Universal Asynchronous Receiver/Transmitter (UART)

Overview

A Universal Asynchronous Receiver/Transmitter (UART) is a hardware feature that handles communication (i.e., timing requirements and data framing) using widely-adopted asynchronous serial communication interfaces, such as RS232, RS422, RS485. A UART provides a widely adopted and cheap method to realize full-duplex or half-duplex data exchange among different devices.

The ESP32-S2 chip has two UART controllers (UART0 and UART1), each featuring an identical set of registers to simplify programming and for more flexibility.

Each UART controller is independently configurable with parameters such as baud rate, data bit length, bit ordering, number of stop bits, parity bit etc. All the controllers are compatible with UART-enabled devices from various manufacturers and can also support Infrared Data Association protocols (IrDA).

Functional Overview

The following overview describes how to establish communication between an ESP32-S2 and other UART devices using the functions and data types of the UART driver. The overview reflects a typical programming workflow and is broken down into the sections provided below:

  1. Setting Communication Parameters - Setting baud rate, data bits, stop bits, etc.

  2. Setting Communication Pins - Assigning pins for connection to a device.

  3. Driver Installation - Allocating ESP32-S2’s resources for the UART driver.

  4. Running UART Communication - Sending / receiving data

  5. Using Interrupts - Triggering interrupts on specific communication events

  6. Deleting a Driver - Freeing allocated resources if a UART communication is no longer required

Steps 1 to 3 comprise the configuration stage. Step 4 is where the UART starts operating. Steps 5 and 6 are optional.

The UART driver’s functions identify each of the UART controllers using uart_port_t. This identification is needed for all the following function calls.

Setting Communication Parameters

UART communication parameters can be configured all in a single step or individually in multiple steps.

Single Step

Call the function uart_param_config() and pass to it a uart_config_t structure. The uart_config_t structure should contain all the required parameters. See the example below.

const uart_port_t uart_num = UART_NUM_1;
uart_config_t uart_config = {
    .baud_rate = 115200,
    .data_bits = UART_DATA_8_BITS,
    .parity = UART_PARITY_DISABLE,
    .stop_bits = UART_STOP_BITS_1,
    .flow_ctrl = UART_HW_FLOWCTRL_CTS_RTS,
    .rx_flow_ctrl_thresh = 122,
};
// Configure UART parameters
ESP_ERROR_CHECK(uart_param_config(uart_num, &uart_config));

Multiple Steps

Configure specific parameters individually by calling a dedicated function from the table given below. These functions are also useful if re-configuring a single parameter.

Functions for Configuring specific parameters individually

Parameter to Configure

Function

Baud rate

uart_set_baudrate()

Number of transmitted bits

uart_set_word_length() selected out of uart_word_length_t

Parity control

uart_set_parity() selected out of uart_parity_t

Number of stop bits

uart_set_stop_bits() selected out of uart_stop_bits_t

Hardware flow control mode

uart_set_hw_flow_ctrl() selected out of uart_hw_flowcontrol_t

Communication mode

uart_set_mode() selected out of uart_mode_t

Each of the above functions has a _get_ counterpart to check the currently set value. For example, to check the current baud rate value, call uart_get_baudrate().

Setting Communication Pins

After setting communication parameters, configure the physical GPIO pins to which the other UART device will be connected. For this, call the function uart_set_pin() and specify the GPIO pin numbers to which the driver should route the Tx, Rx, RTS, and CTS signals. If you want to keep a currently allocated pin number for a specific signal, pass the macro UART_PIN_NO_CHANGE.

The same macro should be specified for pins that will not be used.

// Set UART pins(TX: IO4, RX: IO5, RTS: IO18, CTS: IO19)
ESP_ERROR_CHECK(uart_set_pin(UART_NUM_1, 4, 5, 18, 19));

Driver Installation

Once the communication pins are set, install the driver by calling uart_driver_install() and specify the following parameters:

  • Size of Tx ring buffer

  • Size of Rx ring buffer

  • Event queue handle and size

  • Flags to allocate an interrupt

The function will allocate the required internal resources for the UART driver.

// Setup UART buffered IO with event queue
const int uart_buffer_size = (1024 * 2);
QueueHandle_t uart_queue;
// Install UART driver using an event queue here
ESP_ERROR_CHECK(uart_driver_install(UART_NUM_1, uart_buffer_size, \
                                        uart_buffer_size, 10, &uart_queue, 0));

Once this step is complete, you can connect the external UART device and check the communication.

Running UART Communication

Serial communication is controlled by each UART controller’s finite state machine (FSM).

The process of sending data involves the following steps:

  1. Write data into Tx FIFO buffer

  2. FSM serializes the data

  3. FSM sends the data out

The process of receiving data is similar, but the steps are reversed:

  1. FSM processes an incoming serial stream and parallelizes it

  2. FSM writes the data into Rx FIFO buffer

  3. Read the data from Rx FIFO buffer

Therefore, an application will be limited to writing and reading data from a respective buffer using uart_write_bytes() and uart_read_bytes() respectively, and the FSM will do the rest.

Transmitting

After preparing the data for transmission, call the function uart_write_bytes() and pass the data buffer’s address and data length to it. The function will copy the data to the Tx ring buffer (either immediately or after enough space is available), and then exit. When there is free space in the Tx FIFO buffer, an interrupt service routine (ISR) moves the data from the Tx ring buffer to the Tx FIFO buffer in the background. The code below demonstrates the use of this function.

// Write data to UART.
char* test_str = "This is a test string.\n";
uart_write_bytes(uart_num, (const char*)test_str, strlen(test_str));

The function uart_write_bytes_with_break() is similar to uart_write_bytes() but adds a serial break signal at the end of the transmission. A ‘serial break signal’ means holding the Tx line low for a period longer than one data frame.

