I2C Driver

[中文]

Overview

I2C is a serial, synchronous, half-duplex communication protocol that allows co-existence of multiple masters and slaves on the same bus. The I2C bus consists of two lines: serial data line (SDA) and serial clock (SCL). Both lines require pull-up resistors.

With such advantages as simplicity and low manufacturing cost, I2C is mostly used for communication of low-speed peripheral devices over short distances (within one foot).

ESP32 has two I2C controllers (also referred to as ports) which are responsible for handling communications on the I2C bus. Each I2C controller can operate as master or slave. As an example, one controller can act as a master and the other as a slave at the same time.

Driver Features

I2C driver governs communications of devices over the I2C bus. The driver supports the following features:

  • Reading and writing bytes in Master mode

  • Slave mode

  • Reading and writing to registers which are in turn read/written by the master

Driver Usage

The following sections describe typical steps of configuring and operating the I2C driver:

  1. Configuration - set the initialization parameters (master or slave mode, GPIO pins for SDA and SCL, clock speed, etc.)

  2. Install Driver- activate the driver on one of the two I2C controllers as a master or slave

  3. Depending on whether you configure the driver for a master or slave, choose the appropriate item

    1. Communication as Master - handle communications (master)

    2. Communication as Slave - respond to messages from the master (slave)

  4. Interrupt Handling - configure and service I2C interrupts

  5. Customized Configuration - adjust default I2C communication parameters (timings, bit order, etc.)

  6. Error Handling - how to recognize and handle driver configuration and communication errors

  7. Delete Driver- release resources used by the I2C driver when communication ends

Configuration

To establish I2C communication, start by configuring the driver. This is done by setting the parameters of the structure i2c_config_t:

  • Set I2C mode of operation - slave or master from i2c_mode_t

  • Configure communication pins

    • Assign GPIO pins for SDA and SCL signals

    • Set whether to enable ESP32’s internal pull-ups

  • (Master only) Set I2C clock speed

  • (Slave only) Configure the following

    • Whether to enable 10 bit address mode

    • Define slave address

After that, initialize the configuration for a given I2C port. For this, call the function i2c_param_config() and pass to it the port number and the structure i2c_config_t.

Configuration example (master):

int i2c_master_port = 0;
i2c_config_t conf = {
    .mode = I2C_MODE_MASTER,
    .sda_io_num = I2C_MASTER_SDA_IO,         // select GPIO specific to your project
    .sda_pullup_en = GPIO_PULLUP_ENABLE,
    .scl_io_num = I2C_MASTER_SCL_IO,         // select GPIO specific to your project
    .scl_pullup_en = GPIO_PULLUP_ENABLE,
    .master.clk_speed = I2C_MASTER_FREQ_HZ,  // select frequency specific to your project
    // .clk_flags = 0,          /*!< Optional, you can use I2C_SCLK_SRC_FLAG_* flags to choose i2c source clock here. */
};

Configuration example (slave):

int i2c_slave_port = I2C_SLAVE_NUM;
i2c_config_t conf_slave = {
    .sda_io_num = I2C_SLAVE_SDA_IO,          // select GPIO specific to your project
    .sda_pullup_en = GPIO_PULLUP_ENABLE,
    .scl_io_num = I2C_SLAVE_SCL_IO,          // select GPIO specific to your project
    .scl_pullup_en = GPIO_PULLUP_ENABLE,
    .mode = I2C_MODE_SLAVE,
    .slave.addr_10bit_en = 0,
    .slave.slave_addr = ESP_SLAVE_ADDR,      // address of your project
};

At this stage, i2c_param_config() also sets a few other I2C configuration parameters to default values that are defined by the I2C specification. For more details on the values and how to modify them, see Customized Configuration.

Source Clock Configuration

Clock sources allocator is added for supporting different clock sources (Master only). The clock allocator will choose one clock source that meets all the requirements of frequency and capability (as requested in i2c_config_t::clk_flags).

