SPI Slave Driver

[中文]

SPI Slave driver is a program that controls ESP32-C3's General Purpose SPI (GP-SPI) peripheral(s) when it functions as a slave.

For more hardware information about the GP-SPI peripheral(s), see ESP32-C3 Technical Reference Manual > SPI Controller [PDF].

Terminology

The terms used in relation to the SPI slave driver are given in the table below.

Term

Definition

Host

The SPI controller peripheral external to ESP32-C3 that initiates SPI transmissions over the bus, and acts as an SPI Master.

Device

SPI slave device (general purpose SPI controller). Each Device shares the MOSI, MISO and SCLK signals but is only active on the bus when the Host asserts the Device's individual CS line.

Bus

A signal bus, common to all Devices connected to one Host. In general, a bus includes the following lines: MISO, MOSI, SCLK, one or more CS lines, and, optionally, QUADWP and QUADHD. So Devices are connected to the same lines, with the exception that each Device has its own CS line. Several Devices can also share one CS line if connected in the daisy-chain manner.

MISO

Master In, Slave Out, a.k.a. Q. Data transmission from a Device to Host.

MOSI

Master Out, Slave In, a.k.a. D. Data transmission from a Host to Device.

SCLK

Serial Clock. Oscillating signal generated by a Host that keeps the transmission of data bits in sync.

CS

Chip Select. Allows a Host to select individual Device(s) connected to the bus in order to send or receive data.

QUADWP

Write Protect signal. Only used for 4-bit (qio/qout) transactions.

QUADHD

Hold signal. Only used for 4-bit (qio/qout) transactions.

Assertion

The action of activating a line. The opposite action of returning the line back to inactive (back to idle) is called de-assertion.

Transaction

One instance of a Host asserting a CS line, transferring data to and from a Device, and de-asserting the CS line. Transactions are atomic, which means they can never be interrupted by another transaction.

Launch Edge

Edge of the clock at which the source register launches the signal onto the line.

Latch Edge

Edge of the clock at which the destination register latches in the signal.

Driver Features

The SPI slave driver allows using the SPI peripherals as full-duplex Devices. The driver can send/receive transactions up to 64 bytes in length, or utilize DMA to send/receive longer transactions. However, there are some known issues related to DMA.

The SPI slave driver supports registering the SPI ISR to a certain CPU core. If multiple tasks try to access the same SPI Device simultaneously, it is recommended that your application be refactored so that each SPI peripheral is only accessed by a single task at a time. Please also use spi_bus_config_t::isr_cpu_id to register the SPI ISR to the same core as SPI peripheral related tasks to ensure thread safety.

SPI Transactions

A full-duplex SPI transaction begins when the Host asserts the CS line and starts sending out clock pulses on the SCLK line. Every clock pulse, a data bit is shifted from the Host to the Device on the MOSI line and back on the MISO line at the same time. At the end of the transaction, the Host de-asserts the CS line.

The attributes of a transaction are determined by the configuration structure for an SPI peripheral acting as a slave device spi_slave_interface_config_t, and transaction configuration structure spi_slave_transaction_t.

As not every transaction requires both writing and reading data, you can choose to configure the spi_transaction_t structure for TX only, RX only, or TX and RX transactions. If spi_slave_transaction_t::rx_buffer is set to NULL, the read phase will be skipped. Similarly, if spi_slave_transaction_t::tx_buffer is set to NULL, the write phase will be skipped.

Note

A Host should not start a transaction before its Device is ready for receiving data. It is recommended to use another GPIO pin for a handshake signal to sync the Devices. For more details, see Transaction Interval.

Driver Usage

  • Initialize an SPI peripheral as a Device by calling the function spi_slave_initialize(). Make sure to set the correct I/O pins in the struct bus_config. Set the unused signals to -1.

  • Before initiating transactions, fill one or more spi_slave_transaction_t structs with the transaction parameters required. Either queue all transactions by calling the function spi_slave_queue_trans() and, at a later time, query the result by using the function spi_slave_get_trans_result(), or handle all requests individually by feeding them into spi_slave_transmit(). The latter two functions will be blocked until the Host has initiated and finished a transaction, causing the queued data to be sent and received.

  • (Optional) To unload the SPI slave driver, call spi_slave_free().

Transaction Data and Master/Slave Length Mismatches

Normally, the data that needs to be transferred to or from a Device is read or written to a chunk of memory indicated by the spi_slave_transaction_t::rx_buffer and spi_slave_transaction_t::tx_buffer. The SPI driver can be configured to use DMA for transfers, in which case these buffers must be allocated in DMA-capable memory using pvPortMallocCaps(size, MALLOC_CAP_DMA).

The amount of data that the driver can read or write to the buffers is limited by spi_slave_transaction_t::length. However, this member does not define the actual length of an SPI transaction. A transaction's length is determined by the clock and CS lines driven by the Host. The actual length of the transmission can be read only after a transaction is finished from the member spi_slave_transaction_t::trans_len.