// Write data to UART, end with a break signal.
uart_write_bytes_with_break(uart_num, "test break\n",strlen("test break\n"), 100);

Another function for writing data to the Tx FIFO buffer is uart_tx_chars(). Unlike uart_write_bytes(), this function will not block until space is available. Instead, it will write all data which can immediately fit into the hardware Tx FIFO, and then return the number of bytes that were written.

There is a ‘companion’ function uart_wait_tx_done() that monitors the status of the Tx FIFO buffer and returns once it is empty.

// Wait for packet to be sent
const uart_port_t uart_num = UART_NUM_1;
ESP_ERROR_CHECK(uart_wait_tx_done(uart_num, 100)); // wait timeout is 100 RTOS ticks (TickType_t)

Receiving

Once the data is received by the UART and saved in the Rx FIFO buffer, it needs to be retrieved using the function uart_read_bytes(). Before reading data, you can check the number of bytes available in the Rx FIFO buffer by calling uart_get_buffered_data_len(). An example of using these functions is given below.

// Read data from UART.
const uart_port_t uart_num = UART_NUM_1;
uint8_t data[128];
int length = 0;
ESP_ERROR_CHECK(uart_get_buffered_data_len(uart_num, (size_t*)&length));
length = uart_read_bytes(uart_num, data, length, 100);

If the data in the Rx FIFO buffer is no longer needed, you can clear the buffer by calling uart_flush().

Software Flow Control

If the hardware flow control is disabled, you can manually set the RTS and DTR signal levels by using the functions uart_set_rts() and uart_set_dtr() respectively.

Communication Mode Selection

The UART controller supports a number of communication modes. A mode can be selected using the function uart_set_mode(). Once a specific mode is selected, the UART driver will handle the behavior of a connected UART device accordingly. As an example, it can control the RS485 driver chip using the RTS line to allow half-duplex RS485 communication.

// Setup UART in rs485 half duplex mode
ESP_ERROR_CHECK(uart_set_mode(uart_num, UART_MODE_RS485_HALF_DUPLEX));

Using Interrupts

There are many interrupts that can be generated following specific UART states or detected errors. The full list of available interrupts is provided in ESP32-S2 Technical Reference Manual > UART Controller (UART) > UART Interrupts and UHCI Interrupts [PDF]. You can enable or disable specific interrupts by calling uart_enable_intr_mask() or uart_disable_intr_mask() respectively. The mask of all interrupts is available as UART_INTR_MASK.

By default, the uart_driver_install() function installs the driver’s internal interrupt handler to manage the Tx and Rx ring buffers and provides high-level API functions like events (see below). It is also possible to register a lower level interrupt handler instead using uart_isr_register(), and to free it again using uart_isr_free(). Some UART driver functions which use the Tx and Rx ring buffers, events, etc. will not automatically work in this case - it is necessary to handle the interrupts directly in the ISR. Inside the custom handler implementation, clear the interrupt status bits using uart_clear_intr_status().

The API provides a convenient way to handle specific interrupts discussed in this document by wrapping them into dedicated functions:

  • Event detection: There are several events defined in uart_event_type_t that may be reported to a user application using the FreeRTOS queue functionality. You can enable this functionality when calling uart_driver_install() described in Driver Installation. An example of using Event detection can be found in peripherals/uart/uart_events.

  • FIFO space threshold or transmission timeout reached: The Tx and Rx FIFO buffers can trigger an interrupt when they are filled with a specific number of characters, or on a timeout of sending or receiving data. To use these interrupts, do the following:

  • Pattern detection: An interrupt triggered on detecting a ‘pattern’ of the same character being received/sent repeatedly for a number of times. This functionality is demonstrated in the example peripherals/uart/uart_events. It can be used, e.g., to detect a command string followed by a specific number of identical characters (the ‘pattern’) added at the end of the command string. The following functions are available:

Macros

The API also defines several macros. For example, UART_FIFO_LEN defines the length of hardware FIFO buffers; UART_BITRATE_MAX gives the maximum baud rate supported by the UART controllers, etc.

Deleting a Driver

If the communication established with uart_driver_install() is no longer required, the driver can be removed to free allocated resources by calling uart_driver_delete().

Overview of RS485 specific communication options

注解

The following section will use [UART_REGISTER_NAME].[UART_FIELD_BIT] to refer to UART register fields/bits. For more information on a specific option bit, see ESP32-S2 Technical Reference Manual > UART Controller (UART) > Register Summary [PDF]. Use the register name to navigate to the register description and then find the field/bit.

  • UART_RS485_CONF_REG.UART_RS485_EN: setting this bit enables RS485 communication mode support.

  • UART_RS485_CONF_REG.UART_RS485TX_RX_EN: if this bit is set, the transmitter’s output signal loops back to the receiver’s input signal.

  • UART_RS485_CONF_REG.UART_RS485RXBY_TX_EN: if this bit is set, the transmitter will still be sending data if the receiver is busy (remove collisions automatically by hardware).

The ESP32-S2’s RS485 UART hardware can detect signal collisions during transmission of a datagram and generate the interrupt UART_RS485_CLASH_INT if this interrupt is enabled. The term collision means that a transmitted datagram is not equal to the one received on the other end. Data collisions are usually associated with the presence of other active devices on the bus or might occur due to bus errors.

The collision detection feature allows handling collisions when their interrupts are activated and triggered. The interrupts UART_RS485_FRM_ERR_INT and UART_RS485_PARITY_ERR_INT can be used with the collision detection feature to control frame errors and parity bit errors accordingly in RS485 mode. This functionality is supported in the UART driver and can be used by selecting the UART_MODE_RS485_APP_CTRL mode (see the function uart_set_mode()).

The collision detection feature can work with circuit A and circuit C (see Section Interface Connection Options). In the case of using circuit A or B, the RTS pin connected to the DE pin of the bus driver should be controlled by the user application. Use the function uart_get_collision_flag() to check if the collision detection flag has been raised.

