_is_valid_gpio(gpio_num_t gpio_num)

Determine if the specified GPIO is a valid RTC GPIO.

参数

gpio_num -- GPIO number

返回

true if GPIO is valid for RTC GPIO use. false otherwise.

int rtc_io_number_get(gpio_num_t gpio_num)

Get RTC IO index number by gpio number.

参数

gpio_num -- GPIO number

返回

>=0: Index of rtcio. -1 : The gpio is not rtcio.

esp_err_t rtc_gpio_init(gpio_num_t gpio_num)

Init a GPIO as RTC GPIO.

This function must be called when initializing a pad for an analog function.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_deinit(gpio_num_t gpio_num)

Init a GPIO as digital GPIO.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

uint32_t rtc_gpio_get_level(gpio_num_t gpio_num)

Get the RTC IO input level.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• 1 High level

• 0 Low level

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_set_level(gpio_num_t gpio_num, uint32_t level)

Set the RTC IO output level.

参数

• gpio_num -- GPIO number (e.g. GPIO_NUM_12)

• level -- output level

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_set_direction(gpio_num_t gpio_num, rtc_gpio_mode_t mode)

RTC GPIO set direction.

Configure RTC GPIO direction, such as output only, input only, output and input.

参数

• gpio_num -- GPIO number (e.g. GPIO_NUM_12)

• mode -- GPIO direction

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_set_direction_in_sleep(gpio_num_t gpio_num, rtc_gpio_mode_t mode)

RTC GPIO set direction in deep sleep mode or disable sleep status (default). In some application scenarios, IO needs to have another states during deep sleep.

NOTE: ESP32 support INPUT_ONLY mode. ESP32S2 support INPUT_ONLY, OUTPUT_ONLY, INPUT_OUTPUT mode.

参数

• gpio_num -- GPIO number (e.g. GPIO_NUM_12)

• mode -- GPIO direction

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_pullup_en(gpio_num_t gpio_num)

RTC GPIO pullup enable.

This function only works for RTC IOs. In general, call gpio_pullup_en, which will work both for normal GPIOs and RTC IOs.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_pulldown_en(gpio_num_t gpio_num)

RTC GPIO pulldown enable.

This function only works for RTC IOs. In general, call gpio_pulldown_en, which will work both for normal GPIOs and RTC IOs.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_pullup_dis(gpio_num_t gpio_num)

RTC GPIO pullup disable.

This function only works for RTC IOs. In general, call gpio_pullup_dis, which will work both for normal GPIOs and RTC IOs.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_pulldown_dis(gpio_num_t gpio_num)

RTC GPIO pulldown disable.

This function only works for RTC IOs. In general, call gpio_pulldown_dis, which will work both for normal GPIOs and RTC IOs.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_set_drive_capability(gpio_num_t gpio_num, gpio_drive_cap_t strength)

Set RTC GPIO pad drive capability.

参数

• gpio_num -- GPIO number, only support output GPIOs

• strength -- Drive capability of the pad

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t rtc_gpio_get_drive_capability(gpio_num_t gpio_num, gpio_drive_cap_t *strength)

Get RTC GPIO pad drive capability.

参数

• gpio_num -- GPIO number, only support output GPIOs

• strength -- Pointer to accept drive capability of the pad

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG Parameter error

esp_err_t rtc_gpio_hold_en(gpio_num_t gpio_num)

Enable hold function on an RTC IO pad.

Enabling HOLD function will cause the pad to latch current values of input enable, output enable, output value, function, drive strength values. This function is useful when going into light or deep sleep mode to prevent the pin configuration from changing.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_hold_dis(gpio_num_t gpio_num)

Disable hold function on an RTC IO pad.

Disabling hold function will allow the pad receive the values of input enable, output enable, output value, function, drive strength from RTC_IO peripheral.

参数

gpio_num -- GPIO number (e.g. GPIO_NUM_12)

返回

• ESP_OK Success

• ESP_ERR_INVALID_ARG GPIO is not an RTC IO

esp_err_t rtc_gpio_force_hold_en_all(void)

Enable force hold signal for all RTC IOs.

Each RTC pad has a "force hold" input signal from the RTC controller. If this signal is set, pad latches current values of input enable, function, output enable, and other signals which come from the RTC mux. Force hold signal is enabled before going into deep sleep for pins which are used for EXT1 wakeup.

esp_err_t rtc_gpio_force_hold_dis_all(void)

Disable force hold signal for all RTC IOs.

esp_err_t rtc_gpio_wakeup_enable(gpio_num_t gpio_num, gpio_int_type_t intr_type)

Enable wakeup from sleep mode using specific GPIO.

参数

• gpio_num -- GPIO number

• intr_type -- Wakeup on high level (GPIO_INTR_HIGH_LEVEL) or low level (GPIO_INTR_LOW_LEVEL)

返回

• ESP_OK on success

• ESP_ERR_INVALID_ARG if gpio_num is not an RTC IO, or intr_type is not one of GPIO_INTR_HIGH_LEVEL, GPIO_INTR_LOW_LEVEL.

esp_err_t rtc_gpio_wakeup_disable(gpio_num_t gpio_num)

Disable wakeup from sleep mode using specific GPIO.

参数

gpio_num -- GPIO number

返回

• ESP_OK on success

• ESP_ERR_INVALID_ARG if gpio_num is not an RTC IO

Macros

RTC_GPIO_IS_VALID_GPIO(gpio_num)

Header File

• components/hal/include/hal/rtc_io_types.h

Enumerations

enum rtc_gpio_mode_t

RTCIO output/input mode type.

