Warning

This document is not updated for ESP32P4 yet, so some of the content may not be correct.

This warning was automatically inserted due to the source file being in the add_warnings_pages list.

USB Device Stack

[中文]

Overview

The ESP-IDF USB Device Stack (hereinafter referred to as the Device Stack) enables USB Device support on ESP32-P4. By using the Device Stack, ESP32-P4 can be programmed with any well defined USB device functions (e.g., keyboard, mouse, camera), a custom function (aka vendor-specific class), or a combination of those functions (aka a composite device).

The Device Stack is built around the TinyUSB stack, but extends TinyUSB with some minor features and modifications for better integration with ESP-IDF. The Device stack is distributed as a managed component via the ESP-IDF Component Registry.

Features

  • Multiple supported device classes (CDC, HID, MIDI, MSC)

  • Composite devices

  • Vendor specific classes

  • Maximum of 6 endpoints

    • 5 IN/OUT endpoints

    • 1 IN endpoints

  • VBUS monitoring for self-powered devices

Hardware Connection

The ESP32-P4 routes the USB D+ and D- signals to GPIOs 20 and 19 respectively. For USB device functionality, these GPIOs should be connected to the bus in some way (e.g., via a Micro-B port, USB-C port, or directly to standard-A plug).

Connection of an USB GPIOs directly to a USB standard-A plug

Note

If you are using an ESP32-P4 development board with two USB ports, the port labeled "USB" will already be connected to the D+ and D- GPIOs.

Note

Self-powered devices must also connect VBUS through a voltage divider or comparator. For more details, please refer to Self-Powered Device.

Device Stack Structure

The basis of the Device Stack is TinyUSB, where the Device Stack implements the following features on top of TinyUSB:

  • Customization of USB descriptors

  • Serial device support

  • Redirecting of standard streams through the Serial device

  • Storage Media (SPI-Flash and SD-Card) for USB Device MSC Class.

  • A task within the encapsulated device stack that handles TinyUSB servicing

Component Dependency

The Device Stack is distributed via the ESP-IDF Component Registry. Thus, to use it, please add the Device Stack component as dependency using the following command:

idf.py add-dependency esp_tinyusb

Configuration Options

Multiple aspects of the Device Stack can be configured using menuconfig. These include:

  • The verbosity of the TinyUSB's log

  • Device Stack task related options

  • Default device/string descriptor options

  • Class specific options

Descriptor Configuration

The tinyusb_config_t structure provides USB descriptor related fields that should be initialized.

The following descriptors should be initialized for both full-speed and high-speed devices:

  • device_descriptor

  • string_descriptor

Full-speed devices should initialize the following field to provide their configuration descriptor:

  • configuration_descriptor

High-speed devices should initialize the following fields to provide configuration descriptors at each speed:

  • fs_configuration_descriptor

  • hs_configuration_descriptor

  • qualifier_descriptor

Note

When Device Stack supports high-speed, both fs_configuration_descriptor and hs_configuration_descriptor should be present to comply with usb2.0 specification.

The Device Stack will instantiate a USB device based on the descriptors provided in the fields described above when tinyusb_driver_install() is called.

The Device Stack also provides default descriptors that can be installed by setting the corresponding field in tinyusb_driver_install() to NULL. Default descriptors include:

  • Default device descriptor: Enabled by setting device_descriptor to NULL. Default device descriptor will use the values set by the corresponding menuconfig options (e.g., PID, VID, bcdDevice etc).

  • Default string descriptor: Enabled by setting string_descriptor to NULL. Default string descriptors will use the value set by corresponding menuconfig options (e.g., manufacturer, product, and serial string descriptor options).

  • Default configuration descriptor. Some classes that rarely require custom configuration (such as CDC and MSC) will provide default configuration descriptors. These can be enabled by setting associated configuration descriptor field to NULL:

    • configuration_descriptor full-speed descriptor for full-speed devices only

    • fs_configuration_descriptor full-speed descriptor for high-speed devices

    • hs_configuration_descriptor high-speed descriptor for high-speed devices

Note

Backward compatibility: when Device Stack supports high-speed, field configuration_descriptor could be used instead of fs_configuration_descriptor for full-speed configuration descriptor.

Installation

To install the Device Stack, please call tinyusb_driver_install(). The Device Stack's configuration is specified in a tinyusb_config_t structure that is passed as an argument to tinyusb_driver_install().

Note

The tinyusb_config_t structure can be zero-initialized (e.g., const tinyusb_config_t tusb_cfg = { 0 };) or partially (as shown below). For any member that is initialized to 0 or NULL, the stack uses its default configuration values for that member, see example below.

const tinyusb_config_t partial_init = {
    .device_descriptor = NULL,  // Use the default device descriptor specified in Menuconfig
    .string_descriptor = NULL,  // Use the default string descriptors specified in Menuconfig
    .external_phy = false,      // Use internal USB PHY
#if (TUD_OPT_HIGH_SPEED)
    .fs_configuration_descriptor = NULL, // Use the default full-speed configuration descriptor according to settings in Menuconfig
    .hs_configuration_descriptor = NULL, // Use the default high-ppeed configuration descriptor according to settings in Menuconfig
    .qualifier_descriptor = NULL,  // Use the default qualifier descriptor, with values from default device descriptor
#else
    .configuration_descriptor = NULL,   // Use the default configuration descriptor according to settings in Menuconfig
#endif // TUD_OPT_HIGH_SPEED

};

Self-Powered Device

USB specification mandates self-powered devices to monitor voltage levels on USB's VBUS signal. As opposed to bus-powered devices, a self-powered device can be fully functional even without a USB connection. The self-powered device detects connection and disconnection events by monitoring the VBUS voltage level. VBUS is considered valid if it rises above 4.75 V and invalid if it falls below 4.35 V.