The ESP32-S2 UART controllers themselves do not support half-duplex communication as they cannot provide automatic control of the RTS pin connected to the ~RE/DE input of RS485 bus driver. However, half-duplex communication can be achieved via software control of the RTS pin by the UART driver. This can be enabled by selecting the UART_MODE_RS485_HALF_DUPLEX mode when calling uart_set_mode().

Once the host starts writing data to the Tx FIFO buffer, the UART driver automatically asserts the RTS pin (logic 1); once the last bit of the data has been transmitted, the driver de-asserts the RTS pin (logic 0). To use this mode, the software would have to disable the hardware flow control function. This mode works with all the used circuits shown below.

Interface Connection Options

This section provides example schematics to demonstrate the basic aspects of ESP32-S2’s RS485 interface connection.

注解

  • The schematics below do not necessarily contain all required elements.

  • The analog devices ADM483 & ADM2483 are examples of common RS485 transceivers and can be replaced with other similar transceivers.

Circuit A: Collision Detection Circuit

        VCC ---------------+
                           |
                   +-------x-------+
        RXD <------| R             |
                   |              B|----------<> B
        TXD ------>| D    ADM483   |
ESP                |               |     RS485 bus side
        RTS ------>| DE            |
                   |              A|----------<> A
              +----| /RE           |
              |    +-------x-------+
              |            |
             GND          GND

This circuit is preferable because it allows for collision detection and is quite simple at the same time. The receiver in the line driver is constantly enabled, which allows the UART to monitor the RS485 bus. Echo suppression is performed by the UART peripheral when the bit UART_RS485_CONF_REG.UART_RS485TX_RX_EN is enabled.

Circuit B: Manual Switching Transmitter/Receiver Without Collision Detection

        VCC ---------------+
                           |
                   +-------x-------+
        RXD <------| R             |
                   |              B|-----------<> B
        TXD ------>| D    ADM483   |
ESP                |               |     RS485 bus side
        RTS --+--->| DE            |
              |    |              A|-----------<> A
              +----| /RE           |
                   +-------x-------+
                           |
                          GND

This circuit does not allow for collision detection. It suppresses the null bytes that the hardware receives when the bit UART_RS485_CONF_REG.UART_RS485TX_RX_EN is set. The bit UART_RS485_CONF_REG.UART_RS485RXBY_TX_EN is not applicable in this case.

Circuit C: Auto Switching Transmitter/Receiver

 VCC1 <-------------------+-----------+           +-------------------+----> VCC2
               10K ____   |           |           |                   |
              +---|____|--+       +---x-----------x---+    10K ____   |
              |                   |                   |   +---|____|--+
RX <----------+-------------------| RXD               |   |
                   10K ____       |                  A|---+---------------<> A (+)
              +-------|____|------| PV    ADM2483     |   |    ____  120
              |   ____            |                   |   +---|____|---+  RS485 bus side
      VCC1 <--+--|____|--+------->| DE                |                |
              10K        |        |                  B|---+------------+--<> B (-)
                      ---+    +-->| /RE               |   |    ____
         10K          |       |   |                   |   +---|____|---+
        ____       | /-C      +---| TXD               |    10K         |
TX >---|____|--+_B_|/   NPN   |   |                   |                |
                   |\         |   +---x-----------x---+                |
                   | \-E      |       |           |                    |
                      |       |       |           |                    |
                     GND1    GND1    GND1        GND2                 GND2

This galvanically isolated circuit does not require RTS pin control by a software application or driver because it controls the transceiver direction automatically. However, it requires suppressing null bytes during transmission by setting UART_RS485_CONF_REG.UART_RS485RXBY_TX_EN to 1 and UART_RS485_CONF_REG.UART_RS485TX_RX_EN to 0. This setup can work in any RS485 UART mode or even in UART_MODE_UART.

Application Examples

The table below describes the code examples available in the directory peripherals/uart/.

Code Example

Description

peripherals/uart/uart_echo

Configuring UART settings, installing the UART driver, and reading/writing over the UART1 interface.

peripherals/uart/uart_events

Reporting various communication events, using pattern detection interrupts.

peripherals/uart/uart_async_rxtxtasks

Transmitting and receiving data in two separate FreeRTOS tasks over the same UART.

peripherals/uart/uart_select

Using synchronous I/O multiplexing for UART file descriptors.

peripherals/uart/uart_echo_rs485

Setting up UART driver to communicate over RS485 interface in half-duplex mode. This example is similar to peripherals/uart/uart_echo but allows communication through an RS485 interface chip connected to ESP32-S2 pins.

peripherals/uart/nmea0183_parser

Obtaining GPS information by parsing NMEA0183 statements received from GPS via the UART peripheral.

API Reference

Functions

esp_err_t uart_driver_install(uart_port_t uart_num, int rx_buffer_size, int tx_buffer_size, int queue_size, QueueHandle_t *uart_queue, int intr_alloc_flags)

Install UART driver and set the UART to the default configuration.

UART ISR handler will be attached to the same CPU core that this function is running on.

Note

Rx_buffer_size should be greater than UART_FIFO_LEN. Tx_buffer_size should be either zero or greater than UART_FIFO_LEN.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • rx_buffer_size: UART RX ring buffer size.

  • tx_buffer_size: UART TX ring buffer size. If set to zero, driver will not use TX buffer, TX function will block task until all data have been sent out.

  • queue_size: UART event queue size/depth.

  • uart_queue: UART event queue handle (out param). On success, a new queue handle is written here to provide access to UART events. If set to NULL, driver will not use an event queue.

  • intr_alloc_flags: Flags used to allocate the interrupt. One or multiple (ORred) ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info. Do not set ESP_INTR_FLAG_IRAM here (the driver’s ISR handler is not located in IRAM)

esp_err_t uart_driver_delete(uart_port_t uart_num)

Uninstall UART driver.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

bool uart_is_driver_installed(uart_port_t uart_num)

Checks whether the driver is installed or not.