When i2c_config_t::clk_flags is 0, the clock allocator will select only according to the desired frequency. If no special capabilities are needed, such as APB, you can configure the clock allocator to select the source clock only according to the desired frequency. For this, set i2c_config_t::clk_flags to 0. For clock characteristics, see the table below.

Note

A clock is not a valid option, if it doesn’t meet the requested capabilities, i.e. any bit of requested capabilities (clk_flags) is 0 in the clock’s capabilities.

Characteristics of ESP32 clock sources

Clock name

Clock frequency

MAX freq for SCL

Clock capabilities

APB clock

80 MHz

4 MHz

/

Explanations for i2c_config_t::clk_flags are as follows:

  1. I2C_SCLK_SRC_FLAG_AWARE_DFS: Clock’s baud rate will not change while APB clock is changing.

  2. I2C_SCLK_SRC_FLAG_LIGHT_SLEEP: It supports Light-sleep mode, which APB clock cannot do.

  3. Some flags may not be supported on ESP32, reading technical reference manual before using it.

Note

The clock frequency of SCL in master mode should not be lager than max frequency for SCL mentioned in the table above.

Note

The clock frequency of SCL will be influenced by the pull-up resistors and wire capacitance (or might slave capacitance) together. Therefore, users need to choose correct pull-up resistors by themselves to make the frequency accurate. It is recommended by I2C protocol that the pull-up resistors commonly range from 1KOhms to 10KOhms, but different frequencies need different resistors.

Generally speaking, the higher frequency is selected, the smaller resistor should be used (but not less than 1KOhms). This is because high resistor will decline the current, which will lengthen the rising time and reduce the frequency. Usually, range 2KOhms to 5KOhms is what we recommend, but users also might need to make some adjustment depends on their reality.

Install Driver

After the I2C driver is configured, install it by calling the function i2c_driver_install() with the following parameters:

  • Port number, one of the two port numbers from i2c_port_t

  • Master or slave, selected from i2c_mode_t

  • (Slave only) Size of buffers to allocate for sending and receiving data. As I2C is a master-centric bus, data can only go from the slave to the master at the master’s request. Therefore, the slave will usually have a send buffer where the slave application writes data. The data remains in the send buffer to be read by the master at the master’s own discretion.

  • Flags for allocating the interrupt (see ESP_INTR_FLAG_* values in esp_system/include/esp_intr_alloc.h)

Communication as Master

After installing the I2C driver, ESP32 is ready to communicate with other I2C devices.

ESP32’s I2C controller operating as master is responsible for establishing communication with I2C slave devices and sending commands to trigger a slave to action, for example, to take a measurement and send the readings back to the master.

For better process organization, the driver provides a container, called a “command link”, that should be populated with a sequence of commands and then passed to the I2C controller for execution.

Master Write

The example below shows how to build a command link for an I2C master to send n bytes to a slave.

I2C command link - master write example

The following describes how a command link for a “master write” is set up and what comes inside:

  1. Create a command link with i2c_cmd_link_create().

    Then, populate it with the series of data to be sent to the slave:

    1. Start bit - i2c_master_start()

    2. Slave address - i2c_master_write_byte(). The single byte address is provided as an argument of this function call.

    3. Data - One or more bytes as an argument of i2c_master_write()

    4. Stop bit - i2c_master_stop()

    Both functions i2c_master_write_byte() and i2c_master_write() have an additional argument specifying whether the master should ensure that it has received the ACK bit.

  2. Trigger the execution of the command link by I2C controller by calling i2c_master_cmd_begin(). Once the execution is triggered, the command link cannot be modified.

  3. After the commands are transmitted, release the resources used by the command link by calling i2c_cmd_link_delete().

Master Read

The example below shows how to build a command link for an I2C master to read n bytes from a slave.

I2C command link - master read example

Compared to writing data, the command link is populated in Step 4 not with i2c_master_write... functions but with i2c_master_read_byte() and / or i2c_master_read(). Also, the last read in Step 5 is configured so that the master does not provide the ACK bit.

Indicating Write or Read

After sending a slave address (see Step 3 on both diagrams above), the master either writes or reads from the slave.

