I2C 接口的 LCD

[English]

  1. 创建 I2C 总线。详细信息,请参阅 I2C API 文档

    i2c_master_bus_handle_t i2c_bus = NULL;
    i2c_master_bus_config_t bus_config = {
        .clk_source = I2C_CLK_SRC_DEFAULT,
        .glitch_ignore_cnt = 7,
        .i2c_port = I2C_BUS_PORT,
        .sda_io_num = EXAMPLE_PIN_NUM_SDA,
        .scl_io_num = EXAMPLE_PIN_NUM_SCL,
        .flags.enable_internal_pullup = true,
    };
    ESP_ERROR_CHECK(i2c_new_master_bus(&bus_config, &i2c_bus));
    
  2. 从 I2C 总线分配一个 LCD IO 设备句柄。在此步骤中,需要提供以下信息:

    esp_lcd_panel_io_handle_t io_handle = NULL;
    esp_lcd_panel_io_i2c_config_t io_config = {
        .dev_addr = EXAMPLE_I2C_HW_ADDR,
        .scl_speed_hz = EXAMPLE_LCD_PIXEL_CLOCK_HZ,
        .control_phase_bytes = 1, // 参阅 LCD 规格
        .dc_bit_offset = 6,       // 参阅 LCD 规格
        .lcd_cmd_bits = EXAMPLE_LCD_CMD_BITS,
        .lcd_param_bits = EXAMPLE_LCD_CMD_BITS,
    };
    ESP_ERROR_CHECK(esp_lcd_new_panel_io_i2c(i2c_bus, &io_config, &io_handle));
    
  3. 安装 LCD 控制器驱动程序。LCD 控制器驱动程序负责向 LCD 控制器芯片发送命令和参数。在此步骤中,需要指定上一步骤中分配到的 I2C IO 设备句柄以及一些面板特定配置:

    • esp_lcd_panel_dev_config_t::reset_gpio_num 设置 LCD 的硬件复位 GPIO 编号。如果 LCD 没有硬件复位管脚,则将此设置为 -1

    • esp_lcd_panel_dev_config_t::bits_per_pixel 设置像素颜色数据的位宽。LCD 驱动程序使用此值计算要发送到 LCD 控制器芯片的字节数。

    esp_lcd_panel_handle_t panel_handle = NULL;
    esp_lcd_panel_dev_config_t panel_config = {
        .bits_per_pixel = 1,
        .reset_gpio_num = EXAMPLE_PIN_NUM_RST,
    };
    ESP_ERROR_CHECK(esp_lcd_new_panel_ssd1306(io_handle, &panel_config, &panel_handle));
    

API 参考

Header File

  • components/esp_lcd/include/esp_lcd_io_i2c.h

  • This header file can be included with:

    #include "esp_lcd_io_i2c.h"
    
  • This header file is a part of the API provided by the esp_lcd component. To declare that your component depends on esp_lcd, add the following to your CMakeLists.txt:

    REQUIRES esp_lcd
    

    or

    PRIV_REQUIRES esp_lcd
    

Functions

esp_err_t esp_lcd_new_panel_io_i2c_v1(uint32_t bus, const esp_lcd_panel_io_i2c_config_t *io_config, esp_lcd_panel_io_handle_t *ret_io)

Create LCD panel IO handle, for I2C interface in legacy implementation.

备注

Please don't call this function in your project directly. Please call esp_lcd_new_panel_to_i2c instead.

参数
  • bus -- [in] I2C bus handle, (in uint32_t)

  • io_config -- [in] IO configuration, for I2C interface

  • ret_io -- [out] Returned IO handle

返回

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_NO_MEM if out of memory

  • ESP_OK on success

esp_err_t esp_lcd_new_panel_io_i2c_v2(i2c_master_bus_handle_t bus, const esp_lcd_panel_io_i2c_config_t *io_config, esp_lcd_panel_io_handle_t *ret_io)

Create LCD panel IO handle, for I2C interface in new implementation.

备注

Please don't call this function in your project directly. Please call esp_lcd_new_panel_to_i2c instead.

参数
  • bus -- [in] I2C bus handle, (in i2c_master_dev_handle_t)

  • io_config -- [in] IO configuration, for I2C interface

  • ret_io -- [out] Returned IO handle

返回

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_NO_MEM if out of memory

  • ESP_OK on success

Structures

struct esp_lcd_panel_io_i2c_config_t

Panel IO configuration structure, for I2C interface.

Public Members

uint32_t dev_addr

I2C device address

esp_lcd_panel_io_color_trans_done_cb_t on_color_trans_done

Callback invoked when color data transfer has finished

void *user_ctx

User private data, passed directly to on_color_trans_done's user_ctx

size_t control_phase_bytes

I2C LCD panel will encode control information (e.g. D/C selection) into control phase, in several bytes

unsigned int dc_bit_offset

Offset of the D/C selection bit in control phase

int lcd_cmd_bits

Bit-width of LCD command

int lcd_param_bits

Bit-width of LCD parameter

unsigned int dc_low_on_data

If this flag is enabled, DC line = 0 means transfer data, DC line = 1 means transfer command; vice versa

unsigned int disable_control_phase

If this flag is enabled, the control phase isn't used

struct esp_lcd_panel_io_i2c_config_t::[anonymous] flags

Extra flags to fine-tune the I2C device

uint32_t scl_speed_hz

I2C LCD SCL frequency (hz)

Macros

esp_lcd_new_panel_io_i2c(bus, io_config, ret_io)

Create LCD panel IO handle.

参数
  • bus -- [in] I2C bus handle

  • io_config -- [in] IO configuration, for I2C interface

  • ret_io -- [out] Returned IO handle

返回

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_NO_MEM if out of memory

  • ESP_OK on success

Type Definitions

typedef uint32_t esp_lcd_i2c_bus_handle_t

Type of LCD I2C bus handle


此文档对您有帮助吗?