Return

  • true driver is installed

  • false driver is not installed

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_set_word_length(uart_port_t uart_num, uart_word_length_t data_bit)

Set UART data bits.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • data_bit: UART data bits

esp_err_t uart_get_word_length(uart_port_t uart_num, uart_word_length_t *data_bit)

Get the UART data bit configuration.

Return

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*data_bit)

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • data_bit: Pointer to accept value of UART data bits.

esp_err_t uart_set_stop_bits(uart_port_t uart_num, uart_stop_bits_t stop_bits)

Set UART stop bits.

Return

  • ESP_OK Success

  • ESP_FAIL Fail

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • stop_bits: UART stop bits

esp_err_t uart_get_stop_bits(uart_port_t uart_num, uart_stop_bits_t *stop_bits)

Get the UART stop bit configuration.

Return

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*stop_bit)

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • stop_bits: Pointer to accept value of UART stop bits.

esp_err_t uart_set_parity(uart_port_t uart_num, uart_parity_t parity_mode)

Set UART parity mode.

Return

  • ESP_FAIL Parameter error

  • ESP_OK Success

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • parity_mode: the enum of uart parity configuration

esp_err_t uart_get_parity(uart_port_t uart_num, uart_parity_t *parity_mode)

Get the UART parity mode configuration.

Return

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*parity_mode)

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • parity_mode: Pointer to accept value of UART parity mode.

esp_err_t uart_set_baudrate(uart_port_t uart_num, uint32_t baudrate)

Set UART baud rate.

Return

  • ESP_FAIL Parameter error

  • ESP_OK Success

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • baudrate: UART baud rate.

esp_err_t uart_get_baudrate(uart_port_t uart_num, uint32_t *baudrate)

Get the UART baud rate configuration.

Return

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*baudrate)

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • baudrate: Pointer to accept value of UART baud rate

esp_err_t uart_set_line_inverse(uart_port_t uart_num, uint32_t inverse_mask)

Set UART line inverse mode.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • inverse_mask: Choose the wires that need to be inverted. Using the ORred mask of uart_signal_inv_t

esp_err_t uart_set_hw_flow_ctrl(uart_port_t uart_num, uart_hw_flowcontrol_t flow_ctrl, uint8_t rx_thresh)

Set hardware flow control.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • flow_ctrl: Hardware flow control mode

  • rx_thresh: Threshold of Hardware RX flow control (0 ~ UART_FIFO_LEN). Only when UART_HW_FLOWCTRL_RTS is set, will the rx_thresh value be set.

esp_err_t uart_set_sw_flow_ctrl(uart_port_t uart_num, bool enable, uint8_t rx_thresh_xon, uint8_t rx_thresh_xoff)

Set software flow control.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART_NUM_0, UART_NUM_1 or UART_NUM_2

  • enable: switch on or off

  • rx_thresh_xon: low water mark

  • rx_thresh_xoff: high water mark

esp_err_t uart_get_hw_flow_ctrl(uart_port_t uart_num, uart_hw_flowcontrol_t *flow_ctrl)

Get the UART hardware flow control configuration.

Return

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*flow_ctrl)

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • flow_ctrl: Option for different flow control mode.

esp_err_t uart_clear_intr_status(uart_port_t uart_num, uint32_t clr_mask)

Clear UART interrupt status.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • clr_mask: Bit mask of the interrupt status to be cleared.

esp_err_t uart_enable_intr_mask(uart_port_t uart_num, uint32_t enable_mask)

Set UART interrupt enable.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • enable_mask: Bit mask of the enable bits.

esp_err_t uart_disable_intr_mask(uart_port_t uart_num, uint32_t disable_mask)

Clear UART interrupt enable bits.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • disable_mask: Bit mask of the disable bits.

esp_err_t uart_enable_rx_intr(uart_port_t uart_num)

Enable UART RX interrupt (RX_FULL & RX_TIMEOUT INTERRUPT)

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_disable_rx_intr(uart_port_t uart_num)

Disable UART RX interrupt (RX_FULL & RX_TIMEOUT INTERRUPT)

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_disable_tx_intr(uart_port_t uart_num)

Disable UART TX interrupt (TXFIFO_EMPTY INTERRUPT)

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number

esp_err_t uart_enable_tx_intr(uart_port_t uart_num, int enable, int thresh)

Enable UART TX interrupt (TXFIFO_EMPTY INTERRUPT)

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • enable: 1: enable; 0: disable

  • thresh: Threshold of TX interrupt, 0 ~ UART_FIFO_LEN

esp_err_t uart_isr_register(uart_port_t uart_num, void (*fn)(void *), void *arg, int intr_alloc_flags, uart_isr_handle_t *handle, )

Register UART interrupt handler (ISR).

Note

UART ISR handler will be attached to the same CPU core that this function is running on.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • fn: Interrupt handler function.

  • arg: parameter for handler function

  • intr_alloc_flags: Flags used to allocate the interrupt. One or multiple (ORred) ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info.

  • handle: Pointer to return handle. If non-NULL, a handle for the interrupt will be returned here.

esp_err_t uart_isr_free(uart_port_t uart_num)

Free UART interrupt handler registered by uart_isr_register. Must be called on the same core as uart_isr_register was called.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_set_pin(uart_port_t uart_num, int tx_io_num, int rx_io_num, int rts_io_num, int cts_io_num)

Assign signals of a UART peripheral to GPIO pins.

