SDMMC Host Driver

Overview

ESP32’s SDMMC host peripheral has two slots:

Pin mappings of these slots are given in the table below.

Signal

Slot 0

Slot 1

CMD

GPIO11

GPIO15

CLK

GPIO6

GPIO14

D0

GPIO7

GPIO2

D1

GPIO8

GPIO4

D2

GPIO9

GPIO12

D3

GPIO10

GPIO13

D4

GPIO16

D5

GPIO17

D6

GPIO5

D7

GPIO18

CD

any input via GPIO matrix

WP

any input via GPIO matrix

The Card Detect and Write Protect signals can be routed to arbitrary pins using the GPIO matrix. To reserve the pins, set the gpio_cd and gpio_wp members of the sdmmc_slot_config_t structure before calling sdmmc_host_init_slot(). Please note that it is not advised to specify a Card Detect pin when working with SDIO cards, because the card detect signal in ESP32 can also trigger SDIO slave interrupt.

Warning

Pins used by Slot 0 (HS1_*) are also used to connect the SPI flash chip in ESP32-WROOM and ESP32-WROVER modules. These pins cannot be shared between an SD card and SPI flash. If you need to use Slot 0, connect SPI flash to different pins and set eFuses accordingly.

Supported Speed Modes

SDMMC Host driver supports the following speed modes:

  • Default Speed (20 MHz), 4-line/1-line (with SD cards), and 8-line (with 3.3 V eMMC)

  • High Speed (40 MHz), 4-line/1-line (with SD cards), and 8-line (with 3.3 V eMMC)

  • High Speed DDR (40 MHz), 4-line (with 3.3 V eMMC)

Speed modes not supported at present:

  • High Speed DDR mode, 8-line eMMC

  • UHS-I 1.8 V modes, 4-line SD cards

Using the SDMMC Host Driver

Of all the functions listed below, only the following ones will be used directly by most applications:

Other functions, such as the ones given below, will be called by the SD/MMC protocol layer via function pointers in the sdmmc_host_t structure:

Configuring Bus Width and Frequency

With the default initializers for sdmmc_host_t and sdmmc_slot_config_t (SDMMC_HOST_DEFAULT and SDMMC_SLOT_CONFIG_DEFAULT), SDMMC Host driver will attempt to use the widest bus supported by the card (4 lines for SD, 8 lines for eMMC) and the frequency of 20 MHz.

In the designs where communication at 40 MHz frequency can be achieved, it is possible to increase the bus frequency by changing the max_freq_khz field of sdmmc_host_t:

sdmmc_host_t host = SDMMC_HOST_DEFAULT();
host.max_freq_khz = SDMMC_FREQ_HIGHSPEED;

To configure the bus width, set the width field of sdmmc_slot_config_t. For example, to set 1-line mode:

sdmmc_slot_config_t slot = SDMMC_SLOT_CONFIG_DEFAULT();
slot.width = 1;

See also

See SD/SDIO/MMC Driver for the higher level driver which implements the protocol layer.

See SD SPI Host Driver for a similar driver which uses the SPI controller and is limited to SD protocol’s SPI mode.

See SD Pull-up Requirements for pullup support and compatibilities of modules and development kits.

API Reference

Functions

esp_err_t sdmmc_host_init(void)

Initialize SDMMC host peripheral.

Note

This function is not thread safe

Return

  • ESP_OK on success

  • ESP_ERR_INVALID_STATE if sdmmc_host_init was already called

  • ESP_ERR_NO_MEM if memory can not be allocated

esp_err_t sdmmc_host_init_slot(int slot, const sdmmc_slot_config_t *slot_config)

Initialize given slot of SDMMC peripheral.

On the ESP32, SDMMC peripheral has two slots:

  • Slot 0: 8-bit wide, maps to HS1_* signals in PIN MUX

  • Slot 1: 4-bit wide, maps to HS2_* signals in PIN MUX

Card detect and write protect signals can be routed to arbitrary GPIOs using GPIO matrix.

Note

This function is not thread safe

Return

  • ESP_OK on success

  • ESP_ERR_INVALID_STATE if host has not been initialized using sdmmc_host_init

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

  • slot_config: additional configuration for the slot

esp_err_t sdmmc_host_set_bus_width(int slot, size_t width)

Select bus width to be used for data transfer.

SD/MMC card must be initialized prior to this command, and a command to set bus width has to be sent to the card (e.g. SD_APP_SET_BUS_WIDTH)

Note

This function is not thread safe

Return

  • ESP_OK on success

  • ESP_ERR_INVALID_ARG if slot number or width is not valid

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

  • width: bus width (1, 4, or 8 for slot 0; 1 or 4 for slot 1)

size_t sdmmc_host_get_slot_width(int slot)

Get bus width configured in sdmmc_host_init_slot to be used for data transfer.

