Get Started¶
This document is intended to help you set up the software development environment for the hardware based on the ESP32 chip by Espressif.
After that, a simple example will show you how to use ESP-IDF (Espressif IoT Development Framework) for menu configuration, then building, and flashing firmware onto an ESP32 board.
Note
This is documentation for stable version v4.0.4 of ESP-IDF. Other ESP-IDF Versions are also available.
Introduction¶
ESP32 is a system on a chip that integrates the following features:
Wi-Fi (2.4 GHz band)
Bluetooth 4.2
Dual high performance cores
Ultra Low Power co-processor
Several peripherals
Powered by 40 nm technology, ESP32 provides a robust, highly integrated platform, which helps meet the continuous demands for efficient power usage, compact design, security, high performance, and reliability.
Espressif provides basic hardware and software resources to help application developers realize their ideas using the ESP32 series hardware. The software development framework by Espressif is intended for development of Internet-of-Things (IoT) applications with Wi-Fi, Bluetooth, power management and several other system features.
What You Need¶
Hardware:
An ESP32 board
USB cable - USB A / micro USB B
Computer running Windows, Linux, or macOS
Software:
Toolchain to compile code for ESP32
Build tools - CMake and Ninja to build a full Application for ESP32
ESP-IDF that essentially contains API (software libraries and source code) for ESP32 and scripts to operate the Toolchain
Text editor to write programs (Projects) in C, e.g., Eclipse
Development Board Overviews¶
If you have one of ESP32 development boards listed below, you can click on the link to learn more about its hardware.
Installation Step by Step¶
This is a detailed roadmap to walk you through the installation process.
Setting up Development Environment¶
Step 1. Install prerequisites¶
Some tools need to be installed on the computer before proceeding to the next steps. Follow the links below for the instructions for your OS:
Step 2. Get ESP-IDF¶
To build applications for the ESP32, you need the software libraries provided by Espressif in ESP-IDF repository.
To get ESP-IDF, navigate to your installation directory and clone the repository with git clone
, following instructions below specific to your operating system.
Note
This guide uses the directory ~/esp
on Linux and macOS or %userprofile%\esp
on Windows as an installation folder for ESP-IDF. You can use any directory, but you will need to adjust paths for the commands respectively. Keep in mind that ESP-IDF does not support spaces in paths.
Linux and macOS¶
Open Terminal, and run the following commands:
cd ~/esp
git clone -b v4.0.4 --recursive https://github.com/espressif/esp-idf.git
ESP-IDF will be downloaded into ~/esp/esp-idf
.
Consult ESP-IDF Versions for information about which ESP-IDF version to use in a given situation.
Windows¶
In addition to installing the tools, ESP-IDF Tools Installer for Windows introduced in Step 1 can also download a copy of ESP-IDF.
Consult ESP-IDF Versions for information about which ESP-IDF version to use in a given situation.
If you wish to download ESP-IDF without the help of ESP-IDF Tools Installer, refer to these instructions.
Step 3. Set up the tools¶
Aside from the ESP-IDF, you also need to install the tools used by ESP-IDF, such as the compiler, debugger, Python packages, etc.
Windows¶
ESP-IDF Tools Installer for Windows introduced in Step 1 installs all the required tools.
If you want to install the tools without the help of ESP-IDF Tools Installer, open the Command Prompt and follow these steps:
cd %userprofile%\esp\esp-idf
install.bat
Linux and macOS¶
cd ~/esp/esp-idf
./install.sh
Alternative File Downloads¶
The tools installer downloads a number of files attached to GitHub Releases. If accessing GitHub is slow then it is possible to set an environment variable to prefer Espressif’s download server for GitHub asset downloads.
Note
This setting only controls individual tools downloaded from GitHub releases, it doesn’t change the URLs used to access any Git repositories.
Windows¶
To prefer the Espressif download server when running the ESP-IDF Tools Installer or installing tools from the command line, open the System control panel, then click on Advanced Settings. Add a new Environment Variable (of type either User or System) with the name IDF_GITHUB_ASSETS
and value dl.espressif.com/github_assets
. Click OK once done.
If the command line window or ESP-IDF Tools Installer window was already open before you added the new environment variable, you will need to close and reopen it.
While this environment variable is still set, the ESP-IDF Tools Installer and the command line installer will prefer the Espressif download server.