The information on what the master will actually do is hidden in the least significant bit of the slave’s address.

For this reason, the command link sent by the master to write data to the slave contains the address (ESP_SLAVE_ADDR << 1) | I2C_MASTER_WRITE and looks as follows:

i2c_master_write_byte(cmd, (ESP_SLAVE_ADDR << 1) | I2C_MASTER_WRITE, ACK_EN);

Likewise, the command link to read from the slave looks as follows:

i2c_master_write_byte(cmd, (ESP_SLAVE_ADDR << 1) | I2C_MASTER_READ, ACK_EN);

Communication as Slave

After installing the I2C driver, ESP32 is ready to communicate with other I2C devices.

The API provides the following functions for slaves

  • i2c_slave_read_buffer()

    Whenever the master writes data to the slave, the slave will automatically store it in the receive buffer. This allows the slave application to call the function i2c_slave_read_buffer() at its own discretion. This function also has a parameter to specify block time if no data is in the receive buffer. This will allow the slave application to wait with a specified timeout for data to arrive to the buffer.

  • i2c_slave_write_buffer()

    The send buffer is used to store all the data that the slave wants to send to the master in FIFO order. The data stays there until the master requests for it. The function i2c_slave_write_buffer() has a parameter to specify block time if the send buffer is full. This will allow the slave application to wait with a specified timeout for the adequate amount of space to become available in the send buffer.

A code example showing how to use these functions can be found in peripherals/i2c.

Interrupt Handling

During driver installation, an interrupt handler is installed by default. However, you can register your own interrupt handler instead of the default one by calling the function i2c_isr_register(). When implementing your own interrupt handler, refer to ESP32 Technical Reference Manual > I2C Controller (I2C) > Interrupts [PDF] for the description of interrupts triggered by the I2C controller.

To delete an interrupt handler, call i2c_isr_free().

Customized Configuration

As mentioned at the end of Section Configuration, when the function i2c_param_config() initializes the driver configuration for an I2C port, it also sets several I2C communication parameters to default values defined in the I2C specification. Some other related parameters are pre-configured in registers of the I2C controller.

All these parameters can be changed to user-defined values by calling dedicated functions given in the table below. Please note that the timing values are defined in APB clock cycles. The frequency of APB is specified in I2C_APB_CLK_FREQ.

Other Configurable I2C Communication Parameters

Parameters to Change

Function

High time and low time for SCL pulses

i2c_set_period()

SCL and SDA signal timing used during generation of start signals

i2c_set_start_timing()

SCL and SDA signal timing used during generation of stop signals

i2c_set_stop_timing()

Timing relationship between SCL and SDA signals when slave samples, as well as when master toggles

i2c_set_data_timing()

I2C timeout

i2c_set_timeout()

Choice between transmitting / receiving the LSB or MSB first, choose one of the modes defined in i2c_trans_mode_t

i2c_set_data_mode()

Each of the above functions has a _get_ counterpart to check the currently set value. For example, to check the I2C timeout value, call i2c_get_timeout().

To check the default parameter values which are set during the driver configuration process, please refer to the file driver/i2c.c and look for defines with the suffix _DEFAULT.

You can also select different pins for SDA and SCL signals and alter the configuration of pull-ups with the function i2c_set_pin(). If you want to modify already entered values, use the function i2c_param_config().

Note

ESP32’s internal pull-ups are in the range of tens of kOhm, which is, in most cases, insufficient for use as I2C pull-ups. Users are advised to use external pull-ups with values described in the I2C specification.

Error Handling

The majority of I2C driver functions either return ESP_OK on successful completion or a specific error code on failure. It is a good practice to always check the returned values and implement error handling. The driver also prints out log messages that contain error details, e.g., when checking the validity of entered configuration. For details please refer to the file driver/i2c.c and look for defines with the suffix _ERR_STR.

Use dedicated interrupts to capture communication failures. For instance, if a slave stretches the clock for too long while preparing the data to send back to master, the interrupt I2C_TIME_OUT_INT will be triggered. For detailed information, see Interrupt Handling.

