Watchdogs

[中文]

Overview

ESP-IDF supports multiple types of watchdogs:

  • Hardware Watchdog Timers

  • Interrupt Watchdog Timer (IWDT)

  • Task Watchdog Timer (TWDT)

The Interrupt Watchdog is responsible for ensuring that ISRs (Interrupt Service Routines) are not blocked for a prolonged period of time. The TWDT is responsible for detecting instances of tasks running without yielding for a prolonged period.

The various watchdog timers can be enabled using the Editing the Configuration. However, the TWDT can also be enabled during runtime.

Hardware Watchdog Timers

The chips have two groups of watchdog timers:

  • Main System Watchdog Timer (MWDT_WDT) - used by Interrupt Watchdog Timer (IWDT) and Task Watchdog Timer (TWDT).

  • RTC Watchdog Timer (RTC_WDT) - used to track the boot time from power-up until the user's main function (by default RTC Watchdog is disabled immediately before the user's main function).

Refer to the Watchdog section to understand how watchdogs are utilized in the bootloader.

The app's behaviour can be adjusted so the RTC Watchdog remains enabled after app startup. The Watchdog would need to be explicitly reset (i.e., fed) or disabled by the app to avoid the chip reset. To do this, set the CONFIG_BOOTLOADER_WDT_DISABLE_IN_USER_CODE option, modify the app as needed, and then recompile the app. In this case, the following APIs should be used:

If RTC_WDT is not reset/disabled in time, the chip will be automatically reset. See RTC Watchdog Timeout for more information.

Interrupt Watchdog Timer (IWDT)

The purpose of the IWDT is to ensure that interrupt service routines (ISRs) are not blocked from running for a prolonged period of time (i.e., the IWDT timeout period). Preventing ISRs from running in a timely manner is undesirable as it can increase ISR latency, and also prevent task switching (as task switching is executed form an ISR). The things that can block ISRs from running include:

  • Disabling interrupts

  • Critical Sections (also disables interrupts)

  • Other same/higher priority ISRs which block same/lower priority ISRs from running

The IWDT utilizes the MWDT_WDT watchdog timer in Timer Group 1 as its underlying hardware timer and leverages the FreeRTOS tick interrupt on each CPU to feed the watchdog timer. If the tick interrupt on a particular CPU is not run at within the IWDT timeout period, it is indicative that something is blocking ISRs from being run on that CPU (see the list of reasons above).

When the IWDT times out, the default action is to invoke the panic handler and display the panic reason as Interrupt wdt timeout on CPU0 or Interrupt wdt timeout on CPU1 (as applicable). Depending on the panic handler's configured behavior (see CONFIG_ESP_SYSTEM_PANIC), users can then debug the source of the IWDT timeout (via the backtrace, OpenOCD, gdbstub etc) or simply reset the chip (which may be preferred in a production environment).

If for whatever reason the panic handler is unable to run after an IWDT timeout, the IWDT has a second stage timeout that will hard-reset the chip (i.e., a system reset).

Configuration

  • The IWDT is enabled by default via the CONFIG_ESP_INT_WDT option.

  • The IWDT's timeout is configured by setting the CONFIG_ESP_INT_WDT_TIMEOUT_MS option.

    • Note that the default timeout is higher if PSRAM support is enabled, as a critical section or interrupt routine that accesses a large amount of PSRAM takes longer to complete in some circumstances.

    • The timeout should always at least twice longer than the period between FreeRTOS ticks (see CONFIG_FREERTOS_HZ).

Tuning

If you find the IWDT timeout is triggered because an interrupt or critical section is running longer than the timeout period, consider rewriting the code:

  • Critical sections should be made as short as possible. Any non-critical code/computation should be placed outside the critical section.

  • Interrupt handlers should also perform the minimum possible amount of computation. Users can consider deferring any computation to a task by having the ISR push data to a task using queues.

Neither critical sections or interrupt handlers should ever block waiting for another event to occur. If changing the code to reduce the processing time is not possible or desirable, it is possible to increase the CONFIG_ESP_INT_WDT_TIMEOUT_MS setting instead.

Task Watchdog Timer (TWDT)

The Task Watchdog Timer (TWDT) is used to monitor particular tasks, ensuring that they are able to execute within a given timeout period. The TWDT primarily watches the Idle Tasks of each CPU, however any task can subscribe to be watched by the TWDT. By watching the Idle Tasks of each CPU, the TWDT can detect instances of tasks running for a prolonged period of time without yielding. This can be an indicator of poorly written code that spinloops on a peripheral, or a task that is stuck in an infinite loop.

The TWDT is built around the MWDT_WDT watchdog timer in Timer Group 0. When a timeout occurs, an interrupt is triggered.

Users can define the function esp_task_wdt_isr_user_handler in the user code, in order to receive the timeout event and extend the default behavior.

