Index of Abbreviations¶
- A2DP
Advanced Audio Distribution Profile
高级音频分发框架
- ADC
Analog-to-Digital Converter
模拟数字转换器
- ALPN
Application Layer Protocol Negotiation
应用层协议协商
- AT port
AT port is the general name of AT log port (that is used to output log) and AT command port (that is used to send AT commands and receive responses). Please refer to 硬件连接 for default AT port pins and 如何修改 AT port 管脚 for how to customize them.
AT 端口是 AT 日志端口（用于输出日志）和 AT 命令端口（用于发送 AT 命令和接收响应）的总称。请参考 硬件连接 了解默认的 AT 端口管脚，参考 如何修改 AT port 管脚 了解如何自定义 AT 端口管脚。
- Bluetooth LE
Bluetooth Low Energy
低功耗蓝牙
- BluFi
Wi-Fi network configuration function via Bluetooth channel
BluFi 是一款基于蓝牙通道的 Wi-Fi 网络配置功能
- DHCP
Dynamic Host Configuration Protocol
动态主机配置协议
- DNS
Domain Name System
域名系统
- DTIM
Delivery Traffic Indication Map
延迟传输指示映射
- GATTC
Generic Attributes client
GATT 客户端
- GATTS
Generic Attributes server
GATT 服务器
- HID
Human Interface Device
人机接口设备
- I2C
Inter-Integrated Circuit
集成电路总线
- ICMP
Intemet Control Message Protocol
因特网控制报文协议
- LWT
Last Will and Testament
遗嘱
- MAC
Media Access Control
MAC 地址
- mDNS
Multicast Domain Name System
多播 DNS
- MSB
Most Significant Bit
最高有效位
- MTU
maximum transmission unit
最大传输单元
- NVS
Non-Volatile Storage
非易失性存储器
- Normal Transmission Mode
Default Transmission Mode
In normal transmission mode, users can send AT commands. For examples, users can send MCU data received by AT command port to the opposite end of transmission by AT+CIPSEND; and the data received from the opposite end of transmission will also be returned to MCU through AT command port with additional prompt: +IPD.
During a normal transmission, if the connection breaks, ESP devices will give a prompt and will not attempt to reconnect.
More details are in Transmission Mode Shift Diagram.
- 普通传输模式
默认传输模式
在普通传输模式下，用户可以发送 AT 命令。 例如，用户可以通过 AT+CIPSEND 命令，发送 AT 命令口收到的 MCU 数据到传输对端。从传输对端收到的数据，会通过 AT 命令口返回给 MCU，同时会附带 +IPD 信息。
普通传输模式时，如果连接断开，ESP 不会重连，并提示连接断开。
更多介绍请参考 Transmission Mode Shift Diagram。
- Passthrough Mode
Also called as “Passthrough Sending & Receiving Mode”.
In passthrough mode, users cannot send AT commands except special +++ command. All MCU data received by AT command port will be sent to the opposite end of transmission without any modification; and the data received from the opposite end of transmission will also be returned to MCU through AT command port without any modification.
During the Wi-Fi passthrough transmission, if the connection breaks, ESP devices will keep trying to reconnect until +++ is input to exit the passthrough transmission.
More details are in Transmission Mode Shift Diagram.
- 透传模式
也称为 “透传发送接收模式”。
在透传模式下，用户不能发送其它 AT 命令，除了特别的 +++ 命令。AT 命令口收到的所有的 MCU 数据都将无修改地，发送到传输对端。从传输对端收到的数据也会通过 AT 命令口无修改地，返回给 MCU。
Wi-Fi 透传模式传输时，如果连接断开，ESP 会不停地尝试重连，此时单独输入 +++ 退出透传，则停止重连。
更多介绍请参考 Transmission Mode Shift Diagram。
- Transmission Mode Shift Diagram
Transmission Mode Shift Diagram
More details are in the following introduction.
- Passthrough Receiving Mode
The temporary mode between Normal Transmission Mode and Passthrough Mode.
In passthrough receiving mode, AT cannot send any data to the opposite end of transmission; but the data received from the opposite end of transmission can be returned to MCU through AT command port without any modification. More details are in Transmission Mode Shift Diagram.
- 透传接收模式
-
在透传接收模式，AT 不能发送数据到传输对端；但 AT 可以收到来自传输对端的数据，通过 AT 命令口无修改地返回给 MCU。更多介绍请参考 Transmission Mode Shift Diagram。
- PBC
Push Button Configuration
按钮配置
- PCI Authentication
Payment Card Industry Authentication. In ESP-AT project, it refers to all Wi-Fi authentication modes except OPEN and WEP.
PCI 认证，在 ESP-AT 工程中指的是除 OPEN 和 WEP 以外的 Wi-Fi 认证模式。
- PLCP
Physical Layer Convergence Procedure
PLCP 协议，即物理层会聚协议
- PMF
protected management frame
受保护的管理帧
- PSK
Pre-shared Key
预共享密钥
- PWM
Pulse-Width Modulation
脉冲宽度调制
- QoS
Quality of Service
服务质量
- RTC
Real Time Controller. A group of circuits in SoC that keeps working in any chip mode and at any time.
实时控制器，为 SoC 中的一组电路，在任何芯片模式下都能随时保持工作。
- SMP
Security Manager Protocol
安全管理协议
- SNI
Server Name Indication
服务器名称指示
- SNTP
Simple Network Time Protocol
简单网络时间协议
- SPI
Serial Peripheral Interface
串行外设接口
- SPP
Serial Port Profile
SPP 协议，即串口协议
- SSL
Secure Sockets Layer
SSL 协议，即安全套接字协议
- TLS
Transport Layer Security
TLS 协议，即传输层安全性协议
- URC
Unsolicited Result Code
非请求结果码，一般为模组给 MCU 的串口返回
- UTC
Coordinated Universal Time
协调世界时
- UUID
universally unique identifier
通用唯一识别码
- WEP
Wired-Equivalent Privacy
WEP 加密方式，即有线等效加密
- WPA
Wi-Fi Protected Access
Wi-Fi 保护访问
- WPA2
Wi-Fi Protected Access II
Wi-Fi 保护访问 II
- WPS
Wi-Fi Protected Setup
Wi-Fi 保护设置