In case of a communication failure, you can reset the internal hardware buffers by calling the functions i2c_reset_tx_fifo() and i2c_reset_rx_fifo() for the send and receive buffers respectively.

Delete Driver

When the I2C communication is established with the function i2c_driver_install() and is not required for some substantial amount of time, the driver may be deinitialized to release allocated resources by calling i2c_driver_delete().

Before calling i2c_driver_delete() to remove i2c driver, please make sure that all threads have stopped using the driver in any way, because this function does not guarantee thread safety.

Application Example

I2C master and slave example: peripherals/i2c.

API Reference

Functions

esp_err_t i2c_driver_install(i2c_port_t i2c_num, i2c_mode_t mode, size_t slv_rx_buf_len, size_t slv_tx_buf_len, int intr_alloc_flags)

I2C driver install.

Note

Only slave mode will use this value, driver will ignore this value in master mode.

Note

Only slave mode will use this value, driver will ignore this value in master mode.

Note

In master mode, if the cache is likely to be disabled(such as write flash) and the slave is time-sensitive, ESP_INTR_FLAG_IRAM is suggested to be used. In this case, please use the memory allocated from internal RAM in i2c read and write function, because we can not access the psram(if psram is enabled) in interrupt handle function when cache is disabled.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_FAIL Driver install error

Parameters
  • i2c_num: I2C port number

  • mode: I2C mode( master or slave )

  • slv_rx_buf_len: receiving buffer size for slave mode

Parameters
  • slv_tx_buf_len: sending buffer size for slave mode

Parameters
  • intr_alloc_flags: Flags used to allocate the interrupt. One or multiple (ORred) ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info.

esp_err_t i2c_driver_delete(i2c_port_t i2c_num)

I2C driver delete.

Note

This function does not guarantee thread safety. Please make sure that no thread will continuously hold semaphores before calling the delete function.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

esp_err_t i2c_param_config(i2c_port_t i2c_num, const i2c_config_t *i2c_conf)

I2C parameter initialization.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • i2c_conf: pointer to I2C parameter settings

esp_err_t i2c_reset_tx_fifo(i2c_port_t i2c_num)

reset I2C tx hardware fifo

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

esp_err_t i2c_reset_rx_fifo(i2c_port_t i2c_num)

reset I2C rx fifo

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

esp_err_t i2c_isr_register(i2c_port_t i2c_num, void (*fn)(void *), void *arg, int intr_alloc_flags, intr_handle_t *handle, )

I2C isr handler register.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • fn: isr handler function

  • arg: parameter for isr handler function

  • intr_alloc_flags: Flags used to allocate the interrupt. One or multiple (ORred) ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info.

  • handle: handle return from esp_intr_alloc.

esp_err_t i2c_isr_free(intr_handle_t handle)

to delete and free I2C isr.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • handle: handle of isr.

esp_err_t i2c_set_pin(i2c_port_t i2c_num, int sda_io_num, int scl_io_num, bool sda_pullup_en, bool scl_pullup_en, i2c_mode_t mode)

Configure GPIO signal for I2C sck and sda.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • sda_io_num: GPIO number for I2C sda signal

  • scl_io_num: GPIO number for I2C scl signal

  • sda_pullup_en: Whether to enable the internal pullup for sda pin

  • scl_pullup_en: Whether to enable the internal pullup for scl pin

  • mode: I2C mode

Create and init I2C command link.

Note

Before we build I2C command link, we need to call i2c_cmd_link_create() to create a command link. After we finish sending the commands, we need to call i2c_cmd_link_delete() to release and return the resources.

Return

i2c command link handler

Free I2C command link.

Note

Before we build I2C command link, we need to call i2c_cmd_link_create() to create a command link. After we finish sending the commands, we need to call i2c_cmd_link_delete() to release and return the resources.

Parameters
  • cmd_handle: I2C command handle

esp_err_t i2c_master_start(i2c_cmd_handle_t cmd_handle)

Queue command for I2C master to generate a start signal.

