Touch Sensor¶

Introduction¶

A touch sensor system is built on a substrate which carries electrodes and relevant connections under a protective flat surface. When a user touches the surface, the capacitance variation is used to evaluate if the touch was valid.

ESP32-S2 can handle up to 14 capacitive touch pads / GPIOs.

The sensing pads can be arranged in different combinations (e.g., matrix, slider), so that a larger area or more points can be detected. The touch pad sensing process is under the control of a hardware-implemented finite-state machine (FSM) which is initiated by software or a dedicated hardware timer.

For design, operation, and control registers of a touch sensor, see ESP32-S2 Technical Reference Manual > On-Chip Sensors and Analog Signal Processing [PDF].

In-depth design details of touch sensors and firmware development guidelines for ESP32-S2 are available in Touch Sensor Application Note.

Functionality Overview¶

Description of API is broken down into groups of functions to provide a quick overview of the following features:

Initialization of touch pad driver
Configuration of touch pad GPIO pins
Taking measurements
Adjusting parameters of measurements
Filtering measurements
Touch detection methods
Setting up interrupts to report touch detection
Waking up from Sleep mode on interrupt

For detailed description of a particular function, please go to Section API Reference. Practical implementation of this API is covered in Section Application Examples.

Initialization¶

Before using a touch pad, you need to initialize the touch pad driver by calling the function touch_pad_init(). This function sets several .._DEFAULT driver parameters listed in API Reference under Macros. It also removes the information about which pads have been touched before, if any, and disables interrupts.

If the driver is not required anymore, deinitialize it by calling touch_pad_deinit().

Configuration¶

Enabling the touch sensor functionality for a particular GPIO is done with touch_pad_config().

Use the function touch_pad_set_fsm_mode() to select if touch pad measurement (operated by FSM) should be started automatically by a hardware timer, or by software. If software mode is selected, use touch_pad_sw_start() to start the FSM.

Touch State Measurements¶

The following function come in handy to read raw measurements from the sensor:

touch_pad_read_raw_data()

It can also be used, for example, to evaluate a particular touch pad design by checking the range of sensor readings when a pad is touched or released. This information can be then used to establish a touch threshold.

For the demonstration of how to read the touch pad data, check the application example peripherals/touch_pad_read.

Optimization of Measurements¶

A touch sensor has several configurable parameters to match the characteristics of a particular touch pad design. For instance, to sense smaller capacity changes, it is possible to narrow down the reference voltage range within which the touch pads are charged / discharged. The high and low reference voltages are set using the function touch_pad_set_voltage().

Besides the ability to discern smaller capacity changes, a positive side effect is reduction of power consumption for low power applications. A likely negative effect is an increase in measurement noise. If the dynamic range of obtained readings is still satisfactory, then further reduction of power consumption might be done by reducing the measurement time with touch_pad_set_meas_time().

The following list summarizes available measurement parameters and corresponding ‘set’ functions:

Touch pad charge / discharge parameters:
- voltage range: touch_pad_set_voltage()
- speed (slope): touch_pad_set_cnt_mode()
Measurement time: touch_pad_set_meas_time()

Relationship between the voltage range (high / low reference voltages), speed (slope), and measurement time is shown in the figure below.

Touch pad - relationship between measurement parameters¶

The last chart Output represents the touch sensor reading, i.e., the count of pulses collected within the measurement time.

All functions are provided in pairs to set a specific parameter and to get the current parameter’s value, e.g., touch_pad_set_voltage() and touch_pad_get_voltage().

Filtering of Measurements¶

If measurements are noisy, you can filter them with provided API functions. The ESP32-S2’s touch functionality provide two sets of APIs for doing this.

There is an internal touch channel that is not connected to any external GPIO. The measurements from this denoise pad can be used to filters out interference introduced on all channels, such as noise introduced by the power supply and external EMI. The denoise paramaters are set with the function touch_pad_denoise_set_config() and started by with touch_pad_denoise_enable()

There is also a configurable hardware implemented IIR-filter (infinite impulse response). This IIR-filter is configured with the function touch_pad_filter_set_config() and enabled by calling touch_pad_filter_enable()

Touch Detection¶

Touch detection is implemented in ESP32’s hardware based on the user-configured threshold and raw measurements executed by FSM. Use the functions touch_pad_get_status() to check which pads have been touched and touch_pad_clear_status() to clear the touch status information.

Hardware touch detection can also be wired to interrupts. This is described in the next section.

If measurements are noisy and capacity changes are small, hardware touch detection might be unreliable. To resolve this issue, instead of using hardware detection / provided interrupts, implement measurement filtering and perform touch detection in your own application. For sample implementation of both methods of touch detection, see peripherals/touch_pad_interrupt.

Touch Triggered Interrupts¶

Before enabling an interrupt on a touch detection, you should establish a touch detection threshold. Use the functions described in Touch State Measurements to read and display sensor measurements when a pad is touched and released. Apply a filter if measurements are noisy and relative capacity changes are small. Depending on your application and environment conditions, test the influence of temperature and power supply voltage changes on measured values.

Once a detection threshold is established, it can be set during initialization with touch_pad_config() or at the runtime with touch_pad_set_thresh().

Finally, configure and manage interrupt calls using the following functions:

touch_pad_isr_register() / touch_pad_isr_deregister()
touch_pad_intr_enable() / touch_pad_intr_disable()

When interrupts are operational, you can obtain the information from which particular pad an interrupt came by invoking touch_pad_get_status() and clear the pad status with touch_pad_clear_status().

Application Examples¶

Touch sensor read example: peripherals/touch_pad_read.
Touch sensor interrupt example: peripherals/touch_pad_interrupt.

API Reference¶

Header File¶

driver/esp32s2/include/driver/touch_sensor.h

Functions¶

esp_err_t touch_pad_fsm_start(void)¶

Set touch sensor FSM start.

Note

Start FSM after the touch sensor FSM mode is set.

Note

Call this function will reset benchmark of all touch channels.

Return

ESP_OK on success

esp_err_t touch_pad_fsm_stop(void)¶

Stop touch sensor FSM.