Values:

enumerator RTC_GPIO_MODE_INPUT_ONLY

Pad input

enumerator RTC_GPIO_MODE_OUTPUT_ONLY

Pad output

enumerator RTC_GPIO_MODE_INPUT_OUTPUT

Pad input + output

enumerator RTC_GPIO_MODE_DISABLED

Pad (output + input) disable

enumerator RTC_GPIO_MODE_OUTPUT_OD

Pad open-drain output

enumerator RTC_GPIO_MODE_INPUT_OUTPUT_OD

Pad input + open-drain output

API 参考 - GPIO 毛刺过滤器

Header File

• components/driver/gpio/include/driver/gpio_filter.h

Functions

esp_err_t gpio_new_pin_glitch_filter(const gpio_pin_glitch_filter_config_t *config, gpio_glitch_filter_handle_t *ret_filter)

Create a pin glitch filter.

备注

Pin glitch filter parameters are fixed, pulses shorter than two sample clocks (IO-MUX's source clock) will be filtered out. It's independent with "flex" glitch filter. See also gpio_new_flex_glitch_filter.

备注

The created filter handle can later be deleted by gpio_del_glitch_filter.

参数

• config -- [in] Glitch filter configuration

• ret_filter -- [out] Returned glitch filter handle

返回

• ESP_OK: Create a pin glitch filter successfully

• ESP_ERR_INVALID_ARG: Create a pin glitch filter failed because of invalid arguments (e.g. wrong GPIO number)

• ESP_ERR_NO_MEM: Create a pin glitch filter failed because of out of memory

• ESP_FAIL: Create a pin glitch filter failed because of other error

esp_err_t gpio_new_flex_glitch_filter(const gpio_flex_glitch_filter_config_t *config, gpio_glitch_filter_handle_t *ret_filter)

Allocate a flex glitch filter.

备注

"flex" means the filter parameters (window, threshold) are adjustable. It's independent with pin glitch filter. See also gpio_new_pin_glitch_filter.

备注

The created filter handle can later be deleted by gpio_del_glitch_filter.

参数

• config -- [in] Glitch filter configuration

• ret_filter -- [out] Returned glitch filter handle

返回

• ESP_OK: Allocate a flex glitch filter successfully

• ESP_ERR_INVALID_ARG: Allocate a flex glitch filter failed because of invalid arguments (e.g. wrong GPIO number, filter parameters out of range)

• ESP_ERR_NO_MEM: Allocate a flex glitch filter failed because of out of memory

• ESP_ERR_NOT_FOUND: Allocate a flex glitch filter failed because the underlying hardware resources are used up

• ESP_FAIL: Allocate a flex glitch filter failed because of other error

esp_err_t gpio_del_glitch_filter(gpio_glitch_filter_handle_t filter)

Delete a glitch filter.

参数

filter -- [in] Glitch filter handle returned from gpio_new_flex_glitch_filter or gpio_new_pin_glitch_filter

返回

• ESP_OK: Delete glitch filter successfully

• ESP_ERR_INVALID_ARG: Delete glitch filter failed because of invalid arguments

• ESP_ERR_INVALID_STATE: Delete glitch filter failed because the glitch filter is still in working

• ESP_FAIL: Delete glitch filter failed because of other error

esp_err_t gpio_glitch_filter_enable(gpio_glitch_filter_handle_t filter)

Enable a glitch filter.

参数

filter -- [in] Glitch filter handle returned from gpio_new_flex_glitch_filter or gpio_new_pin_glitch_filter

返回

• ESP_OK: Enable glitch filter successfully

• ESP_ERR_INVALID_ARG: Enable glitch filter failed because of invalid arguments

• ESP_ERR_INVALID_STATE: Enable glitch filter failed because the glitch filter is already enabled

• ESP_FAIL: Enable glitch filter failed because of other error

esp_err_t gpio_glitch_filter_disable(gpio_glitch_filter_handle_t filter)

Disable a glitch filter.

参数

filter -- [in] Glitch filter handle returned from gpio_new_flex_glitch_filter or gpio_new_pin_glitch_filter

返回

• ESP_OK: Disable glitch filter successfully

• ESP_ERR_INVALID_ARG: Disable glitch filter failed because of invalid arguments

• ESP_ERR_INVALID_STATE: Disable glitch filter failed because the glitch filter is not enabled yet

• ESP_FAIL: Disable glitch filter failed because of other error

Structures

struct gpio_pin_glitch_filter_config_t

Configuration of GPIO pin glitch filter.

Public Members

glitch_filter_clock_source_t clk_src

Clock source for the glitch filter

gpio_num_t gpio_num

GPIO number

struct gpio_flex_glitch_filter_config_t

Configuration of GPIO flex glitch filter.

Public Members

glitch_filter_clock_source_t clk_src

Clock source for the glitch filter

gpio_num_t gpio_num

GPIO number

uint32_t window_width_ns

Sample window width (in ns)

uint32_t window_thres_ns

Sample window threshold (in ns), during the window_width_ns sample window, any pulse whose width < window_thres_ns will be discarded.

Type Definitions

typedef struct gpio_glitch_filter_t *gpio_glitch_filter_handle_t

Typedef of GPIO glitch filter handle.

提供有关此文档的反馈