Note

Only call this function in I2C master mode Call i2c_master_cmd_begin() to send all queued commands

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • cmd_handle: I2C cmd link

esp_err_t i2c_master_write_byte(i2c_cmd_handle_t cmd_handle, uint8_t data, bool ack_en)

Queue command for I2C master to write one byte to I2C bus.

Note

Only call this function in I2C master mode Call i2c_master_cmd_begin() to send all queued commands

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • cmd_handle: I2C cmd link

  • data: I2C one byte command to write to bus

  • ack_en: enable ack check for master

esp_err_t i2c_master_write(i2c_cmd_handle_t cmd_handle, const uint8_t *data, size_t data_len, bool ack_en)

Queue command for I2C master to write buffer to I2C bus.

Note

Only call this function in I2C master mode Call i2c_master_cmd_begin() to send all queued commands

Note

If the psram is enabled and intr_flag is ESP_INTR_FLAG_IRAM, please use the memory allocated from internal RAM.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • cmd_handle: I2C cmd link

  • data: data to send

Parameters
  • data_len: data length

  • ack_en: enable ack check for master

esp_err_t i2c_master_read_byte(i2c_cmd_handle_t cmd_handle, uint8_t *data, i2c_ack_type_t ack)

Queue command for I2C master to read one byte from I2C bus.

Note

Only call this function in I2C master mode Call i2c_master_cmd_begin() to send all queued commands

Note

If the psram is enabled and intr_flag is ESP_INTR_FLAG_IRAM, please use the memory allocated from internal RAM.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • cmd_handle: I2C cmd link

  • data: pointer accept the data byte

Parameters
  • ack: ack value for read command

esp_err_t i2c_master_read(i2c_cmd_handle_t cmd_handle, uint8_t *data, size_t data_len, i2c_ack_type_t ack)

Queue command for I2C master to read data from I2C bus.

Note

Only call this function in I2C master mode Call i2c_master_cmd_begin() to send all queued commands

Note

If the psram is enabled and intr_flag is ESP_INTR_FLAG_IRAM, please use the memory allocated from internal RAM.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • cmd_handle: I2C cmd link

  • data: data buffer to accept the data from bus

Parameters
  • data_len: read data length

  • ack: ack value for read command

esp_err_t i2c_master_stop(i2c_cmd_handle_t cmd_handle)

Queue command for I2C master to generate a stop signal.

Note

Only call this function in I2C master mode Call i2c_master_cmd_begin() to send all queued commands

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • cmd_handle: I2C cmd link

esp_err_t i2c_master_cmd_begin(i2c_port_t i2c_num, i2c_cmd_handle_t cmd_handle, TickType_t ticks_to_wait)

I2C master send queued commands. This function will trigger sending all queued commands. The task will be blocked until all the commands have been sent out. The I2C APIs are not thread-safe, if you want to use one I2C port in different tasks, you need to take care of the multi-thread issue.

Note

Only call this function in I2C master mode

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_FAIL Sending command error, slave doesn’t ACK the transfer.

  • ESP_ERR_INVALID_STATE I2C driver not installed or not in master mode.

  • ESP_ERR_TIMEOUT Operation timeout because the bus is busy.

Parameters
  • i2c_num: I2C port number

  • cmd_handle: I2C command handler

  • ticks_to_wait: maximum wait ticks.

int i2c_slave_write_buffer(i2c_port_t i2c_num, const uint8_t *data, int size, TickType_t ticks_to_wait)

I2C slave write data to internal ringbuffer, when tx fifo empty, isr will fill the hardware fifo from the internal ringbuffer.

Note

Only call this function in I2C slave mode

Return

  • ESP_FAIL(-1) Parameter error

  • Others(>=0) The number of data bytes that pushed to the I2C slave buffer.

Parameters
  • i2c_num: I2C port number

  • data: data pointer to write into internal buffer

  • size: data size

  • ticks_to_wait: Maximum waiting ticks

int i2c_slave_read_buffer(i2c_port_t i2c_num, uint8_t *data, size_t max_size, TickType_t ticks_to_wait)

I2C slave read data from internal buffer. When I2C slave receive data, isr will copy received data from hardware rx fifo to internal ringbuffer. Then users can read from internal ringbuffer.

