ESP-WROVER-KIT V3 Getting Started Guide

This user guide shows how to get started with the ESP-WROVER-KIT V3 development board including description of its functionality and configuration options. For descriptions of other versions of the ESP-WROVER-KIT check ESP32 H/W 硬件参考.

If you would like to start using this board right now, go directly to the 应用程序开发 section.

What You Need

  • 1 × ESP-WROVER-KIT V3 board

  • 1 x Micro USB 2.0 Cable, Type A to Micro B

  • 1 × PC loaded with Windows, Linux or Mac OS

Overview

The ESP-WROVER-KIT is a development board built around the ESP32 and produced by Espressif. This board is compatible with multiple ESP32 modules, including the ESP32-WROOM-32 and ESP32-WROVER. The ESP-WROVER-KIT features support for an LCD and MicroSD card. The I/O pins have been broken out from the ESP32 module for easy extension. The board carries an advanced multi-protocol USB bridge (the FTDI FT2232HL), enabling developers to use JTAG directly to debug the ESP32 through the USB interface. The development board makes secondary development easy and cost-effective.

注解

ESP-WROVER-KIT V3 integrates the ESP32-WROVER module by default.

Functionality Overview

The block diagram below illustrates the ESP-WROVER-KIT’s main components and their interconnections.

ESP-WROVER-KIT block diagram

ESP-WROVER-KIT block diagram

Functional Description

The following lists and figures describe the key components, interfaces, and controls of ESP-WROVER-KIT board.

32.768 kHz

An external precision 32.768 kHz crystal oscillator provides a low-power consumption clock used during Deep-Sleep mode.

0R

A zero Ohm resistor intended as a placeholder for a current shunt. May be desoldered or replaced with a current shunt to facilitate measurement of current required by ESP32 module depending on power mode.

ESP32 Module

ESP-WROVER-KIT is compatible with both the ESP32-WROOM-32 and the ESP32-WROVER. The ESP32-WROVER module features all the functions of ESP32-WROOM-32 and integrates an external 32-Mbit PSRAM for flexible extended storage and data processing capabilities.

注解

GPIO16 and GPIO17 are used as the CS and clock signal for PSRAM. To ensure reliable performance, the two GPIOs are not broken out.

FT2232

The FT2232 chip is a multi-protocol USB-to-serial bridge. Users can control and program the FT2232 chip through the USB interface to establish communication with ESP32. The FT2232 chip also features USB-to-JTAG interface. USB-to-JTAG is available on channel A of the FT2232, whilst USB-to-serial is on channel B. The embedded FT2232 chip is one of the distinguishing features of the ESP-WROVER-KIT. It enhances users’ convenience in terms of application development and debugging. In addition, users need not purchase a JTAG debugger separately, which reduces the development cost, see ESP-WROVER-KIT V3 schematic.

UART

Serial port: the serial TX/RX signals on the FT2232HL and the ESP32 are broken out to each side of JP11. By default, the two signals are connected with jumpers. To use the ESP32 module serial interface only, the jumpers may be removed and the module can be connected to another external serial device.

SPI

The SPI interface is used by the ESP32 to access flash and PSRAM memories within the module itself. To interface with another SPI device, an extra CS signal is needed. Please note that the voltage level on this interface depends on the module used (e.g 1.8V and 3.3V for the ESP32-WROVER and ESP32-WROOM-32 respectively).

CTS/RTS

Serial port flow control signals: the pins are not connected to the circuitry by default. To enable them, respective pins of JP14 must be shorted with jumpers.

JTAG

JTAG interface: the JTAG signals on FT2232HL and ESP32 are broken out to the two sides of JP8. By default, the two signals are disconnected. To enable JTAG, shorting jumpers are required on the signals.

EN

Reset button: pressing this button resets the system.

Boot

Download button: holding down the Boot button and pressing the EN button initiates the firmware download mode. Then user can download firmware through the serial port.

USB

USB interface. It functions as the power supply for the board and the communication interface between PC and ESP32 module.

Power Select

Power supply selection interface: the ESP-WROVER-KIT can be powered through the USB interface or the 5V Input interface. The user can select the power supply with a jumper. More details can be found in section Setup Options, jumper header JP7.

Power Key

Power on/off button: toggling to the right powers the board on; toggling to the left powers the board off.

5V Input

The 5V power supply interface is used as a backup power supply in case of full-load operation.

LDO

NCP1117(1A). 5V-to-3.3V LDO. (There is an alternative pin-compatible LDO — LM317DCY, with an output current of up to 1.5A). NCP1117 can provide a maximum current of 1A. The LDO solutions are available with both fixed output voltage and variable output voltage. For details please refer to ESP-WROVER-KIT V3 schematic.

Camera

Camera interface: a standard OV7670 camera module is supported.

RGB

Red, green and blue (RGB) light emitting diodes (LEDs), which may be controlled by pulse width modulation (PWM).

I/O

All the pins on the ESP32 module are led out to the pin headers on the ESP-WROVER-KIT. Users can program ESP32 to enable multiple functions such as PWM, ADC, DAC, I2C, I2S, SPI, etc.

Micro SD Card

Develop applications that access Micro SD card for data storage and retrieval.

LCD

ESP-WROVER-KIT supports mounting and interfacing a 3.2” SPI (standard 4-wire Serial Peripheral Interface) LCD, as shown on figure ESP-WROVER-KIT board layout - back.

ESP-WROVER-KIT board layout - front

ESP-WROVER-KIT board layout - front

ESP-WROVER-KIT board layout - back

ESP-WROVER-KIT board layout - back

Setup Options

There are five jumper headers available to set up the board functionality. Typical options to select from are listed in table below.

