Wireless-Tag TINY Boards
The Wireless-Tag TINY family includes compact ESP32-C3, ESP32-C5, ESP32-P4, and ESP32-S31 development boards. These board definitions provide the default GPIO assignments, addressable RGB LED, boot button, memory settings, and upload options. Board-specific display, camera, storage, and wireless functionality can require additional drivers and hardware configuration.
Board Selection
Board |
Target |
CPU |
Flash default |
PSRAM default |
|---|---|---|---|---|
WT9932C3-TINY |
ESP32-C3 |
160 MHz |
4 MB (verify module) |
Disabled |
WT9932C5-TINY |
ESP32-C5 |
240 MHz |
4 MB (verify module) |
Disabled |
WT9932P4-TINY |
ESP32-P4 v1.x |
360 MHz |
16 MB |
Enabled |
WT9932P4X-TINY |
ESP32-P4 v3.x |
400 MHz |
16 MB |
Enabled |
WT9932P4C61-TINY |
ESP32-P4 v3.x |
400 MHz |
16 MB |
Enabled |
WT9932S31-TINY |
ESP32-S31 |
320 MHz |
16 MB |
Enabled (OPI) |
The ESP32-C3 and ESP32-C5 module memory capacities are not specified by the board support sources. Their 4 MB setting is a software default, not a claim about every module fitted to these boards. Check the module marking and detected flash size, then choose the matching 2, 4, 8, or 16 MB Flash Size option. Each option selects a matching partition table. PSRAM is not enabled for these boards.
WT9932P4-TINY, WT9932P4X-TINY, WT9932P4C61-TINY, and WT9932S31-TINY use the existing 16 MB partition table. No separate board-manager package or modified core is required by these definitions.
ESP32-P4 Revisions
WT9932P4-TINY and WT9932P4X-TINY have similar peripheral wiring but require
different SDK variants. WT9932P4-TINY uses esp32p4_es at 360 MHz, and
WT9932P4X-TINY uses esp32p4 at 400 MHz. The vendor identifies the newer
module by an X suffix on its shield marking. The supported minimum silicon
revision also depends on the SDK bundled with the selected Arduino core.
Select the board that matches the fitted module. A board menu or a compile-time
macro selects the build configuration; it does not detect the silicon revision.
ESP.getChipRevision() reports the runtime silicon revision as
major * 100 + minor.
The WT9932P4C61-TINY board definition targets the newer ESP32-P4 host in the board’s Wireless-Tag module. It does not include an unverified legacy-revision option.
Default Pins
GPIO numbers are used directly. The UART, I2C, and SPI assignments below are software defaults; they do not imply matching labels on every expansion connector. Check the board pinout before connecting peripherals.
Board |
RGB / button |
TX / RX |
SDA / SCL |
SS / MOSI / MISO / SCK |
|---|---|---|---|---|
WT9932C3-TINY |
6 / 9 |
21 / 20 |
4 / 5 |
7 / 10 / 3 / 2 |
WT9932C5-TINY |
6 / 28 |
11 / 12 |
0 / 1 |
7 / 8 / 9 / 10 |
WT9932P4-TINY, WT9932P4X-TINY, WT9932P4C61-TINY |
51 / 35 |
37 / 38 |
7 / 8 |
5 / 32 / 33 / 36 |
WT9932S31-TINY |
19 / 61 |
58 / 59 |
2 / 3 |
37 / 38 / 39 / 40 |
The button is active low. WT_BUTTON_PIN and WT_RGB_PIN expose its GPIO
and the addressable LED GPIO. LED_BUILTIN and RGB_BUILTIN use the core’s
virtual RGB pin convention so that the standard Blink sketch works with the
addressable LED. Use WT_RGB_PIN when an API requires the physical GPIO.
Upload and USB
WT9932C3-TINY and WT9932C5-TINY use their USB-to-UART bridge by default, with USB CDC on boot disabled. Select the bridge’s serial port for uploading and monitoring.
WT9932P4-TINY, WT9932P4X-TINY, WT9932P4C61-TINY, and WT9932S31-TINY default to Hardware CDC and JTAG, with USB CDC on boot enabled. For the USB-OTG connection, select USB-OTG under USB Mode and USB-OTG CDC under Upload Mode, and enable USB CDC on boot. Use the connector that matches the selected mode. Erase All Flash Before Sketch Upload is disabled by default on every board.
Peripheral Boundaries
The microSD interface on WT9932P4-TINY and WT9932P4X-TINY uses GPIO43/44 for clock/command and GPIO39-42 for the four data signals. Its GPIO bank uses the 3.3 V VO4 supply (LDO channel 4). Both variants provide the corresponding SDMMC and automatic IO-rail definitions.
WT9932P4C61-TINY exposes its microSD signals through WT_SD_SPI_* for use
with the SPI SD library. Its card supply is external, so it does not use the
SDMMC power-channel definition provided for WT9932P4-TINY and WT9932P4X-TINY.
The Wireless-Tag module on WT9932P4C61-TINY connects an ESP32-P4 host to an
ESP32-C61 coprocessor over a 4-bit SDIO bus. Arduino sketches run on the
ESP32-P4 host, and the ESP32-C61 runs ESP-Hosted firmware. The board
definition exposes the SDIO wiring through WT_HOSTED_*. ESP-Hosted
operation requires host configuration and compatible ESP32-C61 firmware.
The WT9932S31-TINY microSD signals use GPIO24/25 for clock/command and GPIO20-23 for data. Their supply is 1.8 V on LDO channel 1. This variant does not enable generic SDMMC power defaults for that board. Card operation requires a driver and power setup that preserve the 1.8 V pad supply. That setup is outside this board definition’s scope.
Display and camera constants describe board wiring and available connectors. They do not install display, touch, CSI, DSI, or DVP drivers. Ethernet and audio definitions from Espressif evaluation boards are not applicable to these TINY boards.