Note

Only call this function in I2C slave mode

Return

  • ESP_FAIL(-1) Parameter error

  • Others(>=0) The number of data bytes that read from I2C slave buffer.

Parameters
  • i2c_num: I2C port number

  • data: data pointer to accept data from internal buffer

  • max_size: Maximum data size to read

  • ticks_to_wait: Maximum waiting ticks

esp_err_t i2c_set_period(i2c_port_t i2c_num, int high_period, int low_period)

set I2C master clock period

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • high_period: clock cycle number during SCL is high level, high_period is a 14 bit value

  • low_period: clock cycle number during SCL is low level, low_period is a 14 bit value

esp_err_t i2c_get_period(i2c_port_t i2c_num, int *high_period, int *low_period)

get I2C master clock period

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • high_period: pointer to get clock cycle number during SCL is high level, will get a 14 bit value

  • low_period: pointer to get clock cycle number during SCL is low level, will get a 14 bit value

esp_err_t i2c_filter_enable(i2c_port_t i2c_num, uint8_t cyc_num)

enable hardware filter on I2C bus Sometimes the I2C bus is disturbed by high frequency noise(about 20ns), or the rising edge of the SCL clock is very slow, these may cause the master state machine broken. enable hardware filter can filter out high frequency interference and make the master more stable.

Note

Enable filter will slow the SCL clock.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • cyc_num: the APB cycles need to be filtered(0<= cyc_num <=7). When the period of a pulse is less than cyc_num * APB_cycle, the I2C controller will ignore this pulse.

esp_err_t i2c_filter_disable(i2c_port_t i2c_num)

disable filter on I2C bus

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

esp_err_t i2c_set_start_timing(i2c_port_t i2c_num, int setup_time, int hold_time)

set I2C master start signal timing

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • setup_time: clock number between the falling-edge of SDA and rising-edge of SCL for start mark, it’s a 10-bit value.

  • hold_time: clock num between the falling-edge of SDA and falling-edge of SCL for start mark, it’s a 10-bit value.

esp_err_t i2c_get_start_timing(i2c_port_t i2c_num, int *setup_time, int *hold_time)

get I2C master start signal timing

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • setup_time: pointer to get setup time

  • hold_time: pointer to get hold time

esp_err_t i2c_set_stop_timing(i2c_port_t i2c_num, int setup_time, int hold_time)

set I2C master stop signal timing

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • setup_time: clock num between the rising-edge of SCL and the rising-edge of SDA, it’s a 10-bit value.

  • hold_time: clock number after the STOP bit’s rising-edge, it’s a 14-bit value.

esp_err_t i2c_get_stop_timing(i2c_port_t i2c_num, int *setup_time, int *hold_time)

get I2C master stop signal timing

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • setup_time: pointer to get setup time.

  • hold_time: pointer to get hold time.

esp_err_t i2c_set_data_timing(i2c_port_t i2c_num, int sample_time, int hold_time)

set I2C data signal timing

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • sample_time: clock number I2C used to sample data on SDA after the rising-edge of SCL, it’s a 10-bit value

  • hold_time: clock number I2C used to hold the data after the falling-edge of SCL, it’s a 10-bit value

esp_err_t i2c_get_data_timing(i2c_port_t i2c_num, int *sample_time, int *hold_time)

get I2C data signal timing

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • sample_time: pointer to get sample time

  • hold_time: pointer to get hold time

esp_err_t i2c_set_timeout(i2c_port_t i2c_num, int timeout)

set I2C timeout value

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • timeout: timeout value for I2C bus (unit: APB 80Mhz clock cycle)

esp_err_t i2c_get_timeout(i2c_port_t i2c_num, int *timeout)

get I2C timeout value

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • timeout: pointer to get timeout value

esp_err_t i2c_set_data_mode(i2c_port_t i2c_num, i2c_trans_mode_t tx_trans_mode, i2c_trans_mode_t rx_trans_mode)

set I2C data transfer mode

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • tx_trans_mode: I2C sending data mode