Usage

The following functions can be used to watch tasks using the TWDT:

In the case where applications need to watch at a more granular level (i.e., ensure that a particular functions/stub/code-path is called), the TWDT allows subscription of users.

Configuration

The default timeout period for the TWDT is set using config item CONFIG_ESP_TASK_WDT_TIMEOUT_S. This should be set to at least as long as you expect any single task needs to monopolize the CPU (for example, if you expect the app will do a long intensive calculation and should not yield to other tasks). It is also possible to change this timeout at runtime by calling esp_task_wdt_init().

Note

Erasing large flash areas can be time consuming and can cause a task to run continuously, thus triggering a TWDT timeout. The following two methods can be used to avoid this:

For more information, you can refer to SPI Flash API.

The following config options control TWDT configuration. They are all enabled by default:

Note

On a TWDT timeout the default behaviour is to simply print a warning and a backtrace before continuing running the app. If you want a timeout to cause a panic and a system reset then this can be configured through CONFIG_ESP_TASK_WDT_PANIC.

JTAG & Watchdogs

While debugging using OpenOCD, the CPUs are halted every time a breakpoint is reached. However if the watchdog timers continue to run when a breakpoint is encountered, they will eventually trigger a reset making it very difficult to debug code. Therefore OpenOCD will disable the hardware timers of both the interrupt and task watchdogs at every breakpoint. Moreover, OpenOCD will not re-enable them upon leaving the breakpoint. This means that interrupt watchdog and task watchdog functionality will essentially be disabled. No warnings or panics from either watchdogs will be generated when the ESP32-C6 is connected to OpenOCD via JTAG.

Application Examples

  • system/task_watchdog demonstrates how to initialize, subscribe and unsubscribe tasks and users to the task watchdog, and how tasks and users can reset (feed) the task watchdog.

API Reference

Header File

Functions

esp_err_t esp_task_wdt_init(const esp_task_wdt_config_t *config)

Initialize the Task Watchdog Timer (TWDT)

This function configures and initializes the TWDT. This function will subscribe the idle tasks if configured to do so. For other tasks, users can subscribe them using esp_task_wdt_add() or esp_task_wdt_add_user(). This function won't start the timer if no task have been registered yet.

Note

esp_task_wdt_init() must only be called after the scheduler is started. Moreover, it must not be called by multiple tasks simultaneously.

Parameters

config -- [in] Configuration structure

Returns

  • ESP_OK: Initialization was successful

  • ESP_ERR_INVALID_STATE: Already initialized

  • Other: Failed to initialize TWDT

esp_err_t esp_task_wdt_reconfigure(const esp_task_wdt_config_t *config)

Reconfigure the Task Watchdog Timer (TWDT)

The function reconfigures the running TWDT. It must already be initialized when this function is called.

Note

esp_task_wdt_reconfigure() must not be called by multiple tasks simultaneously.

Parameters

config -- [in] Configuration structure

Returns

  • ESP_OK: Reconfiguring was successful

  • ESP_ERR_INVALID_STATE: TWDT not initialized yet

  • Other: Failed to initialize TWDT

esp_err_t esp_task_wdt_deinit(void)

Deinitialize the Task Watchdog Timer (TWDT)

This function will deinitialize the TWDT, and unsubscribe any idle tasks. Calling this function whilst other tasks are still subscribed to the TWDT, or when the TWDT is already deinitialized, will result in an error code being returned.

Note

esp_task_wdt_deinit() must not be called by multiple tasks simultaneously.

Returns

  • ESP_OK: TWDT successfully deinitialized

  • Other: Failed to deinitialize TWDT

esp_err_t esp_task_wdt_add(TaskHandle_t task_handle)

Subscribe a task to the Task Watchdog Timer (TWDT)

This function subscribes a task to the TWDT. Each subscribed task must periodically call esp_task_wdt_reset() to prevent the TWDT from elapsing its timeout period. Failure to do so will result in a TWDT timeout.

Parameters

task_handle -- Handle of the task. Input NULL to subscribe the current running task to the TWDT

Returns

  • ESP_OK: Successfully subscribed the task to the TWDT

  • Other: Failed to subscribe task

esp_err_t esp_task_wdt_add_user(const char *user_name, esp_task_wdt_user_handle_t *user_handle_ret)

Subscribe a user to the Task Watchdog Timer (TWDT)

This function subscribes a user to the TWDT. A user of the TWDT is usually a function that needs to run periodically. Each subscribed user must periodically call esp_task_wdt_reset_user() to prevent the TWDT from elapsing its timeout period. Failure to do so will result in a TWDT timeout.

Parameters

  • user_name -- [in] String to identify the user

  • user_handle_ret -- [out] Handle of the user

Returns

  • ESP_OK: Successfully subscribed the user to the TWDT

  • Other: Failed to subscribe user

esp_err_t esp_task_wdt_reset(void)

Reset the Task Watchdog Timer (TWDT) on behalf of the currently running task.