Linux and macOS¶
To prefer the Espressif download server when installing tools, use the following sequence of commands when running install.sh
:
cd ~/esp/esp-idf
export IDF_GITHUB_ASSETS="dl.espressif.com/github_assets"
./install.sh
Customizing the tools installation path¶
The scripts introduced in this step install compilation tools required by ESP-IDF inside the user home directory: $HOME/.espressif
on Linux and macOS, %USERPROFILE%\.espressif
on Windows. If you wish to install the tools into a different directory, set the environment variable IDF_TOOLS_PATH
before running the installation scripts. Make sure that your user has sufficient permissions to read and write this path.
If changing the IDF_TOOLS_PATH
, make sure it is set to the same value every time the install.bat
/install.sh
and export.bat
/export.sh
scripts are executed.
Step 4. Set up the environment variables¶
The installed tools are not yet added to the PATH environment variable. To make the tools usable from the command line, some environment variables must be set. ESP-IDF provides another script which does that.
Windows¶
ESP-IDF Tools Installer for Windows creates an “ESP-IDF Command Prompt” shortcut in the Start Menu. This shortcut opens the Command Prompt and sets up all the required environment variables. You can open this shortcut and proceed to the next step.
Alternatively, if you want to use ESP-IDF in an existing Command Prompt window, you can run:
%userprofile%\esp\esp-idf\export.bat
Linux and macOS¶
In the terminal where you are going to use ESP-IDF, run:
. $HOME/esp/esp-idf/export.sh
Note the space between the leading dot and the path!
If you plan to use esp-idf frequently, you can create an alias for executing export.sh
:
Copy and paste the following command to your shell’s profile (
.profile
,.bashrc
,.zprofile
, etc.)alias get_idf='. $HOME/esp/esp-idf/export.sh'
Refresh the configuration by restarting the terminal session or by running
source [path to profile]
, for example,source ~/.bashrc
.
Now you can run get_idf
to set up or refresh the esp-idf environment in any terminal session.
Technically, you can add export.sh
to your shell’s profile directly; however, it is not recommended. Doing so activates IDF virtual environment in every terminal session (including those where IDF is not needed), defeating the purpose of the virtual environment and likely affecting other software.
Step 5. Start a Project¶
Now you are ready to prepare your application for ESP32. You can start with get-started/hello_world project from examples directory in IDF.
Copy get-started/hello_world to ~/esp
directory:
Linux and macOS¶
cd ~/esp
cp -r $IDF_PATH/examples/get-started/hello_world .
Windows¶
cd %userprofile%\esp
xcopy /e /i %IDF_PATH%\examples\get-started\hello_world hello_world
There is a range of example projects in the examples directory in ESP-IDF. You can copy any project in the same way as presented above and run it.
It is also possible to build examples in-place, without copying them first.
Important
The ESP-IDF build system does not support spaces in the paths to either ESP-IDF or to projects.
Step 6. Connect Your Device¶
Now connect your ESP32 board to the computer and check under what serial port the board is visible.
Serial ports have the following patterns in their names:
Windows: names like
COM1
Linux: starting with
/dev/tty
macOS: starting with
/dev/cu.
If you are not sure how to check the serial port name, please refer to Establish Serial Connection with ESP32 for full details.
Note
Keep the port name handy as you will need it in the next steps.
Step 7. Configure¶
Navigate to your hello_world
directory from Step 5. Start a Project and run the project configuration utility menuconfig
.
Linux and macOS¶
cd ~/esp/hello_world
idf.py menuconfig
Windows¶
cd %userprofile%\esp\hello_world
idf.py menuconfig
If the previous steps have been done correctly, the following menu appears:
To navigate and use menuconfig
, press the following keys:
Arrow keys for navigation
Enter
to go into a submenuEsc
to go up one level or exit?
to see a help screen for menu or configuration item. Enter key exits the help screenSpace
, orY
andN
keys to enable (Yes) and disable (No) configuration items with checkboxes “[*]
”/
to find configuration items
Attention
If you use ESP32-DevKitC board with the ESP32-SOLO-1 module, enable single core mode (CONFIG_FREERTOS_UNICORE) in menuconfig before flashing examples.
Step 8. Build the Project¶
Build the project by running:
idf.py build
This command will compile the application and all ESP-IDF components, then it will generate the bootloader, partition table, and application binaries.
$ idf.py build
Running cmake in directory /path/to/hello_world/build
Executing "cmake -G Ninja --warn-uninitialized /path/to/hello_world"...
Warn about uninitialized values.
-- Found Git: /usr/bin/git (found version "2.17.0")
-- Building empty aws_iot component due to configuration
-- Component names: ...
-- Component paths: ...