Note

If the GPIO number configured for a UART signal matches one of the IOMUX signals for that GPIO, the signal will be connected directly via the IOMUX. Otherwise the GPIO and signal will be connected via the GPIO Matrix. For example, if on an ESP32 the call uart_set_pin(0, 1, 3, -1, -1) is performed, as GPIO1 is UART0’s default TX pin and GPIO3 is UART0’s default RX pin, both will be connected to respectively U0TXD and U0RXD through the IOMUX, totally bypassing the GPIO matrix. The check is performed on a per-pin basis. Thus, it is possible to have RX pin binded to a GPIO through the GPIO matrix, whereas TX is binded to its GPIO through the IOMUX.

Note

Internal signal can be output to multiple GPIO pads. Only one GPIO pad can connect with input signal.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • tx_io_num: UART TX pin GPIO number.

  • rx_io_num: UART RX pin GPIO number.

  • rts_io_num: UART RTS pin GPIO number.

  • cts_io_num: UART CTS pin GPIO number.

esp_err_t uart_set_rts(uart_port_t uart_num, int level)

Manually set the UART RTS pin level.

Note

UART must be configured with hardware flow control disabled.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • level: 1: RTS output low (active); 0: RTS output high (block)

esp_err_t uart_set_dtr(uart_port_t uart_num, int level)

Manually set the UART DTR pin level.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • level: 1: DTR output low; 0: DTR output high

esp_err_t uart_set_tx_idle_num(uart_port_t uart_num, uint16_t idle_num)

Set UART idle interval after tx FIFO is empty.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • idle_num: idle interval after tx FIFO is empty(unit: the time it takes to send one bit under current baudrate)

esp_err_t uart_param_config(uart_port_t uart_num, const uart_config_t *uart_config)

Set UART configuration parameters.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • uart_config: UART parameter settings

esp_err_t uart_intr_config(uart_port_t uart_num, const uart_intr_config_t *intr_conf)

Configure UART interrupts.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • intr_conf: UART interrupt settings

esp_err_t uart_wait_tx_done(uart_port_t uart_num, TickType_t ticks_to_wait)

Wait until UART TX FIFO is empty.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

  • ESP_ERR_TIMEOUT Timeout

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • ticks_to_wait: Timeout, count in RTOS ticks

int uart_tx_chars(uart_port_t uart_num, const char *buffer, uint32_t len)

Send data to the UART port from a given buffer and length.

This function will not wait for enough space in TX FIFO. It will just fill the available TX FIFO and return when the FIFO is full.

Note

This function should only be used when UART TX buffer is not enabled.

Return

  • (-1) Parameter error

  • OTHERS (>=0) The number of bytes pushed to the TX FIFO

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • buffer: data buffer address

  • len: data length to send

int uart_write_bytes(uart_port_t uart_num, const void *src, size_t size)

Send data to the UART port from a given buffer and length,.

If the UART driver’s parameter ‘tx_buffer_size’ is set to zero: This function will not return until all the data have been sent out, or at least pushed into TX FIFO.

Otherwise, if the ‘tx_buffer_size’ > 0, this function will return after copying all the data to tx ring buffer, UART ISR will then move data from the ring buffer to TX FIFO gradually.

Return

  • (-1) Parameter error

  • OTHERS (>=0) The number of bytes pushed to the TX FIFO

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • src: data buffer address

  • size: data length to send

int uart_write_bytes_with_break(uart_port_t uart_num, const void *src, size_t size, int brk_len)

Send data to the UART port from a given buffer and length,.

If the UART driver’s parameter ‘tx_buffer_size’ is set to zero: This function will not return until all the data and the break signal have been sent out. After all data is sent out, send a break signal.

Otherwise, if the ‘tx_buffer_size’ > 0, this function will return after copying all the data to tx ring buffer, UART ISR will then move data from the ring buffer to TX FIFO gradually. After all data sent out, send a break signal.

Return

  • (-1) Parameter error

  • OTHERS (>=0) The number of bytes pushed to the TX FIFO

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • src: data buffer address

  • size: data length to send

  • brk_len: break signal duration(unit: the time it takes to send one bit at current baudrate)

int uart_read_bytes(uart_port_t uart_num, void *buf, uint32_t length, TickType_t ticks_to_wait)

UART read bytes from UART buffer.

Return

  • (-1) Error

  • OTHERS (>=0) The number of bytes read from UART FIFO

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • buf: pointer to the buffer.

  • length: data length

  • ticks_to_wait: sTimeout, count in RTOS ticks

esp_err_t uart_flush(uart_port_t uart_num)

Alias of uart_flush_input. UART ring buffer flush. This will discard all data in the UART RX buffer.

Note

Instead of waiting the data sent out, this function will clear UART rx buffer. In order to send all the data in tx FIFO, we can use uart_wait_tx_done function.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_flush_input(uart_port_t uart_num)

Clear input buffer, discard all the data is in the ring-buffer.

Note

In order to send all the data in tx FIFO, we can use uart_wait_tx_done function.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_get_buffered_data_len(uart_port_t uart_num, size_t *size)

UART get RX ring buffer cached data length.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • size: Pointer of size_t to accept cached data length

esp_err_t uart_disable_pattern_det_intr(uart_port_t uart_num)

UART disable pattern detect function. Designed for applications like ‘AT commands’. When the hardware detects a series of one same character, the interrupt will be triggered.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_enable_pattern_det_baud_intr(uart_port_t uart_num, char pattern_chr, uint8_t chr_num, int chr_tout, int post_idle, int pre_idle)

UART enable pattern detect function. Designed for applications like ‘AT commands’. When the hardware detect a series of one same character, the interrupt will be triggered.

Return

  • ESP_OK Success

  • ESP_FAIL Parameter error

Parameters

  • uart_num: UART port number.

  • pattern_chr: character of the pattern.

  • chr_num: number of the character, 8bit value.

  • chr_tout: timeout of the interval between each pattern characters, 16bit value, unit is the baud-rate cycle you configured. When the duration is more than this value, it will not take this data as at_cmd char.