Return

ESP_OK on success

esp_err_t touch_pad_sw_start(void)¶

Trigger a touch sensor measurement, only support in SW mode of FSM.

Return

ESP_OK on success

esp_err_t touch_pad_set_meas_time(uint16_t sleep_cycle, uint16_t meas_times)¶

Set touch sensor times of charge and discharge and sleep time. Excessive total time will slow down the touch response. Too small measurement time will not be sampled enough, resulting in inaccurate measurements.

Note

The greater the duty cycle of the measurement time, the more system power is consumed.

Return

ESP_OK on success

Parameters

sleep_cycle: The touch sensor will sleep after each measurement. sleep_cycle decide the interval between each measurement. t_sleep = sleep_cycle / (RTC_SLOW_CLK frequency). The approximate frequency value of RTC_SLOW_CLK can be obtained using rtc_clk_slow_freq_get_hz function.
meas_times: The times of charge and discharge in each measure process of touch channels. The timer frequency is 8Mhz. Range: 0 ~ 0xffff. Recommended typical value: Modify this value to make the measurement time around 1ms.

esp_err_t touch_pad_get_meas_time(uint16_t *sleep_cycle, uint16_t *meas_times)¶

Get touch sensor times of charge and discharge and sleep time.

Return

ESP_OK on success

Parameters

sleep_cycle: Pointer to accept sleep cycle number
meas_times: Pointer to accept measurement times count.

esp_err_t touch_pad_set_idle_channel_connect(touch_pad_conn_type_t type)¶

Set connection type of touch channel in idle status. When a channel is in measurement mode, other initialized channels are in idle mode. The touch channel is generally adjacent to the trace, so the connection state of the idle channel affects the stability and sensitivity of the test channel. The CONN_HIGHZ(high resistance) setting increases the sensitivity of touch channels. The CONN_GND(grounding) setting increases the stability of touch channels.

Return

ESP_OK on success

Parameters

type: Select idle channel connect to high resistance state or ground.

esp_err_t touch_pad_get_idle_channel_connect(touch_pad_conn_type_t *type)¶

Set connection type of touch channel in idle status. When a channel is in measurement mode, other initialized channels are in idle mode. The touch channel is generally adjacent to the trace, so the connection state of the idle channel affects the stability and sensitivity of the test channel. The CONN_HIGHZ(high resistance) setting increases the sensitivity of touch channels. The CONN_GND(grounding) setting increases the stability of touch channels.

Return

ESP_OK on success

Parameters

type: Pointer to connection type.

esp_err_t touch_pad_set_thresh(touch_pad_t touch_num, uint32_t threshold)¶

Set the trigger threshold of touch sensor. The threshold determines the sensitivity of the touch sensor. The threshold is the original value of the trigger state minus the benchmark value.

Note

If set “TOUCH_PAD_THRESHOLD_MAX”, the touch is never be triggered.

Return

ESP_OK on success

Parameters

touch_num: touch pad index
threshold: threshold of touch sensor. Should be less than the max change value of touch.

esp_err_t touch_pad_get_thresh(touch_pad_t touch_num, uint32_t *threshold)¶

Get touch sensor trigger threshold.

Return

ESP_OK on success
ESP_ERR_INVALID_ARG if argument is wrong

Parameters

touch_num: touch pad index
threshold: pointer to accept threshold

esp_err_t touch_pad_set_channel_mask(uint16_t enable_mask)¶

Register touch channel into touch sensor scan group. The working mode of the touch sensor is cyclically scanned. This function will set the scan bits according to the given bitmask.

Note

If set this mask, the FSM timer should be stop firsty.

Note

The touch sensor that in scan map, should be deinit GPIO function firstly by touch_pad_io_init.

Return

ESP_OK on success

Parameters

enable_mask: bitmask of touch sensor scan group. e.g. TOUCH_PAD_NUM14 -> BIT(14)

esp_err_t touch_pad_get_channel_mask(uint16_t *enable_mask)¶

Get the touch sensor scan group bit mask.

Return

ESP_OK on success

Parameters

enable_mask: Pointer to bitmask of touch sensor scan group. e.g. TOUCH_PAD_NUM14 -> BIT(14)

esp_err_t touch_pad_clear_channel_mask(uint16_t enable_mask)¶

Clear touch channel from touch sensor scan group. The working mode of the touch sensor is cyclically scanned. This function will clear the scan bits according to the given bitmask.

Note

If clear all mask, the FSM timer should be stop firsty.

Return

ESP_OK on success

Parameters

enable_mask: bitmask of touch sensor scan group. e.g. TOUCH_PAD_NUM14 -> BIT(14)

esp_err_t touch_pad_config(touch_pad_t touch_num)¶

Configure parameter for each touch channel.

Note

Touch num 0 is denoise channel, please use touch_pad_denoise_enable to set denoise function

Return

ESP_OK Success
ESP_ERR_INVALID_ARG if argument wrong
ESP_FAIL if touch pad not initialized

Parameters

touch_num: touch pad index

esp_err_t touch_pad_reset(void)¶

Reset the FSM of touch module.

Note

Call this function after touch_pad_fsm_stop.

Return

ESP_OK Success

touch_pad_t touch_pad_get_current_meas_channel(void)¶

Get the current measure channel.

Note

Should be called when touch sensor measurement is in cyclic scan mode.

Return

touch channel number

uint32_t touch_pad_read_intr_status_mask(void)¶

Get the touch sensor interrupt status mask.

Return

touch interrupt bit

esp_err_t touch_pad_intr_enable(touch_pad_intr_mask_t int_mask)¶

Enable touch sensor interrupt by bitmask.

Note

This API can be called in ISR handler.

Return

ESP_OK on success

Parameters

int_mask: Pad mask to enable interrupts

esp_err_t touch_pad_intr_disable(touch_pad_intr_mask_t int_mask)¶

Disable touch sensor interrupt by bitmask.

Note

This API can be called in ISR handler.

Return

ESP_OK on success

Parameters

int_mask: Pad mask to disable interrupts

esp_err_t touch_pad_intr_clear(touch_pad_intr_mask_t int_mask)¶

Clear touch sensor interrupt by bitmask.