If the length of the transmission is greater than the buffer length, only the initial number of bits specified in the spi_slave_transaction_t::length member will be sent and received. In this case, spi_slave_transaction_t::trans_len is set to spi_slave_transaction_t::length instead of the actual transaction length. To meet the actual transaction length requirements, set spi_slave_transaction_t::length to a value greater than the maximum spi_slave_transaction_t::trans_len expected. If the transmission length is shorter than the buffer length, only the data equal to the length of the buffer will be transmitted.

GPIO Matrix and IO_MUX

Most of chip's peripheral signals have direct connection to their dedicated IO_MUX pins. However, the signals can also be routed to any other available pins using the less direct GPIO matrix. If at least one signal is routed through the GPIO matrix, then all signals will be routed through it.

When an SPI Host is set to 80 MHz or lower frequencies, routing SPI pins via GPIO matrix will behave the same compared to routing them via IO_MUX.

The IO_MUX pins for SPI buses are given below.

Pin Name

GPIO Number (SPI2)

CS0

10

SCLK

6

MISO

2

MOSI

7

QUADWP

5

QUADHD

4

Speed and Timing Considerations

Transaction Interval

The ESP32-C3 SPI slave peripherals are designed as general purpose Devices controlled by a CPU. As opposed to dedicated slaves, CPU-based SPI Devices have a limited number of pre-defined registers. All transactions must be handled by the CPU, which means that the transfers and responses are not real-time, and there might be noticeable latency.

As a solution, a Device's response rate can be doubled by using the functions spi_slave_queue_trans() and then spi_slave_get_trans_result() instead of using spi_slave_transmit().

You can also configure a GPIO pin through which the Device will signal to the Host when it is ready for a new transaction. A code example of this can be found in peripherals/spi_slave.

SCLK Frequency Requirements

The SPI slaves are designed to operate at up to 60 MHz. The data cannot be recognized or received correctly if the clock is too fast or does not have a 50% duty cycle.

Restrictions and Known Issues

  1. If DMA is enabled, the rx buffer should be word-aligned (starting from a 32-bit boundary and having a length of multiples of 4 bytes). Otherwise, DMA may write incorrectly or not in a boundary aligned manner. The driver reports an error if this condition is not satisfied.

    Also, a Host should write lengths that are multiples of 4 bytes. The data with inappropriate lengths will be discarded.

Application Example

The code example for Device/Host communication can be found in the peripherals/spi_slave directory of ESP-IDF examples.

API Reference

Header File

  • components/driver/spi/include/driver/spi_slave.h

  • This header file can be included with:

    #include "driver/spi_slave.h"

  • This header file is a part of the API provided by the driver component. To declare that your component depends on driver, add the following to your CMakeLists.txt:

    REQUIRES driver

    or

    PRIV_REQUIRES driver

Functions

esp_err_t spi_slave_initialize(spi_host_device_t host, const spi_bus_config_t *bus_config, const spi_slave_interface_config_t *slave_config, spi_dma_chan_t dma_chan)

Initialize a SPI bus as a slave interface.

Warning

SPI0/1 is not supported

Warning

If a DMA channel is selected, any transmit and receive buffer used should be allocated in DMA-capable memory.

Warning

The ISR of SPI is always executed on the core which calls this function. Never starve the ISR on this core or the SPI transactions will not be handled.

Parameters

  • host -- SPI peripheral to use as a SPI slave interface

  • bus_config -- Pointer to a spi_bus_config_t struct specifying how the host should be initialized

  • slave_config -- Pointer to a spi_slave_interface_config_t struct specifying the details for the slave interface

  • dma_chan -- - Selecting a DMA channel for an SPI bus allows transactions on the bus with size only limited by the amount of internal memory.

    • Selecting SPI_DMA_DISABLED limits the size of transactions.

    • Set to SPI_DMA_DISABLED if only the SPI flash uses this bus.

    • Set to SPI_DMA_CH_AUTO to let the driver to allocate the DMA channel.

Returns

  • ESP_ERR_INVALID_ARG if configuration is invalid

  • ESP_ERR_INVALID_STATE if host already is in use

  • ESP_ERR_NOT_FOUND if there is no available DMA channel

  • ESP_ERR_NO_MEM if out of memory

  • ESP_OK on success

esp_err_t spi_slave_free(spi_host_device_t host)

Free a SPI bus claimed as a SPI slave interface.

Parameters

host -- SPI peripheral to free

Returns

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_INVALID_STATE if not all devices on the bus are freed

  • ESP_OK on success

esp_err_t spi_slave_queue_trans(spi_host_device_t host, const spi_slave_transaction_t *trans_desc, TickType_t ticks_to_wait)

Queue a SPI transaction for execution.