  • post_idle: idle time after the last pattern character, 16bit value, unit is the baud-rate cycle you configured. When the duration is less than this value, it will not take the previous data as the last at_cmd char

  • pre_idle: idle time before the first pattern character, 16bit value, unit is the baud-rate cycle you configured. When the duration is less than this value, it will not take this data as the first at_cmd char.

int uart_pattern_pop_pos(uart_port_t uart_num)

Return the nearest detected pattern position in buffer. The positions of the detected pattern are saved in a queue, this function will dequeue the first pattern position and move the pointer to next pattern position.

The following APIs will modify the pattern position info: uart_flush_input, uart_read_bytes, uart_driver_delete, uart_pop_pattern_pos It is the application’s responsibility to ensure atomic access to the pattern queue and the rx data buffer when using pattern detect feature.

Note

If the RX buffer is full and flow control is not enabled, the detected pattern may not be found in the rx buffer due to overflow.

Return

  • (-1) No pattern found for current index or parameter error

  • others the pattern position in rx buffer.

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

int uart_pattern_get_pos(uart_port_t uart_num)

Return the nearest detected pattern position in buffer. The positions of the detected pattern are saved in a queue, This function do nothing to the queue.

The following APIs will modify the pattern position info: uart_flush_input, uart_read_bytes, uart_driver_delete, uart_pop_pattern_pos It is the application’s responsibility to ensure atomic access to the pattern queue and the rx data buffer when using pattern detect feature.

Note

If the RX buffer is full and flow control is not enabled, the detected pattern may not be found in the rx buffer due to overflow.

Return

  • (-1) No pattern found for current index or parameter error

  • others the pattern position in rx buffer.

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

esp_err_t uart_pattern_queue_reset(uart_port_t uart_num, int queue_length)

Allocate a new memory with the given length to save record the detected pattern position in rx buffer.

Return

  • ESP_ERR_NO_MEM No enough memory

  • ESP_ERR_INVALID_STATE Driver not installed

  • ESP_FAIL Parameter error

  • ESP_OK Success

Parameters

  • uart_num: UART port number, the max port number is (UART_NUM_MAX -1).

  • queue_length: Max queue length for the detected pattern. If the queue length is not large enough, some pattern positions might be lost. Set this value to the maximum number of patterns that could be saved in data buffer at the same time.

esp_err_t uart_set_mode(uart_port_t uart_num, uart_mode_t mode)

UART set communication mode.

Note

This function must be executed after uart_driver_install(), when the driver object is initialized.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters

  • uart_num: Uart number to configure, the max port number is (UART_NUM_MAX -1).

  • mode: UART UART mode to set

esp_err_t uart_set_rx_full_threshold(uart_port_t uart_num, int threshold)

Set uart threshold value for RX fifo full.

Note

If application is using higher baudrate and it is observed that bytes in hardware RX fifo are overwritten then this threshold can be reduced

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_ERR_INVALID_STATE Driver is not installed

Parameters

  • uart_num: UART_NUM_0, UART_NUM_1 or UART_NUM_2

  • threshold: Threshold value above which RX fifo full interrupt is generated

esp_err_t uart_set_tx_empty_threshold(uart_port_t uart_num, int threshold)

Set uart threshold values for TX fifo empty.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_ERR_INVALID_STATE Driver is not installed

Parameters

  • uart_num: UART_NUM_0, UART_NUM_1 or UART_NUM_2

  • threshold: Threshold value below which TX fifo empty interrupt is generated

esp_err_t uart_set_rx_timeout(uart_port_t uart_num, const uint8_t tout_thresh)

UART set threshold timeout for TOUT feature.

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_ERR_INVALID_STATE Driver is not installed

Parameters

  • uart_num: Uart number to configure, the max port number is (UART_NUM_MAX -1).

  • tout_thresh: This parameter defines timeout threshold in uart symbol periods. The maximum value of threshold is 126. tout_thresh = 1, defines TOUT interrupt timeout equal to transmission time of one symbol (~11 bit) on current baudrate. If the time is expired the UART_RXFIFO_TOUT_INT interrupt is triggered. If tout_thresh == 0, the TOUT feature is disabled.

esp_err_t uart_get_collision_flag(uart_port_t uart_num, bool *collision_flag)

Returns collision detection flag for RS485 mode Function returns the collision detection flag into variable pointed by collision_flag. *collision_flag = true, if collision detected else it is equal to false. This function should be executed when actual transmission is completed (after uart_write_bytes()).

Return

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

Parameters

  • uart_num: Uart number to configure the max port number is (UART_NUM_MAX -1).

  • collision_flag: Pointer to variable of type bool to return collision flag.

esp_err_t uart_set_wakeup_threshold(uart_port_t uart_num, int wakeup_threshold)

Set the number of RX pin signal edges for light sleep wakeup.

UART can be used to wake up the system from light sleep. This feature works by counting the number of positive edges on RX pin and comparing the count to the threshold. When the count exceeds the threshold, system is woken up from light sleep. This function allows setting the threshold value.

Stop bit and parity bits (if enabled) also contribute to the number of edges. For example, letter ‘a’ with ASCII code 97 is encoded as 0100001101 on the wire (with 8n1 configuration), start and stop bits included. This sequence has 3 positive edges (transitions from 0 to 1). Therefore, to wake up the system when ‘a’ is sent, set wakeup_threshold=3.

The character that triggers wakeup is not received by UART (i.e. it can not be obtained from UART FIFO). Depending on the baud rate, a few characters after that will also not be received. Note that when the chip enters and exits light sleep mode, APB frequency will be changing. To make sure that UART has correct baud rate all the time, select REF_TICK as UART clock source, by setting use_ref_tick field in uart_config_t to true.

Note

in ESP32, the wakeup signal can only be input via IO_MUX (i.e. GPIO3 should be configured as function_1 to wake up UART0, GPIO9 should be configured as function_5 to wake up UART1), UART2 does not support light sleep wakeup feature.