Return

ESP_OK on success

Parameters

int_mask: Pad mask to clear interrupts

esp_err_t touch_pad_isr_register(intr_handler_t fn, void *arg, touch_pad_intr_mask_t intr_mask)¶

Register touch-pad ISR. The handler will be attached to the same CPU core that this function is running on.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG Arguments error
ESP_ERR_NO_MEM No memory

Parameters

fn: Pointer to ISR handler
arg: Parameter for ISR
intr_mask: Enable touch sensor interrupt handler by bitmask.

esp_err_t touch_pad_timeout_set(bool enable, uint32_t threshold)¶

Enable/disable the timeout check and set timeout threshold for all touch sensor channels measurements. If enable: When the touch reading of a touch channel exceeds the measurement threshold, a timeout interrupt will be generated. If disable: the FSM does not check if the channel under measurement times out.

Note

The threshold compared with touch readings.

Note

In order to avoid abnormal short circuit of some touch channels. This function should be turned on. Ensure the normal operation of other touch channels.

Return

ESP_OK Success

Parameters

enable: true(default): Enable the timeout check; false: Disable the timeout check.
threshold: For all channels, the maximum value that will not be exceeded during normal operation.

esp_err_t touch_pad_timeout_resume(void)¶

Call this interface after timeout to make the touch channel resume normal work. Point on the next channel to measure. If this API is not called, the touch FSM will stop the measurement after timeout interrupt.

Note

Call this API after finishes the exception handling by user.

Return

ESP_OK Success

esp_err_t touch_pad_read_raw_data(touch_pad_t touch_num, uint32_t *raw_data)¶

get raw data of touch sensor.

Note

After the initialization is complete, the “raw_data” is max value. You need to wait for a measurement cycle before you can read the correct touch value.

Return

ESP_OK Success
ESP_FAIL Touch channel 0 haven’t this parameter.

Parameters

touch_num: touch pad index
raw_data: pointer to accept touch sensor value

esp_err_t touch_pad_read_benchmark(touch_pad_t touch_num, uint32_t *benchmark)¶

get benchmark of touch sensor.

Note

After initialization, the benchmark value is the maximum during the first measurement period.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG Touch channel 0 haven’t this parameter.

Parameters

touch_num: touch pad index
benchmark: pointer to accept touch sensor benchmark value

esp_err_t touch_pad_filter_read_smooth(touch_pad_t touch_num, uint32_t *smooth)¶

Get smoothed data that obtained by filtering the raw data.

Parameters

touch_num: touch pad index
smooth: pointer to smoothed data

esp_err_t touch_pad_reset_benchmark(touch_pad_t touch_num)¶

Force reset benchmark to raw data of touch sensor.

Return

ESP_OK Success

Parameters

touch_num: touch pad index
- TOUCH_PAD_MAX Reset basaline of all channels

esp_err_t touch_pad_filter_set_config(touch_filter_config_t *filter_info)¶

set parameter of touch sensor filter and detection algorithm. For more details on the detection algorithm, please refer to the application documentation.

Return

ESP_OK Success

Parameters

filter_info: select filter type and threshold of detection algorithm

esp_err_t touch_pad_filter_get_config(touch_filter_config_t *filter_info)¶

get parameter of touch sensor filter and detection algorithm. For more details on the detection algorithm, please refer to the application documentation.

Return

ESP_OK Success

Parameters

filter_info: select filter type and threshold of detection algorithm

esp_err_t touch_pad_filter_enable(void)¶

enable touch sensor filter for detection algorithm. For more details on the detection algorithm, please refer to the application documentation.

Return

ESP_OK Success

esp_err_t touch_pad_filter_disable(void)¶

disable touch sensor filter for detection algorithm. For more details on the detection algorithm, please refer to the application documentation.

Return

ESP_OK Success

esp_err_t touch_pad_denoise_set_config(touch_pad_denoise_t *denoise)¶

set parameter of denoise pad (TOUCH_PAD_NUM0). T0 is an internal channel that does not have a corresponding external GPIO. T0 will work simultaneously with the measured channel Tn. Finally, the actual measured value of Tn is the value after subtracting lower bits of T0. The noise reduction function filters out interference introduced simultaneously on all channels, such as noise introduced by power supplies and external EMI.

Return

ESP_OK Success

Parameters

denoise: parameter of denoise

esp_err_t touch_pad_denoise_get_config(touch_pad_denoise_t *denoise)¶

get parameter of denoise pad (TOUCH_PAD_NUM0).

Return

ESP_OK Success

Parameters

denoise: Pointer to parameter of denoise

esp_err_t touch_pad_denoise_enable(void)¶

enable denoise function. T0 is an internal channel that does not have a corresponding external GPIO. T0 will work simultaneously with the measured channel Tn. Finally, the actual measured value of Tn is the value after subtracting lower bits of T0. The noise reduction function filters out interference introduced simultaneously on all channels, such as noise introduced by power supplies and external EMI.

Return

ESP_OK Success

esp_err_t touch_pad_denoise_disable(void)¶

disable denoise function.

Return

ESP_OK Success

esp_err_t touch_pad_denoise_read_data(uint32_t *data)¶

Get denoise measure value (TOUCH_PAD_NUM0).

Return

ESP_OK Success

Parameters

data: Pointer to receive denoise value

esp_err_t touch_pad_waterproof_set_config(touch_pad_waterproof_t *waterproof)¶

set parameter of waterproof function.

   The waterproof function includes a shielded channel (TOUCH_PAD_NUM14) and a guard channel.
   Guard pad is used to detect the large area of water covering the touch panel.
   Shield pad is used to shield the influence of water droplets covering the touch panel.
   It is generally designed as a grid and is placed around the touch buttons.

Return

ESP_OK Success

Parameters

waterproof: parameter of waterproof

esp_err_t touch_pad_waterproof_get_config(touch_pad_waterproof_t *waterproof)¶

get parameter of waterproof function.