Return

configured bus width of the specified slot.

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

esp_err_t sdmmc_host_set_card_clk(int slot, uint32_t freq_khz)

Set card clock frequency.

Currently only integer fractions of 40MHz clock can be used. For High Speed cards, 40MHz can be used. For Default Speed cards, 20MHz can be used.

Note

This function is not thread safe

Return

  • ESP_OK on success

  • other error codes may be returned in the future

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

  • freq_khz: card clock frequency, in kHz

esp_err_t sdmmc_host_set_bus_ddr_mode(int slot, bool ddr_enabled)

Enable or disable DDR mode of SD interface.

Return

  • ESP_OK on success

  • ESP_ERR_NOT_SUPPORTED if DDR mode is not supported on this slot

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

  • ddr_enabled: enable or disable DDR mode

esp_err_t sdmmc_host_do_transaction(int slot, sdmmc_command_t *cmdinfo)

Send command to the card and get response.

This function returns when command is sent and response is received, or data is transferred, or timeout occurs.

Note

This function is not thread safe w.r.t. init/deinit functions, and bus width/clock speed configuration functions. Multiple tasks can call sdmmc_host_do_transaction as long as other sdmmc_host_* functions are not called.

Attention

Data buffer passed in cmdinfo->data must be in DMA capable memory

Return

  • ESP_OK on success

  • ESP_ERR_TIMEOUT if response or data transfer has timed out

  • ESP_ERR_INVALID_CRC if response or data transfer CRC check has failed

  • ESP_ERR_INVALID_RESPONSE if the card has sent an invalid response

  • ESP_ERR_INVALID_SIZE if the size of data transfer is not valid in SD protocol

  • ESP_ERR_INVALID_ARG if the data buffer is not in DMA capable memory

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

  • cmdinfo: pointer to structure describing command and data to transfer

esp_err_t sdmmc_host_io_int_enable(int slot)

Enable IO interrupts.

This function configures the host to accept SDIO interrupts.

Return

returns ESP_OK, other errors possible in the future

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

esp_err_t sdmmc_host_io_int_wait(int slot, TickType_t timeout_ticks)

Block until an SDIO interrupt is received, or timeout occurs.

Return

  • ESP_OK on success (interrupt received)

  • ESP_ERR_TIMEOUT if the interrupt did not occur within timeout_ticks

Parameters
  • slot: slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

  • timeout_ticks: number of RTOS ticks to wait for the interrupt

esp_err_t sdmmc_host_deinit(void)

Disable SDMMC host and release allocated resources.

Note

This function is not thread safe

Return

  • ESP_OK on success

  • ESP_ERR_INVALID_STATE if sdmmc_host_init function has not been called

esp_err_t sdmmc_host_pullup_en(int slot, int width)

Enable the pull-ups of sd pins.

Note

You should always place actual pullups on the lines instead of using this function. Internal pullup resistance are high and not sufficient, may cause instability in products. This is for debug or examples only.

Return

  • ESP_OK: if success

  • ESP_ERR_INVALID_ARG: if configured width larger than maximum the slot can support

Parameters
  • slot: Slot to use, normally set it to 1.

  • width: Bit width of your configuration, 1 or 4.

Structures

struct sdmmc_slot_config_t

Extra configuration for SDMMC peripheral slot

Public Members

gpio_num_t gpio_cd

GPIO number of card detect signal.

gpio_num_t gpio_wp

GPIO number of write protect signal.

uint8_t width

Bus width used by the slot (might be less than the max width supported)

uint32_t flags

Features used by this slot.

Macros

SDMMC_HOST_SLOT_0

SDMMC slot 0.

SDMMC_HOST_SLOT_1

SDMMC slot 1.

SDMMC_HOST_DEFAULT()

Default sdmmc_host_t structure initializer for SDMMC peripheral.

Uses SDMMC peripheral, with 4-bit mode enabled, and max frequency set to 20MHz

SDMMC_SLOT_FLAG_INTERNAL_PULLUP

Enable internal pullups on enabled pins. The internal pullups are insufficient however, please make sure external pullups are connected on the bus. This is for debug / example purpose only.

SDMMC_SLOT_NO_CD

indicates that card detect line is not used

SDMMC_SLOT_NO_WP

indicates that write protect line is not used

SDMMC_SLOT_WIDTH_DEFAULT

use the default width for the slot (8 for slot 0, 4 for slot 1)

SDMMC_SLOT_CONFIG_DEFAULT()

Macro defining default configuration of SDMMC host slot