Return

  • ESP_OK on success

  • ESP_ERR_INVALID_ARG if uart_num is incorrect or wakeup_threshold is outside of [3, 0x3ff] range.

Parameters

  • uart_num: UART number, the max port number is (UART_NUM_MAX -1).

  • wakeup_threshold: number of RX edges for light sleep wakeup, value is 3 .. 0x3ff.

esp_err_t uart_get_wakeup_threshold(uart_port_t uart_num, int *out_wakeup_threshold)

Get the number of RX pin signal edges for light sleep wakeup.

See description of uart_set_wakeup_threshold for the explanation of UART wakeup feature.

Return

  • ESP_OK on success

  • ESP_ERR_INVALID_ARG if out_wakeup_threshold is NULL

Parameters

  • uart_num: UART number, the max port number is (UART_NUM_MAX -1).

  • [out] out_wakeup_threshold: output, set to the current value of wakeup threshold for the given UART.

esp_err_t uart_wait_tx_idle_polling(uart_port_t uart_num)

Wait until UART tx memory empty and the last char send ok (polling mode).

  • Return

    • ESP_OK on success

    • ESP_ERR_INVALID_ARG Parameter error

    • ESP_FAIL Driver not installed

Parameters

  • uart_num: UART number

esp_err_t uart_set_loop_back(uart_port_t uart_num, bool loop_back_en)

Configure TX signal loop back to RX module, just for the test usage.

  • Return

    • ESP_OK on success

    • ESP_ERR_INVALID_ARG Parameter error

    • ESP_FAIL Driver not installed

Parameters

  • uart_num: UART number

  • loop_back_en: Set ture to enable the loop back function, else set it false.

void uart_set_always_rx_timeout(uart_port_t uart_num, bool always_rx_timeout_en)

Configure behavior of UART RX timeout interrupt.

When always_rx_timeout is true, timeout interrupt is triggered even if FIFO is full. This function can cause extra timeout interrupts triggered only to send the timeout event. Call this function only if you want to ensure timeout interrupt will always happen after a byte stream.

Parameters

  • uart_num: UART number

  • always_rx_timeout_en: Set to false enable the default behavior of timeout interrupt, set it to true to always trigger timeout interrupt.

Structures

struct uart_intr_config_t

UART interrupt configuration parameters for uart_intr_config function.

Public Members

uint32_t intr_enable_mask

UART interrupt enable mask, choose from UART_XXXX_INT_ENA_M under UART_INT_ENA_REG(i), connect with bit-or operator

uint8_t rx_timeout_thresh

UART timeout interrupt threshold (unit: time of sending one byte)

uint8_t txfifo_empty_intr_thresh

UART TX empty interrupt threshold.

uint8_t rxfifo_full_thresh

UART RX full interrupt threshold.

struct uart_event_t

Event structure used in UART event queue.

Public Members

uart_event_type_t type

UART event type

size_t size

UART data size for UART_DATA event

bool timeout_flag

UART data read timeout flag for UART_DATA event (no new data received during configured RX TOUT) If the event is caused by FIFO-full interrupt, then there will be no event with the timeout flag before the next byte coming.

Macros

UART_NUM_0

UART port 0

UART_NUM_1

UART port 1

UART_NUM_MAX

UART port max

UART_PIN_NO_CHANGE
UART_FIFO_LEN

Length of the UART HW FIFO.

UART_BITRATE_MAX

Maximum configurable bitrate.

Type Definitions

typedef intr_handle_t uart_isr_handle_t

Enumerations

enum uart_event_type_t

UART event types used in the ring buffer.

Values:

UART_DATA

UART data event

UART_BREAK

UART break event

UART_BUFFER_FULL

UART RX buffer full event

UART_FIFO_OVF

UART FIFO overflow event

UART_FRAME_ERR

UART RX frame error event

UART_PARITY_ERR

UART RX parity event

UART_DATA_BREAK

UART TX data and break event

UART_PATTERN_DET

UART pattern detected

UART_EVENT_MAX

UART event max index

Structures

struct uart_at_cmd_t

UART AT cmd char configuration parameters Note that this function may different on different chip. Please refer to the TRM at confirguration.

Public Members

uint8_t cmd_char

UART AT cmd char

uint8_t char_num

AT cmd char repeat number

uint32_t gap_tout

gap time(in baud-rate) between AT cmd char

uint32_t pre_idle

the idle time(in baud-rate) between the non AT char and first AT char

uint32_t post_idle

the idle time(in baud-rate) between the last AT char and the none AT char

struct uart_sw_flowctrl_t

UART software flow control configuration parameters.

Public Members

uint8_t xon_char

Xon flow control char

uint8_t xoff_char

Xoff flow control char

uint8_t xon_thrd

If the software flow control is enabled and the data amount in rxfifo is less than xon_thrd, an xon_char will be sent

uint8_t xoff_thrd

If the software flow control is enabled and the data amount in rxfifo is more than xoff_thrd, an xoff_char will be sent

struct uart_config_t

UART configuration parameters for uart_param_config function.

Public Members

int baud_rate

UART baud rate

uart_word_length_t data_bits

UART byte size

uart_parity_t parity

UART parity mode

uart_stop_bits_t stop_bits

UART stop bits

uart_hw_flowcontrol_t flow_ctrl

UART HW flow control mode (cts/rts)

uint8_t rx_flow_ctrl_thresh

UART HW RTS threshold

uart_sclk_t source_clk

UART source clock selection

bool use_ref_tick

Deprecated method to select ref tick clock source, set source_clk field instead

Type Definitions

typedef int uart_port_t

UART port number, can be UART_NUM_0 ~ (UART_NUM_MAX -1).

Enumerations

enum uart_mode_t

UART mode selection.