Queues a SPI transaction to be executed by this slave device. (The transaction queue size was specified when the slave device was initialised via spi_slave_initialize.) This function may block if the queue is full (depending on the ticks_to_wait parameter). No SPI operation is directly initiated by this function, the next queued transaction will happen when the master initiates a SPI transaction by pulling down CS and sending out clock signals.

This function hands over ownership of the buffers in trans_desc to the SPI slave driver; the application is not to access this memory until spi_slave_queue_trans is called to hand ownership back to the application.

Parameters

  • host -- SPI peripheral that is acting as a slave

  • trans_desc -- Description of transaction to execute. Not const because we may want to write status back into the transaction description.

  • ticks_to_wait -- Ticks to wait until there's room in the queue; use portMAX_DELAY to never time out.

Returns

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_OK on success

esp_err_t spi_slave_get_trans_result(spi_host_device_t host, spi_slave_transaction_t **trans_desc, TickType_t ticks_to_wait)

Get the result of a SPI transaction queued earlier.

This routine will wait until a transaction to the given device (queued earlier with spi_slave_queue_trans) has succesfully completed. It will then return the description of the completed transaction so software can inspect the result and e.g. free the memory or re-use the buffers.

It is mandatory to eventually use this function for any transaction queued by spi_slave_queue_trans.

Parameters

  • host -- SPI peripheral to that is acting as a slave

  • trans_desc -- [out] Pointer to variable able to contain a pointer to the description of the transaction that is executed

  • ticks_to_wait -- Ticks to wait until there's a returned item; use portMAX_DELAY to never time out.

Returns

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_NOT_SUPPORTED if flag SPI_SLAVE_NO_RETURN_RESULT is set

  • ESP_OK on success

esp_err_t spi_slave_transmit(spi_host_device_t host, spi_slave_transaction_t *trans_desc, TickType_t ticks_to_wait)

Do a SPI transaction.

Essentially does the same as spi_slave_queue_trans followed by spi_slave_get_trans_result. Do not use this when there is still a transaction queued that hasn't been finalized using spi_slave_get_trans_result.

Parameters

  • host -- SPI peripheral to that is acting as a slave

  • trans_desc -- Pointer to variable able to contain a pointer to the description of the transaction that is executed. Not const because we may want to write status back into the transaction description.

  • ticks_to_wait -- Ticks to wait until there's a returned item; use portMAX_DELAY to never time out.

Returns

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_OK on success

Structures

struct spi_slave_interface_config_t

This is a configuration for a SPI host acting as a slave device.

Public Members

int spics_io_num

CS GPIO pin for this device.

uint32_t flags

Bitwise OR of SPI_SLAVE_* flags.

int queue_size

Transaction queue size. This sets how many transactions can be 'in the air' (queued using spi_slave_queue_trans but not yet finished using spi_slave_get_trans_result) at the same time.

uint8_t mode

SPI mode, representing a pair of (CPOL, CPHA) configuration:

  • 0: (0, 0)

  • 1: (0, 1)

  • 2: (1, 0)

  • 3: (1, 1)

slave_transaction_cb_t post_setup_cb

Callback called after the SPI registers are loaded with new data.

This callback is called within interrupt context should be in IRAM for best performance, see "Transferring Speed" section in the SPI Master documentation for full details. If not, the callback may crash during flash operation when the driver is initialized with ESP_INTR_FLAG_IRAM.

slave_transaction_cb_t post_trans_cb

Callback called after a transaction is done.

This callback is called within interrupt context should be in IRAM for best performance, see "Transferring Speed" section in the SPI Master documentation for full details. If not, the callback may crash during flash operation when the driver is initialized with ESP_INTR_FLAG_IRAM.

struct spi_slave_transaction_t

This structure describes one SPI transaction

Public Members

size_t length

Total data length, in bits.

size_t trans_len

Transaction data length, in bits.

const void *tx_buffer

Pointer to transmit buffer, or NULL for no MOSI phase.

void *rx_buffer

Pointer to receive buffer, or NULL for no MISO phase. When the DMA is anabled, must start at WORD boundary (rx_buffer%4==0), and has length of a multiple of 4 bytes.

void *user

User-defined variable. Can be used to store eg transaction ID.

Macros

SPI_SLAVE_TXBIT_LSBFIRST

Transmit command/address/data LSB first instead of the default MSB first.

SPI_SLAVE_RXBIT_LSBFIRST

Receive data LSB first instead of the default MSB first.

SPI_SLAVE_BIT_LSBFIRST

Transmit and receive LSB first.

SPI_SLAVE_NO_RETURN_RESULT

Don't return the descriptor to the host on completion (use post_trans_cb to notify instead)

Type Definitions

typedef void (*slave_transaction_cb_t)(spi_slave_transaction_t *trans)

Provide feedback about this document