  • rx_trans_mode: I2C receving data mode

esp_err_t i2c_get_data_mode(i2c_port_t i2c_num, i2c_trans_mode_t *tx_trans_mode, i2c_trans_mode_t *rx_trans_mode)

get I2C data transfer mode

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters
  • i2c_num: I2C port number

  • tx_trans_mode: pointer to get I2C sending data mode

  • rx_trans_mode: pointer to get I2C receiving data mode

Macros

I2C_APB_CLK_FREQ

I2C source clock is APB clock, 80MHz

I2C_NUM_0

I2C port 0

I2C_NUM_1

I2C port 1

I2C_NUM_MAX

I2C port max

Type Definitions

typedef void *i2c_cmd_handle_t

I2C command handle

Structures

struct i2c_config_t

I2C initialization parameters.

Public Members

i2c_mode_t mode

I2C mode

int sda_io_num

GPIO number for I2C sda signal

int scl_io_num

GPIO number for I2C scl signal

bool sda_pullup_en

Internal GPIO pull mode for I2C sda signal

bool scl_pullup_en

Internal GPIO pull mode for I2C scl signal

uint32_t clk_speed

I2C clock frequency for master mode, (no higher than 1MHz for now)

struct i2c_config_t::[anonymous]::[anonymous] master

I2C master config

uint8_t addr_10bit_en

I2C 10bit address mode enable for slave mode

uint16_t slave_addr

I2C address for slave mode

struct i2c_config_t::[anonymous]::[anonymous] slave

I2C slave config

uint32_t clk_flags

Bitwise of I2C_SCLK_SRC_FLAG_**FOR_DFS** for clk source choice

Macros

I2C_SCLK_SRC_FLAG_FOR_NOMAL

Any one clock source that is available for the specified frequency may be choosen

I2C_SCLK_SRC_FLAG_AWARE_DFS

For REF tick clock, it won’t change with APB.

I2C_SCLK_SRC_FLAG_LIGHT_SLEEP

For light sleep mode.

I2C_CLK_FREQ_MAX

Use the highest speed that is available for the clock source picked by clk_flags.

Type Definitions

typedef int i2c_port_t

I2C port number, can be I2C_NUM_0 ~ (I2C_NUM_MAX-1).

Enumerations

enum i2c_mode_t

Values:

I2C_MODE_SLAVE = 0

I2C slave mode

I2C_MODE_MASTER

I2C master mode

I2C_MODE_MAX
enum i2c_rw_t

Values:

I2C_MASTER_WRITE = 0

I2C write data

I2C_MASTER_READ

I2C read data

enum i2c_trans_mode_t

Values:

I2C_DATA_MODE_MSB_FIRST = 0

I2C data msb first

I2C_DATA_MODE_LSB_FIRST = 1

I2C data lsb first

I2C_DATA_MODE_MAX
enum i2c_addr_mode_t

Values:

I2C_ADDR_BIT_7 = 0

I2C 7bit address for slave mode

I2C_ADDR_BIT_10

I2C 10bit address for slave mode

I2C_ADDR_BIT_MAX
enum i2c_ack_type_t

Values:

I2C_MASTER_ACK = 0x0

I2C ack for each byte read

I2C_MASTER_NACK = 0x1

I2C nack for each byte read

I2C_MASTER_LAST_NACK = 0x2

I2C nack for the last byte

I2C_MASTER_ACK_MAX
enum i2c_sclk_t

I2C clock source, sorting from smallest to largest, place them in order. This can be expanded in the future use.

Values:

I2C_SCLK_DEFAULT = 0

I2C source clock not selected

I2C_SCLK_APB

I2C source clock from APB, 80M

I2C_SCLK_MAX
enum i2c_opmode_t

Values:

I2C_CMD_RESTART = 0

I2C restart command

I2C_CMD_WRITE

I2C write command

I2C_CMD_READ

I2C read command

I2C_CMD_STOP

I2C stop command

I2C_CMD_END

I2C end command