Return

ESP_OK Success

Parameters

waterproof: parameter of waterproof

esp_err_t touch_pad_waterproof_enable(void)¶

Enable parameter of waterproof function. Should be called after function touch_pad_waterproof_set_config.

Return

ESP_OK Success

esp_err_t touch_pad_waterproof_disable(void)¶

Disable parameter of waterproof function.

Return

ESP_OK Success

esp_err_t touch_pad_proximity_enable(touch_pad_t touch_num, bool enabled)¶

Enable/disable proximity function of touch channels. The proximity sensor measurement is the accumulation of touch channel measurements.

Note

Supports up to three touch channels configured as proximity sensors.

Return

ESP_OK: Configured correctly.
ESP_ERR_INVALID_ARG: Touch channel number error.
ESP_ERR_NOT_SUPPORTED: Don’t support configured.

Parameters

touch_num: touch pad index
enabled: true: enable the proximity function; false: disable the proximity function

esp_err_t touch_pad_proximity_set_count(touch_pad_t touch_num, uint32_t count)¶

Set measure count of proximity channel. The proximity sensor measurement is the accumulation of touch channel measurements.

Note

All proximity channels use the same count value. So please pass the parameter TOUCH_PAD_MAX.

Return

ESP_OK: Configured correctly.
ESP_ERR_INVALID_ARG: Touch channel number error.

Parameters

touch_num: Touch pad index. In this version, pass the parameter TOUCH_PAD_MAX.
count: The cumulative times of measurements for proximity pad. Range: 0 ~ 255.

esp_err_t touch_pad_proximity_get_count(touch_pad_t touch_num, uint32_t *count)¶

Get measure count of proximity channel. The proximity sensor measurement is the accumulation of touch channel measurements.

Note

All proximity channels use the same count value. So please pass the parameter TOUCH_PAD_MAX.

Return

ESP_OK: Configured correctly.
ESP_ERR_INVALID_ARG: Touch channel number error.

Parameters

touch_num: Touch pad index. In this version, pass the parameter TOUCH_PAD_MAX.
count: The cumulative times of measurements for proximity pad. Range: 0 ~ 255.

esp_err_t touch_pad_proximity_get_data(touch_pad_t touch_num, uint32_t *measure_out)¶

Get the accumulated measurement of the proximity sensor. The proximity sensor measurement is the accumulation of touch channel measurements.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG Touch num is not proximity

Parameters

touch_num: touch pad index
measure_out: If the accumulation process does not end, the measure_out is the process value.

esp_err_t touch_pad_sleep_channel_get_info(touch_pad_sleep_channel_t *slp_config)¶

Get parameter of touch sensor sleep channel. The touch sensor can works in sleep mode to wake up sleep.

Note

After the sleep channel is configured, Please use special functions for sleep channel. e.g. The user should uses touch_pad_sleep_channel_read_data instead of touch_pad_read_raw_data to obtain the sleep channel reading.

Return

ESP_OK Success

Parameters

slp_config: touch sleep pad config.

esp_err_t touch_pad_sleep_channel_enable(touch_pad_t pad_num, bool enable)¶

Enable/Disable sleep channel function for touch sensor. The touch sensor can works in sleep mode to wake up sleep.

Note

ESP32S2 only support one sleep channel.

Note

After the sleep channel is configured, Please use special functions for sleep channel. e.g. The user should uses touch_pad_sleep_channel_read_data instead of touch_pad_read_raw_data to obtain the sleep channel reading.

Return

ESP_OK Success

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
enable: true: enable sleep pad for touch sensor; false: disable sleep pad for touch sensor;

esp_err_t touch_pad_sleep_channel_enable_proximity(touch_pad_t pad_num, bool enable)¶

Enable/Disable proximity function for sleep channel. The touch sensor can works in sleep mode to wake up sleep.

Note

ESP32S2 only support one sleep channel.

Return

ESP_OK Success

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
enable: true: enable proximity for sleep channel; false: disable proximity for sleep channel;

esp_err_t touch_pad_sleep_set_threshold(touch_pad_t pad_num, uint32_t touch_thres)¶

Set the trigger threshold of touch sensor in deep sleep. The threshold determines the sensitivity of the touch sensor.

Note

In general, the touch threshold during sleep can use the threshold parameter parameters before sleep.

Return

ESP_OK Success

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
touch_thres: touch sleep pad threshold

esp_err_t touch_pad_sleep_get_threshold(touch_pad_t pad_num, uint32_t *touch_thres)¶

Get the trigger threshold of touch sensor in deep sleep. The threshold determines the sensitivity of the touch sensor.

Note

In general, the touch threshold during sleep can use the threshold parameter parameters before sleep.

Return

ESP_OK Success

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
touch_thres: touch sleep pad threshold

esp_err_t touch_pad_sleep_channel_read_benchmark(touch_pad_t pad_num, uint32_t *benchmark)¶

Read benchmark of touch sensor sleep channel.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG parameter is NULL

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
benchmark: pointer to accept touch sensor benchmark value

esp_err_t touch_pad_sleep_channel_read_smooth(touch_pad_t pad_num, uint32_t *smooth_data)¶

Read smoothed data of touch sensor sleep channel. Smoothed data is filtered from the raw data.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG parameter is NULL

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
smooth_data: pointer to accept touch sensor smoothed data

esp_err_t touch_pad_sleep_channel_read_data(touch_pad_t pad_num, uint32_t *raw_data)¶

Read raw data of touch sensor sleep channel.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG parameter is NULL

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
raw_data: pointer to accept touch sensor raw data

esp_err_t touch_pad_sleep_channel_reset_benchmark(void)¶

Reset benchmark of touch sensor sleep channel.

Return

ESP_OK Success

esp_err_t touch_pad_sleep_channel_read_proximity_cnt(touch_pad_t pad_num, uint32_t *proximity_cnt)¶

Read proximity count of touch sensor sleep channel.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG parameter is NULL

Parameters

pad_num: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode.
proximity_cnt: pointer to accept touch sensor proximity count value

esp_err_t touch_pad_sleep_channel_set_work_time(uint16_t sleep_cycle, uint16_t meas_times)¶

Change the operating frequency of touch pad in deep sleep state. Reducing the operating frequency can effectively reduce power consumption. If this function is not called, the working frequency of touch in the deep sleep state is the same as that in the wake-up state.