Header

Jumper Setting

Description of Functionality

JP7

jp7-ext_5v

Power ESP-WROVER-KIT board from an external power supply

JP7

jp7-usb_5v

Power ESP-WROVER-KIT board from an USB port

JP8

jp8

Enable JTAG functionality

JP11

jp11-rx-tx

Enable UART communication

JP14

jp14

Enable RTS/CTS flow control for serial communication

Allocation of ESP32 Pins

Several pins / terminals of ESP32 module are allocated to the on board hardware. Some of them, like GPIO0 or GPIO2, have multiple functions. If certain hardware is not installed, e.g. nothing is plugged in to the Camera / JP4 header, then selected GPIOs may be used for other purposes.

Main I/O Connector / JP1

The JP1 connector is shown in two columns in the middle under “I/O” headers. The two columns “Shared With” outside, describe where else on the board certain GPIO is used.

Shared With

I/O

I/O

Shared With

3.3V

GND

NC/XTAL

IO32

IO33

NC/XTAL

JTAG, MicroSD

IO12

IO13

JTAG, MicroSD

JTAG, MicroSD

IO14

IO27

Camera

Camera

IO26

IO25

Camera, LCD

Camera

IO35

IO34

Camera

Camera

IO39

IO36

Camera

JTAG

EN

IO23

Camera, LCD

Camera, LCD

IO22

IO21

Camera, LCD, MicroSD

Camera, LCD

IO19

IO18

Camera, LCD

Camera, LCD

IO5

IO17

PSRAM

PSRAM

IO16

IO4

LED, Camera, MicroSD

Camera, LED, Boot

IO0

IO2

LED, MicroSD

JTAG, MicroSD

IO15

5V

Legend:

32.768 kHz Oscillator

ESP32 Pin

1

GPIO32

2

GPIO33

注解

As GPIO32 and GPIO33 are connected to the oscillator, they are not connected to JP1 I/O expansion connector to maintain signal integrity. This allocation may be changed from oscillator to JP1 by desoldering the 0R resistors from positions R11 / R23 and installing them in positions R12 / R24.

SPI Flash / JP13

ESP32 Pin

1

CLK / GPIO6

2

SD0 / GPIO7

3

SD1 / GPIO8

4

SD2 / GPIO9

5

SD3 / GPIO10

6

CMD / GPIO11

重要

The module’s flash bus is connected to the pin header JP13 through 0-Ohm resistors R140 ~ R145. If the flash frequency needs to operate at 80 MHz for reasons such as improving the integrity of bus signals, it is recommended that resistors R140 ~ R145 be desoldered. At this point, the module’s flash bus is disconnected with the pin header JP13.

JTAG / JP8

ESP32 Pin

JTAG Signal

1

EN

TRST_N

2

MTDO / GPIO15

TDO

3

MTDI / GPIO12

TDI

4

MTCK / GPIO13

TCK

5

MTMS / GPIO14

TMS

Camera / JP4

ESP32 Pin

Camera Signal

1

n/a

3.3V

2

n/a

Ground

3

GPIO27

SIO_C / SCCB Clock

4

GPIO26

SIO_D / SCCB Data

5

GPIO25

VSYNC / Vertical Sync

6

GPIO23

HREF / Horizontal Reference

7

GPIO22

PCLK / Pixel Clock

8

GPIO21

XCLK / System Clock

9

GPIO35

D7 / Pixel Data Bit 7

10

GPIO34

D6 / Pixel Data Bit 6

11

GPIO39

D5 / Pixel Data Bit 5

12

GPIO36

D4 / Pixel Data Bit 4

13

GPIO19

D3 / Pixel Data Bit 3

14

GPIO18

D2 / Pixel Data Bit 2

15

GPIO5

D1 / Pixel Data Bit 1

16

GPIO4

D0 / Pixel Data Bit 0

17

GPIO0

RESET / Camera Reset

18

n/a

PWDN / Camera Power Down

RGB LED

ESP32 Pin

RGB LED

1

GPIO0

Red

2

GPIO2

Green

3

GPIO4

Blue

MicroSD Card / J4

ESP32 Pin

MicroSD Signal

1

MTDI / GPIO12

DATA2

2

MTCK / GPIO13

CD / DATA3

3

MTDO / GPIO15

CMD

4

MTMS / GPIO14

CLK

5

GPIO2

DATA0

6

GPIO4

DATA1

7

GPIO21

CD

LCD / U5

ESP32 Pin

LCD Signal

1

GPIO18

RESET

2

GPIO19

SCL

3

GPIO21

D/C

4

GPIO22

CS

5

GPIO23

SDA

6

GPIO25

SDO

7

GPIO5

Backlight

Start Application Development

Before powering up the ESP-WROVER-KIT, please make sure that the board has been received in good condition with no obvious signs of damage.

Initial Setup

Select the source of power supply for the board by setting jumper JP7. The options are either USB port or an external power supply. For this application selection of USB port is sufficient. Enable UART communication by installing jumpers on JP11. Both selections are shown in table below.

Power up from USB port

Enable UART communication

jp7-usb_5v

jp11-rx-tx

Do not install any other jumpers.

Now to Development

To start development of applications for ESP-WROVER-KIT, proceed to the 快速入门 section which will walk you through the following steps:

  • 设置工具链 in your PC to develop applications for ESP32 in C language

  • 连接 the module to the PC and verify if it is accessible

  • 编译和烧写 an example application to the ESP32

  • 监视器 instantly what the application is doing