On the ESP32-P4, this will require using a GPIO to act as a voltage sensing pin to detect when VBUS goes above/below the prescribed thresholds. However, ESP32-P4 pins are 3.3 V tolerant. Thus, even if VBUS rises/falls above/below the thresholds mentioned above, it would still appear as a logic HIGH to the ESP32-P4. Thus, in order to detect the VBUS valid condition, users can do one of the following:

  • Connect VBUS to a voltage comparator chip/circuit that detects the thresholds described above (i.e., 4.35 V and 4.75 V), and outputs a 3.3 V logic level to the ESP32-P4 indicating whether VBUS is valid or not.

  • Use a resistor voltage divider that outputs (0.75 x Vdd) if VBUS is 4.4 V (see figure below).

Note

In either case, the voltage on the sensing pin must be logic low within 3 ms after the device is unplugged from the USB host.

Simple voltage divider for VBUS monitoring

Simple voltage divider for VBUS monitoring

To use this feature, in tinyusb_config_t, you must set self_powered to true and vbus_monitor_io to GPIO number that is used for VBUS monitoring.

USB Serial Device (CDC-ACM)

If the CDC option is enabled in Menuconfig, the USB Serial Device can be initialized with tusb_cdc_acm_init() according to the settings from tinyusb_config_cdcacm_t, see example below.

const tinyusb_config_cdcacm_t acm_cfg = {
    .usb_dev = TINYUSB_USBDEV_0,
    .cdc_port = TINYUSB_CDC_ACM_0,
    .rx_unread_buf_sz = 64,
    .callback_rx = NULL,
    .callback_rx_wanted_char = NULL,
    .callback_line_state_changed = NULL,
    .callback_line_coding_changed = NULL
};
tusb_cdc_acm_init(&acm_cfg);

To specify callbacks, you can either set the pointer to your tusb_cdcacm_callback_t function in the configuration structure or call tinyusb_cdcacm_register_callback() after initialization.

USB Serial Console

The USB Serial Device allows the redirection of all standard input/output streams (stdin, stdout, stderr) to USB. Thus, calling standard library input/output functions such as printf() will result into the data being sent/received over USB instead of UART.

Users should call esp_tusb_init_console() to switch the standard input/output streams to USB, and esp_tusb_deinit_console() to switch them back to UART.

USB Mass Storage Device (MSC)

If the MSC CONFIG_TINYUSB_MSC_ENABLED option is enabled in Menuconfig, the ESP Chip can be used as USB MSC Device. The storage media (SPI-Flash or SD-Card) can be initialized as shown below.

  • SPI-Flash

static esp_err_t storage_init_spiflash(wl_handle_t *wl_handle)
{
    ***
    esp_partition_t *data_partition = esp_partition_find_first(ESP_PARTITION_TYPE_DATA, ESP_PARTITION_SUBTYPE_DATA_FAT, NULL);
    ***
    wl_mount(data_partition, wl_handle);
    ***
}
storage_init_spiflash(&wl_handle);

const tinyusb_msc_spiflash_config_t config_spi = {
    .wl_handle = wl_handle
};
tinyusb_msc_storage_init_spiflash(&config_spi);
  • SD-Card

static esp_err_t storage_init_sdmmc(sdmmc_card_t **card)
{
    ***
    sdmmc_host_t host = SDMMC_HOST_DEFAULT();
    sdmmc_slot_config_t slot_config = SDMMC_SLOT_CONFIG_DEFAULT();
    // For SD Card, set bus width to use

    slot_config.width = 4;
    slot_config.clk = CONFIG_EXAMPLE_PIN_CLK;
    slot_config.cmd = CONFIG_EXAMPLE_PIN_CMD;
    slot_config.d0 = CONFIG_EXAMPLE_PIN_D0;
    slot_config.d1 = CONFIG_EXAMPLE_PIN_D1;
    slot_config.d2 = CONFIG_EXAMPLE_PIN_D2;
    slot_config.d3 = CONFIG_EXAMPLE_PIN_D3;
    slot_config.flags |= SDMMC_SLOT_FLAG_INTERNAL_PULLUP;

    sd_card = (sdmmc_card_t *)malloc(sizeof(sdmmc_card_t));
    (*host.init)();
    sdmmc_host_init_slot(host.slot, (const sdmmc_slot_config_t *) &slot_config);
    sdmmc_card_init(&host, sd_card);
    ***
}
storage_init_sdmmc(&card);

const tinyusb_msc_sdmmc_config_t config_sdmmc = {
    .card = card
};
tinyusb_msc_storage_init_sdmmc(&config_sdmmc);

Application Examples

The table below describes the code examples available in the directory peripherals/usb/device:

Code Example

Description

peripherals/usb/device/tusb_console

How to set up ESP32-P4 chip to get log output via Serial Device connection

peripherals/usb/device/tusb_serial_device

How to set up ESP32-P4 chip to work as a USB Serial Device

peripherals/usb/device/tusb_midi

How to set up ESP32-P4 chip to work as a USB MIDI Device

peripherals/usb/device/tusb_hid

How to set up ESP32-P4 chip to work as a USB Human Interface Device

peripherals/usb/device/tusb_msc

How to set up ESP32-P4 chip to work as a USB Mass Storage Device

peripherals/usb/device/tusb_composite_msc_serialdevice

How to set up ESP32-P4 chip to work as a Composite USB Device (MSC + CDC)