Return

ESP_OK Success

Parameters

sleep_cycle: The touch sensor will sleep after each measurement. sleep_cycle decide the interval between each measurement. t_sleep = sleep_cycle / (RTC_SLOW_CLK frequency). The approximate frequency value of RTC_SLOW_CLK can be obtained using rtc_clk_slow_freq_get_hz function.
meas_times: The times of charge and discharge in each measure process of touch channels. The timer frequency is 8Mhz. Range: 0 ~ 0xffff. Recommended typical value: Modify this value to make the measurement time around 1ms.

Header File¶

driver/include/driver/touch_sensor_common.h

Functions¶

esp_err_t touch_pad_init(void)¶

Initialize touch module.

Note

If default parameter don’t match the usage scenario, it can be changed after this function.

Return

ESP_OK Success
ESP_ERR_NO_MEM Touch pad init error
ESP_ERR_NOT_SUPPORTED Touch pad is providing current to external XTAL

esp_err_t touch_pad_deinit(void)¶

Un-install touch pad driver.

Note

After this function is called, other touch functions are prohibited from being called.

Return

ESP_OK Success
ESP_FAIL Touch pad driver not initialized

esp_err_t touch_pad_io_init(touch_pad_t touch_num)¶

Initialize touch pad GPIO.

Return

ESP_OK on success
ESP_ERR_INVALID_ARG if argument is wrong

Parameters

touch_num: touch pad index

esp_err_t touch_pad_set_voltage(touch_high_volt_t refh, touch_low_volt_t refl, touch_volt_atten_t atten)¶

Set touch sensor high voltage threshold of chanrge. The touch sensor measures the channel capacitance value by charging and discharging the channel. So the high threshold should be less than the supply voltage.

Return

ESP_OK on success
ESP_ERR_INVALID_ARG if argument is wrong

Parameters

refh: the value of DREFH
refl: the value of DREFL
atten: the attenuation on DREFH

esp_err_t touch_pad_get_voltage(touch_high_volt_t *refh, touch_low_volt_t *refl, touch_volt_atten_t *atten)¶

Get touch sensor reference voltage,.

Return

ESP_OK on success

Parameters

refh: pointer to accept DREFH value
refl: pointer to accept DREFL value
atten: pointer to accept the attenuation on DREFH

esp_err_t touch_pad_set_cnt_mode(touch_pad_t touch_num, touch_cnt_slope_t slope, touch_tie_opt_t opt)¶

Set touch sensor charge/discharge speed for each pad. If the slope is 0, the counter would always be zero. If the slope is 1, the charging and discharging would be slow, accordingly. If the slope is set 7, which is the maximum value, the charging and discharging would be fast.

Note

The higher the charge and discharge current, the greater the immunity of the touch channel, but it will increase the system power consumption.

Return

ESP_OK on success
ESP_ERR_INVALID_ARG if argument is wrong

Parameters

touch_num: touch pad index
slope: touch pad charge/discharge speed
opt: the initial voltage

esp_err_t touch_pad_get_cnt_mode(touch_pad_t touch_num, touch_cnt_slope_t *slope, touch_tie_opt_t *opt)¶

Get touch sensor charge/discharge speed for each pad.

Return

ESP_OK on success
ESP_ERR_INVALID_ARG if argument is wrong

Parameters

touch_num: touch pad index
slope: pointer to accept touch pad charge/discharge slope
opt: pointer to accept the initial voltage

esp_err_t touch_pad_isr_deregister(void (*fn)(void *), void *arg, )¶

Deregister the handler previously registered using touch_pad_isr_handler_register.

Return

ESP_OK on success
ESP_ERR_INVALID_STATE if a handler matching both fn and arg isn’t registered

Parameters

fn: handler function to call (as passed to touch_pad_isr_handler_register)
arg: argument of the handler (as passed to touch_pad_isr_handler_register)

esp_err_t touch_pad_get_wakeup_status(touch_pad_t *pad_num)¶

Get the touch pad which caused wakeup from deep sleep.

Return

ESP_OK Success
ESP_ERR_INVALID_ARG parameter is NULL

Parameters

pad_num: pointer to touch pad which caused wakeup

esp_err_t touch_pad_set_fsm_mode(touch_fsm_mode_t mode)¶

Set touch sensor FSM mode, the test action can be triggered by the timer, as well as by the software.

Return

ESP_OK on success
ESP_ERR_INVALID_ARG if argument is wrong

Parameters

mode: FSM mode

esp_err_t touch_pad_get_fsm_mode(touch_fsm_mode_t *mode)¶

Get touch sensor FSM mode.

Return

ESP_OK on success

Parameters

mode: pointer to accept FSM mode

esp_err_t touch_pad_clear_status(void)¶

To clear the touch sensor channel active status.

Note

The FSM automatically updates the touch sensor status. It is generally not necessary to call this API to clear the status.

Return

ESP_OK on success

uint32_t touch_pad_get_status(void)¶

Get the touch sensor channel active status mask. The bit position represents the channel number. The 0/1 status of the bit represents the trigger status.

Return

The touch sensor status. e.g. Touch1 trigger status is status_mask & (BIT1).

bool touch_pad_meas_is_done(void)¶

Check touch sensor measurement status.

Return

True measurement is under way
False measurement done

GPIO Lookup Macros¶

Some useful macros can be used to specified the GPIO number of a touch pad channel, or vice versa. e.g.

TOUCH_PAD_NUM5_GPIO_NUM is the GPIO number of channel 5 (12);
TOUCH_PAD_GPIO4_CHANNEL is the channel number of GPIO 4 (channel 0).