... (more lines of build system output)
[527/527] Generating hello-world.bin
esptool.py v2.3.1
Project build complete. To flash, run this command:
../../../components/esptool_py/esptool/esptool.py -p (PORT) -b 921600 write_flash --flash_mode dio --flash_size detect --flash_freq 40m 0x10000 build/hello-world.bin build 0x1000 build/bootloader/bootloader.bin 0x8000 build/partition_table/partition-table.bin
or run 'idf.py -p PORT flash'
If there are no errors, the build will finish by generating the firmware binary .bin file.
Step 9. Flash onto the Device¶
Flash the binaries that you just built onto your ESP32 board by running:
idf.py -p PORT [-b BAUD] flash
Replace PORT with your ESP32 board’s serial port name from Step 6. Connect Your Device.
You can also change the flasher baud rate by replacing BAUD with the baud rate you need. The default baud rate is 460800
.
For more information on idf.py arguments, see idf.py.
Note
The option flash
automatically builds and flashes the project, so running idf.py build
is not necessary.
Running esptool.py in directory [...]/esp/hello_world
Executing "python [...]/esp-idf/components/esptool_py/esptool/esptool.py -b 460800 write_flash @flash_project_args"...
esptool.py -b 460800 write_flash --flash_mode dio --flash_size detect --flash_freq 40m 0x1000 bootloader/bootloader.bin 0x8000 partition_table/partition-table.bin 0x10000 hello-world.bin
esptool.py v2.3.1
Connecting....
Detecting chip type... ESP32
Chip is ESP32D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 460800
Changed.
Configuring flash size...
Auto-detected Flash size: 4MB
Flash params set to 0x0220
Compressed 22992 bytes to 13019...
Wrote 22992 bytes (13019 compressed) at 0x00001000 in 0.3 seconds (effective 558.9 kbit/s)...
Hash of data verified.
Compressed 3072 bytes to 82...
Wrote 3072 bytes (82 compressed) at 0x00008000 in 0.0 seconds (effective 5789.3 kbit/s)...
Hash of data verified.
Compressed 136672 bytes to 67544...
Wrote 136672 bytes (67544 compressed) at 0x00010000 in 1.9 seconds (effective 567.5 kbit/s)...
Hash of data verified.
Leaving...
Hard resetting via RTS pin...
If there are no issues by the end of the flash process, the module will be reset and the “hello_world” application will be running.
Step 10. Monitor¶
To check if “hello_world” is indeed running, type idf.py -p PORT monitor
(Do not forget to replace PORT with your serial port name).
This command launches the IDF Monitor application:
$ idf.py -p /dev/ttyUSB0 monitor
Running idf_monitor in directory [...]/esp/hello_world/build
Executing "python [...]/esp-idf/tools/idf_monitor.py -b 115200 [...]/esp/hello_world/build/hello-world.elf"...
--- idf_monitor on /dev/ttyUSB0 115200 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
ets Jun 8 2016 00:22:57
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
ets Jun 8 2016 00:22:57
...
After startup and diagnostic logs scroll up, you should see “Hello world!” printed out by the application.
...
Hello world!
Restarting in 10 seconds...
I (211) cpu_start: Starting scheduler on APP CPU.
Restarting in 9 seconds...
Restarting in 8 seconds...
Restarting in 7 seconds...
To exit IDF monitor use the shortcut Ctrl+]
.
If IDF monitor fails shortly after the upload, or, if instead of the messages above, you see random garbage similar to what is given below, your board is likely using a 26MHz crystal. Most development board designs use 40MHz, so ESP-IDF uses this frequency as a default value.
If you have such a problem, do the following:
Exit the monitor.
Go back to menuconfig.
Go to Component config –> ESP32-specific –> Main XTAL frequency, then change CONFIG_ESP32_XTAL_FREQ_SEL to 26MHz.
After that, build and flash the application again.
Note
You can combine building, flashing and monitoring into one step by running:
idf.py -p PORT flash monitor
See also:
IDF Monitor for handy shortcuts and more details on using IDF monitor.
idf.py for a full reference of
idf.py
commands and options.
That’s all that you need to get started with ESP32!
Now you are ready to try some other examples, or go straight to developing your own applications.
Updating ESP-IDF¶
You should update ESP-IDF from time to time, as newer versions fix bugs and provide new features. The simplest way to do the update is to delete the existing esp-idf
folder and clone it again, as if performing the initial installation described in Step 2. Get ESP-IDF.
Another solution is to update only what has changed. The update procedure depends on the version of ESP-IDF you are using.
After updating ESP-IDF, execute install.sh
(install.bat
on Windows) again, in case the new ESP-IDF version requires different versions of tools. See instructions at Step 3. Set up the tools.
Once the new tools are installed, update the environment using export.sh
(export.bat
on Windows). See instructions at Step 4. Set up the environment variables.