Values:

UART_MODE_UART = 0x00

mode: regular UART mode

UART_MODE_RS485_HALF_DUPLEX = 0x01

mode: half duplex RS485 UART mode control by RTS pin

UART_MODE_IRDA = 0x02

mode: IRDA UART mode

UART_MODE_RS485_COLLISION_DETECT = 0x03

mode: RS485 collision detection UART mode (used for test purposes)

UART_MODE_RS485_APP_CTRL = 0x04

mode: application control RS485 UART mode (used for test purposes)

enum uart_word_length_t

UART word length constants.

Values:

UART_DATA_5_BITS = 0x0

word length: 5bits

UART_DATA_6_BITS = 0x1

word length: 6bits

UART_DATA_7_BITS = 0x2

word length: 7bits

UART_DATA_8_BITS = 0x3

word length: 8bits

UART_DATA_BITS_MAX = 0x4
enum uart_stop_bits_t

UART stop bits number.

Values:

UART_STOP_BITS_1 = 0x1

stop bit: 1bit

UART_STOP_BITS_1_5 = 0x2

stop bit: 1.5bits

UART_STOP_BITS_2 = 0x3

stop bit: 2bits

UART_STOP_BITS_MAX = 0x4
enum uart_parity_t

UART parity constants.

Values:

UART_PARITY_DISABLE = 0x0

Disable UART parity

UART_PARITY_EVEN = 0x2

Enable UART even parity

UART_PARITY_ODD = 0x3

Enable UART odd parity

enum uart_hw_flowcontrol_t

UART hardware flow control modes.

Values:

UART_HW_FLOWCTRL_DISABLE = 0x0

disable hardware flow control

UART_HW_FLOWCTRL_RTS = 0x1

enable RX hardware flow control (rts)

UART_HW_FLOWCTRL_CTS = 0x2

enable TX hardware flow control (cts)

UART_HW_FLOWCTRL_CTS_RTS = 0x3

enable hardware flow control

UART_HW_FLOWCTRL_MAX = 0x4
enum uart_signal_inv_t

UART signal bit map.

Values:

UART_SIGNAL_INV_DISABLE = 0

Disable UART signal inverse

UART_SIGNAL_IRDA_TX_INV = (0x1 << 0)

inverse the UART irda_tx signal

UART_SIGNAL_IRDA_RX_INV = (0x1 << 1)

inverse the UART irda_rx signal

UART_SIGNAL_RXD_INV = (0x1 << 2)

inverse the UART rxd signal

UART_SIGNAL_CTS_INV = (0x1 << 3)

inverse the UART cts signal

UART_SIGNAL_DSR_INV = (0x1 << 4)

inverse the UART dsr signal

UART_SIGNAL_TXD_INV = (0x1 << 5)

inverse the UART txd signal

UART_SIGNAL_RTS_INV = (0x1 << 6)

inverse the UART rts signal

UART_SIGNAL_DTR_INV = (0x1 << 7)

inverse the UART dtr signal

enum uart_sclk_t

UART source clock.

Values:

UART_SCLK_APB = 0x0

UART source clock from APB

UART_SCLK_REF_TICK = 0x3

UART source clock from REF_TICK

GPIO Lookup Macros

The UART peripherals have dedicated IO_MUX pins to which they are connected directly. However, signals can also be routed to other pins using the less direct GPIO matrix. To use direct routes, you need to know which pin is a dedicated IO_MUX pin for a UART channel. GPIO Lookup Macros simplify the process of finding and assigning IO_MUX pins. You choose a macro based on either the IO_MUX pin number, or a required UART channel name, and the macro will return the matching counterpart for you. See some examples below.

注解

These macros are useful if you need very high UART baud rates (over 40 MHz), which means you will have to use IO_MUX pins only. In other cases, these macros can be ignored, and you can use the GPIO Matrix as it allows you to configure any GPIO pin for any UART function.

  1. UART_NUM_2_TXD_DIRECT_GPIO_NUM returns the IO_MUX pin number of UART channel 2 TXD pin (pin 17)

  2. UART_GPIO19_DIRECT_CHANNEL returns the UART number of GPIO 19 when connected to the UART peripheral via IO_MUX (this is UART_NUM_0)

  3. UART_CTS_GPIO19_DIRECT_CHANNEL returns the UART number of GPIO 19 when used as the UART CTS pin via IO_MUX (this is UART_NUM_0). Similar to the above macro but specifies the pin function which is also part of the IO_MUX assignment.

Macros

UART_GPIO43_DIRECT_CHANNEL
UART_NUM_0_TXD_DIRECT_GPIO_NUM
UART_GPIO44_DIRECT_CHANNEL
UART_NUM_0_RXD_DIRECT_GPIO_NUM
UART_GPIO16_DIRECT_CHANNEL
UART_NUM_0_CTS_DIRECT_GPIO_NUM
UART_GPIO15_DIRECT_CHANNEL
UART_NUM_0_RTS_DIRECT_GPIO_NUM
UART_TXD_GPIO43_DIRECT_CHANNEL
UART_RXD_GPIO44_DIRECT_CHANNEL
UART_CTS_GPIO16_DIRECT_CHANNEL
UART_RTS_GPIO15_DIRECT_CHANNEL
UART_GPIO17_DIRECT_CHANNEL
UART_NUM_1_TXD_DIRECT_GPIO_NUM
UART_GPIO18_DIRECT_CHANNEL
UART_NUM_1_RXD_DIRECT_GPIO_NUM
UART_GPIO20_DIRECT_CHANNEL
UART_NUM_1_CTS_DIRECT_GPIO_NUM
UART_GPIO19_DIRECT_CHANNEL
UART_NUM_1_RTS_DIRECT_GPIO_NUM
UART_TXD_GPIO17_DIRECT_CHANNEL
UART_RXD_GPIO18_DIRECT_CHANNEL
UART_CTS_GPIO20_DIRECT_CHANNEL
UART_RTS_GPIO19_DIRECT_CHANNEL

提供有关此文档的反馈