This function will reset the TWDT on behalf of the currently running task. Each subscribed task must periodically call this function to prevent the TWDT from timing out. If one or more subscribed tasks fail to reset the TWDT on their own behalf, a TWDT timeout will occur.

Returns

  • ESP_OK: Successfully reset the TWDT on behalf of the currently running task

  • Other: Failed to reset

esp_err_t esp_task_wdt_reset_user(esp_task_wdt_user_handle_t user_handle)

Reset the Task Watchdog Timer (TWDT) on behalf of a user.

This function will reset the TWDT on behalf of a user. Each subscribed user must periodically call this function to prevent the TWDT from timing out. If one or more subscribed users fail to reset the TWDT on their own behalf, a TWDT timeout will occur.

Parameters

user_handle -- [in] User handle

  • ESP_OK: Successfully reset the TWDT on behalf of the user

  • Other: Failed to reset

esp_err_t esp_task_wdt_delete(TaskHandle_t task_handle)

Unsubscribes a task from the Task Watchdog Timer (TWDT)

This function will unsubscribe a task from the TWDT. After being unsubscribed, the task should no longer call esp_task_wdt_reset().

Parameters

task_handle -- [in] Handle of the task. Input NULL to unsubscribe the current running task.

Returns

  • ESP_OK: Successfully unsubscribed the task from the TWDT

  • Other: Failed to unsubscribe task

esp_err_t esp_task_wdt_delete_user(esp_task_wdt_user_handle_t user_handle)

Unsubscribes a user from the Task Watchdog Timer (TWDT)

This function will unsubscribe a user from the TWDT. After being unsubscribed, the user should no longer call esp_task_wdt_reset_user().

Parameters

user_handle -- [in] User handle

Returns

  • ESP_OK: Successfully unsubscribed the user from the TWDT

  • Other: Failed to unsubscribe user

esp_err_t esp_task_wdt_status(TaskHandle_t task_handle)

Query whether a task is subscribed to the Task Watchdog Timer (TWDT)

This function will query whether a task is currently subscribed to the TWDT, or whether the TWDT is initialized.

Parameters

task_handle -- [in] Handle of the task. Input NULL to query the current running task.

Returns

:

  • ESP_OK: The task is currently subscribed to the TWDT

  • ESP_ERR_NOT_FOUND: The task is not subscribed

  • ESP_ERR_INVALID_STATE: TWDT was never initialized

void esp_task_wdt_isr_user_handler(void)

User ISR callback placeholder.

This function is called by task_wdt_isr function (ISR for when TWDT times out). It can be defined in user code to handle TWDT events.

Note

It has the same limitations as the interrupt function. Do not use ESP_LOGx functions inside.

esp_err_t esp_task_wdt_print_triggered_tasks(task_wdt_msg_handler msg_handler, void *opaque, int *cpus_fail)

Prints or retrieves information about tasks/users that triggered the Task Watchdog Timeout.

This function provides various operations to handle tasks/users that did not reset the Task Watchdog in time. It can print detailed information about these tasks/users, such as their names, associated CPUs, and whether they have been reset. Additionally, it can retrieve the total length of the printed information or the CPU affinity of the failing tasks.

Note

  • If msg_handler is not provided, the information will be printed to console using ESP_EARLY_LOGE.

  • If msg_handler is provided, the function will send the printed information to the provided message handler function.

  • If cpus_fail is provided, the function will store the CPU affinity of the failing tasks in the provided integer.

  • During the execution of this function, logging is allowed in critical sections, as TWDT timeouts are considered fatal errors.

Parameters

  • msg_handler -- [in] Optional message handler function that will be called for each printed line.

  • opaque -- [in] Optional pointer to opaque data that will be passed to the message handler function.

  • cpus_fail -- [out] Optional pointer to an integer where the CPU affinity of the failing tasks will be stored.

Returns

  • ESP_OK: The function executed successfully.

  • ESP_FAIL: No triggered tasks were found, and thus no information was printed or retrieved.

Structures

struct esp_task_wdt_config_t

Task Watchdog Timer (TWDT) configuration structure.

Public Members

uint32_t timeout_ms

TWDT timeout duration in milliseconds

uint32_t idle_core_mask

Bitmask of the core whose idle task should be subscribed on initialization where 1 << i means that core i's idle task will be monitored by the TWDT

bool trigger_panic

Trigger panic when timeout occurs

Type Definitions

typedef struct esp_task_wdt_user_handle_s *esp_task_wdt_user_handle_t

Task Watchdog Timer (TWDT) user handle.

typedef void (*task_wdt_msg_handler)(void *opaque, const char *msg)

Was this page helpful?