Header File¶

soc/esp32s2/include/soc/touch_sensor_channel.h

Macros¶

TOUCH_PAD_GPIO1_CHANNEL¶

TOUCH_PAD_NUM1_GPIO_NUM¶

TOUCH_PAD_GPIO2_CHANNEL¶

TOUCH_PAD_NUM2_GPIO_NUM¶

TOUCH_PAD_GPIO3_CHANNEL¶

TOUCH_PAD_NUM3_GPIO_NUM¶

TOUCH_PAD_GPIO4_CHANNEL¶

TOUCH_PAD_NUM4_GPIO_NUM¶

TOUCH_PAD_GPIO5_CHANNEL¶

TOUCH_PAD_NUM5_GPIO_NUM¶

TOUCH_PAD_GPIO6_CHANNEL¶

TOUCH_PAD_NUM6_GPIO_NUM¶

TOUCH_PAD_GPIO7_CHANNEL¶

TOUCH_PAD_NUM7_GPIO_NUM¶

TOUCH_PAD_GPIO8_CHANNEL¶

TOUCH_PAD_NUM8_GPIO_NUM¶

TOUCH_PAD_GPIO9_CHANNEL¶

TOUCH_PAD_NUM9_GPIO_NUM¶

TOUCH_PAD_GPIO10_CHANNEL¶

TOUCH_PAD_NUM10_GPIO_NUM¶

TOUCH_PAD_GPIO11_CHANNEL¶

TOUCH_PAD_NUM11_GPIO_NUM¶

TOUCH_PAD_GPIO12_CHANNEL¶

TOUCH_PAD_NUM12_GPIO_NUM¶

TOUCH_PAD_GPIO13_CHANNEL¶

TOUCH_PAD_NUM13_GPIO_NUM¶

TOUCH_PAD_GPIO14_CHANNEL¶

TOUCH_PAD_NUM14_GPIO_NUM¶

Header File¶

hal/include/hal/touch_sensor_types.h

Structures¶

struct touch_pad_denoise¶

Touch sensor denoise configuration

Public Members

touch_pad_denoise_grade_t grade¶: Select denoise range of denoise channel. Determined by measuring the noise amplitude of the denoise channel.

touch_pad_denoise_cap_t cap_level¶: Select internal reference capacitance of denoise channel. Ensure that the denoise readings are closest to the readings of the channel being measured. Use touch_pad_denoise_read_data to get the reading of denoise channel. The equivalent capacitance of the shielded channel can be calculated from the reading of denoise channel.

struct touch_pad_waterproof¶

Touch sensor waterproof configuration

Public Members

touch_pad_t guard_ring_pad¶: Waterproof. Select touch channel use for guard pad. Guard pad is used to detect the large area of water covering the touch panel.

touch_pad_shield_driver_t shield_driver¶: Waterproof. Shield channel drive capability configuration. Shield pad is used to shield the influence of water droplets covering the touch panel. When the waterproof function is enabled, Touch14 is set as shield channel by default. The larger the parasitic capacitance on the shielding channel, the higher the drive capability needs to be set. The equivalent capacitance of the shield channel can be estimated through the reading value of the denoise channel(Touch0).

struct touch_filter_config¶

Touch sensor filter configuration

Public Members

touch_filter_mode_t mode¶: Set filter mode. The input of the filter is the raw value of touch reading, and the output of the filter is involved in the judgment of the touch state.

uint32_t debounce_cnt¶: Set debounce count, such as n. If the measured values continue to exceed the threshold for n+1 times, the touch sensor state changes. Range: 0 ~ 7

uint32_t noise_thr¶: Noise threshold coefficient. Higher = More noise resistance. The actual noise should be less than (noise coefficient * touch threshold). Range: 0 ~ 3. The coefficient is 0: 4/8; 1: 3/8; 2: 2/8; 3: 1;

uint32_t jitter_step¶: Set jitter filter step size. Range: 0 ~ 15

touch_smooth_mode_t smh_lvl¶: Level of filter applied on the original data against large noise interference.

struct touch_pad_sleep_channel_t¶

Touch sensor channel sleep configuration

Public Members

touch_pad_t touch_num¶: Set touch channel number for sleep pad. Only one touch sensor channel is supported in deep sleep mode. If clear the sleep channel, point this pad to TOUCH_PAD_NUM0

bool en_proximity¶: enable proximity function for sleep pad

Macros¶

TOUCH_PAD_BIT_MASK_ALL¶

TOUCH_PAD_SLOPE_DEFAULT¶

TOUCH_PAD_TIE_OPT_DEFAULT¶

TOUCH_PAD_BIT_MASK_MAX¶

TOUCH_PAD_HIGH_VOLTAGE_THRESHOLD¶

TOUCH_PAD_LOW_VOLTAGE_THRESHOLD¶

TOUCH_PAD_ATTEN_VOLTAGE_THRESHOLD¶

TOUCH_PAD_IDLE_CH_CONNECT_DEFAULT¶

TOUCH_PAD_THRESHOLD_MAX¶: If set touch threshold max value, The touch sensor can’t be in touched status

TOUCH_PAD_SLEEP_CYCLE_DEFAULT¶

Excessive total time will slow down the touch response. Too small measurement time will not be sampled enough, resulting in inaccurate measurements.

Note: The greater the duty cycle of the measurement time, the more system power is consumed. The number of sleep cycle in each measure process of touch channels. The timer frequency is RTC_SLOW_CLK (can be 150k or 32k depending on the options). Range: 0 ~ 0xffff

TOUCH_PAD_MEASURE_CYCLE_DEFAULT¶: The times of charge and discharge in each measure process of touch channels. The timer frequency is 8Mhz. Recommended typical value: Modify this value to make the measurement time around 1ms. Range: 0 ~ 0xffff

TOUCH_PAD_INTR_MASK_ALL¶: All touch interrupt type enable.

TOUCH_PROXIMITY_MEAS_NUM_MAX¶: Touch sensor proximity detection configuration

TOUCH_DEBOUNCE_CNT_MAX¶

TOUCH_NOISE_THR_MAX¶

TOUCH_JITTER_STEP_MAX¶

Type Definitions¶

typedef struct touch_pad_denoise touch_pad_denoise_t¶: Touch sensor denoise configuration

typedef struct touch_pad_waterproof touch_pad_waterproof_t¶: Touch sensor waterproof configuration

typedef struct touch_filter_config touch_filter_config_t¶: Touch sensor filter configuration

Enumerations¶

enum touch_pad_t¶

Touch pad channel

Values:

TOUCH_PAD_NUM0 = 0¶: Touch pad channel 0 is GPIO4(ESP32)

TOUCH_PAD_NUM1¶: Touch pad channel 1 is GPIO0(ESP32) / GPIO1(ESP32-S2)

TOUCH_PAD_NUM2¶: Touch pad channel 2 is GPIO2(ESP32) / GPIO2(ESP32-S2)

TOUCH_PAD_NUM3¶: Touch pad channel 3 is GPIO15(ESP32) / GPIO3(ESP32-S2)

TOUCH_PAD_NUM4¶: Touch pad channel 4 is GPIO13(ESP32) / GPIO4(ESP32-S2)

TOUCH_PAD_NUM5¶: Touch pad channel 5 is GPIO12(ESP32) / GPIO5(ESP32-S2)

TOUCH_PAD_NUM6¶: Touch pad channel 6 is GPIO14(ESP32) / GPIO6(ESP32-S2)

TOUCH_PAD_NUM7¶: Touch pad channel 7 is GPIO27(ESP32) / GPIO7(ESP32-S2)

TOUCH_PAD_NUM8¶: Touch pad channel 8 is GPIO33(ESP32) / GPIO8(ESP32-S2)

TOUCH_PAD_NUM9¶: Touch pad channel 9 is GPIO32(ESP32) / GPIO9(ESP32-S2)

TOUCH_PAD_NUM10¶: Touch channel 10 is GPIO10(ESP32-S2)

TOUCH_PAD_NUM11¶: Touch channel 11 is GPIO11(ESP32-S2)

TOUCH_PAD_NUM12¶: Touch channel 12 is GPIO12(ESP32-S2)

TOUCH_PAD_NUM13¶: Touch channel 13 is GPIO13(ESP32-S2)

TOUCH_PAD_NUM14¶: Touch channel 14 is GPIO14(ESP32-S2)

TOUCH_PAD_MAX¶

enum touch_high_volt_t¶

Touch sensor high reference voltage

Values:

TOUCH_HVOLT_KEEP = -1¶: Touch sensor high reference voltage, no change

TOUCH_HVOLT_2V4 = 0¶: Touch sensor high reference voltage, 2.4V

TOUCH_HVOLT_2V5¶: Touch sensor high reference voltage, 2.5V

TOUCH_HVOLT_2V6¶: Touch sensor high reference voltage, 2.6V

TOUCH_HVOLT_2V7¶: Touch sensor high reference voltage, 2.7V

TOUCH_HVOLT_MAX¶

enum touch_low_volt_t¶

Touch sensor low reference voltage

Values:

TOUCH_LVOLT_KEEP = -1¶: Touch sensor low reference voltage, no change

TOUCH_LVOLT_0V5 = 0¶: Touch sensor low reference voltage, 0.5V

TOUCH_LVOLT_0V6¶: Touch sensor low reference voltage, 0.6V

TOUCH_LVOLT_0V7¶: Touch sensor low reference voltage, 0.7V

TOUCH_LVOLT_0V8¶: Touch sensor low reference voltage, 0.8V

TOUCH_LVOLT_MAX¶

enum touch_volt_atten_t¶

Touch sensor high reference voltage attenuation

Values:

TOUCH_HVOLT_ATTEN_KEEP = -1¶: Touch sensor high reference voltage attenuation, no change

TOUCH_HVOLT_ATTEN_1V5 = 0¶: Touch sensor high reference voltage attenuation, 1.5V attenuation

TOUCH_HVOLT_ATTEN_1V¶: Touch sensor high reference voltage attenuation, 1.0V attenuation

TOUCH_HVOLT_ATTEN_0V5¶: Touch sensor high reference voltage attenuation, 0.5V attenuation

TOUCH_HVOLT_ATTEN_0V¶: Touch sensor high reference voltage attenuation, 0V attenuation

TOUCH_HVOLT_ATTEN_MAX¶

enum touch_cnt_slope_t¶

Touch sensor charge/discharge speed

Values:

TOUCH_PAD_SLOPE_0 = 0¶: Touch sensor charge / discharge speed, always zero

TOUCH_PAD_SLOPE_1 = 1¶: Touch sensor charge / discharge speed, slowest

TOUCH_PAD_SLOPE_2 = 2¶: Touch sensor charge / discharge speed

TOUCH_PAD_SLOPE_3 = 3¶: Touch sensor charge / discharge speed

TOUCH_PAD_SLOPE_4 = 4¶: Touch sensor charge / discharge speed

TOUCH_PAD_SLOPE_5 = 5¶: Touch sensor charge / discharge speed

TOUCH_PAD_SLOPE_6 = 6¶: Touch sensor charge / discharge speed

TOUCH_PAD_SLOPE_7 = 7¶: Touch sensor charge / discharge speed, fast

TOUCH_PAD_SLOPE_MAX¶

enum touch_tie_opt_t¶

Touch sensor initial charge level

Values:

TOUCH_PAD_TIE_OPT_LOW = 0¶: Initial level of charging voltage, low level

TOUCH_PAD_TIE_OPT_HIGH = 1¶: Initial level of charging voltage, high level

TOUCH_PAD_TIE_OPT_MAX¶

enum touch_fsm_mode_t¶

Touch sensor FSM mode

Values:

TOUCH_FSM_MODE_TIMER = 0¶: To start touch FSM by timer

TOUCH_FSM_MODE_SW¶: To start touch FSM by software trigger

TOUCH_FSM_MODE_MAX¶

enum touch_trigger_mode_t¶

Values:

TOUCH_TRIGGER_BELOW = 0¶: Touch interrupt will happen if counter value is less than threshold.

TOUCH_TRIGGER_ABOVE = 1¶: Touch interrupt will happen if counter value is larger than threshold.

TOUCH_TRIGGER_MAX¶

enum touch_trigger_src_t¶

Values:

TOUCH_TRIGGER_SOURCE_BOTH = 0¶: wakeup interrupt is generated if both SET1 and SET2 are “touched”

TOUCH_TRIGGER_SOURCE_SET1 = 1¶: wakeup interrupt is generated if SET1 is “touched”

TOUCH_TRIGGER_SOURCE_MAX¶

enum touch_pad_intr_mask_t¶

Values:

TOUCH_PAD_INTR_MASK_DONE = BIT(0)¶: Measurement done for one of the enabled channels.

TOUCH_PAD_INTR_MASK_ACTIVE = BIT(1)¶: Active for one of the enabled channels.

TOUCH_PAD_INTR_MASK_INACTIVE = BIT(2)¶: Inactive for one of the enabled channels.

TOUCH_PAD_INTR_MASK_SCAN_DONE = BIT(3)¶: Measurement done for all the enabled channels.

TOUCH_PAD_INTR_MASK_TIMEOUT = BIT(4)¶: Timeout for one of the enabled channels.

enum touch_pad_denoise_grade_t¶

Values:

TOUCH_PAD_DENOISE_BIT12 = 0¶: Denoise range is 12bit

TOUCH_PAD_DENOISE_BIT10 = 1¶: Denoise range is 10bit

TOUCH_PAD_DENOISE_BIT8 = 2¶: Denoise range is 8bit

TOUCH_PAD_DENOISE_BIT4 = 3¶: Denoise range is 4bit

TOUCH_PAD_DENOISE_MAX¶

enum touch_pad_denoise_cap_t¶

Values:

TOUCH_PAD_DENOISE_CAP_L0 = 0¶: Denoise channel internal reference capacitance is 5pf

TOUCH_PAD_DENOISE_CAP_L1 = 1¶: Denoise channel internal reference capacitance is 6.4pf

TOUCH_PAD_DENOISE_CAP_L2 = 2¶: Denoise channel internal reference capacitance is 7.8pf

TOUCH_PAD_DENOISE_CAP_L3 = 3¶: Denoise channel internal reference capacitance is 9.2pf

TOUCH_PAD_DENOISE_CAP_L4 = 4¶: Denoise channel internal reference capacitance is 10.6pf

TOUCH_PAD_DENOISE_CAP_L5 = 5¶: Denoise channel internal reference capacitance is 12.0pf

TOUCH_PAD_DENOISE_CAP_L6 = 6¶: Denoise channel internal reference capacitance is 13.4pf

TOUCH_PAD_DENOISE_CAP_L7 = 7¶: Denoise channel internal reference capacitance is 14.8pf

TOUCH_PAD_DENOISE_CAP_MAX = 8¶

enum touch_pad_shield_driver_t¶

Touch sensor shield channel drive capability level

Values:

TOUCH_PAD_SHIELD_DRV_L0 = 0¶: The max equivalent capacitance in shield channel is 40pf

TOUCH_PAD_SHIELD_DRV_L1¶: The max equivalent capacitance in shield channel is 80pf

TOUCH_PAD_SHIELD_DRV_L2¶: The max equivalent capacitance in shield channel is 120pf

TOUCH_PAD_SHIELD_DRV_L3¶: The max equivalent capacitance in shield channel is 160pf

TOUCH_PAD_SHIELD_DRV_L4¶: The max equivalent capacitance in shield channel is 200pf

TOUCH_PAD_SHIELD_DRV_L5¶: The max equivalent capacitance in shield channel is 240pf

TOUCH_PAD_SHIELD_DRV_L6¶: The max equivalent capacitance in shield channel is 280pf

TOUCH_PAD_SHIELD_DRV_L7¶: The max equivalent capacitance in shield channel is 320pf

TOUCH_PAD_SHIELD_DRV_MAX¶

enum touch_pad_conn_type_t¶

Touch channel idle state configuration

Values:

TOUCH_PAD_CONN_HIGHZ = 0¶: Idle status of touch channel is high resistance state

TOUCH_PAD_CONN_GND = 1¶: Idle status of touch channel is ground connection

TOUCH_PAD_CONN_MAX¶

enum touch_filter_mode_t¶

Touch channel IIR filter coefficient configuration.

Note: On ESP32S2. There is an error in the IIR calculation. The magnitude of the error is twice the filter coefficient. So please select a smaller filter coefficient on the basis of meeting the filtering requirements. Recommended filter coefficient selection IIR_16.

Values:

TOUCH_PAD_FILTER_IIR_4 = 0¶: The filter mode is first-order IIR filter. The coefficient is 4.

TOUCH_PAD_FILTER_IIR_8¶: The filter mode is first-order IIR filter. The coefficient is 8.

TOUCH_PAD_FILTER_IIR_16¶: The filter mode is first-order IIR filter. The coefficient is 16 (Typical value).

TOUCH_PAD_FILTER_IIR_32¶: The filter mode is first-order IIR filter. The coefficient is 32.

TOUCH_PAD_FILTER_IIR_64¶: The filter mode is first-order IIR filter. The coefficient is 64.

TOUCH_PAD_FILTER_IIR_128¶: The filter mode is first-order IIR filter. The coefficient is 128.

TOUCH_PAD_FILTER_IIR_256¶: The filter mode is first-order IIR filter. The coefficient is 256.

TOUCH_PAD_FILTER_JITTER¶: The filter mode is jitter filter

TOUCH_PAD_FILTER_MAX¶

enum touch_smooth_mode_t¶

Level of filter applied on the original data against large noise interference.

Note: On ESP32S2. There is an error in the IIR calculation. The magnitude of the error is twice the filter coefficient. So please select a smaller filter coefficient on the basis of meeting the filtering requirements. Recommended filter coefficient selection IIR_2.

Values:

TOUCH_PAD_SMOOTH_OFF = 0¶: No filtering of raw data.

TOUCH_PAD_SMOOTH_IIR_2 = 1¶: Filter the raw data. The coefficient is 2 (Typical value).

TOUCH_PAD_SMOOTH_IIR_4 = 2¶: Filter the raw data. The coefficient is 4.

TOUCH_PAD_SMOOTH_IIR_8 = 3¶: Filter the raw data. The coefficient is 8.

TOUCH_PAD_SMOOTH_MAX¶

Provide feedback about this document