Universal Asynchronous Receiver/Transmitter (UART)

[中文]

Introduction

A Universal Asynchronous Receiver/Transmitter (UART) is a hardware feature that handles communication (i.e., timing requirements and data framing) using widely-adopted asynchronous serial communication interfaces, such as RS232, RS422, and RS485. A UART provides a widely adopted and cheap method to realize full-duplex or half-duplex data exchange among different devices.

The ESP32-P4 chip has 5 UART controllers (also referred to as port), each featuring an identical set of registers to simplify programming and for more flexibility.

Each UART controller is independently configurable with parameters such as baud rate, data bit length, bit ordering, number of stop bits, parity bit, etc. All the regular UART controllers are compatible with UART-enabled devices from various manufacturers and can also support Infrared Data Association (IrDA) protocols.

Additionally, the ESP32-P4 chip has one low-power (LP) UART controller. It is the cut-down version of regular UART. Usually, the LP UART controller only support basic UART functionality with a much smaller RAM size, and does not support IrDA or RS485 protocols. For a full list of difference between UART and LP UART, please refer to the ESP32-P4 Technical Reference Manual > UART Controller (UART) > Features [PDF]).

Functional Overview

The overview describes how to establish communication between an ESP32-P4 and other UART devices using the functions and data types of the UART driver. A typical programming workflow is broken down into the sections provided below:

  1. Set Communication Parameters - Setting baud rate, data bits, stop bits, etc.

  2. Set Communication Pins - Assigning pins for connection to a device

  3. Install Drivers - Allocating ESP32-P4's resources for the UART driver

  4. Run UART Communication - Sending/receiving data

  5. Use Interrupts - Triggering interrupts on specific communication events

  6. Deleting a Driver - Freeing allocated resources if a UART communication is no longer required

Steps 1 to 3 comprise the configuration stage. Step 4 is where the UART starts operating. Steps 5 and 6 are optional.

Additionally, when using the LP UART Controller you need to pay attention to Use LP UART Controller with HP Core.

The UART driver's functions identify each of the UART controllers using uart_port_t. This identification is needed for all the following function calls.

Set Communication Parameters

UART communication parameters can be configured all in a single step or individually in multiple steps.

Single Step

Call the function uart_param_config() and pass to it a uart_config_t structure. The uart_config_t structure should contain all the required parameters. See the example below.

const uart_port_t uart_num = UART_NUM_1;
uart_config_t uart_config = {
    .baud_rate = 115200,
    .data_bits = UART_DATA_8_BITS,
    .parity = UART_PARITY_DISABLE,
    .stop_bits = UART_STOP_BITS_1,
    .flow_ctrl = UART_HW_FLOWCTRL_CTS_RTS,
    .rx_flow_ctrl_thresh = 122,
};
// Configure UART parameters
ESP_ERROR_CHECK(uart_param_config(uart_num, &uart_config));

For more information on how to configure the hardware flow control options, please refer to peripherals/uart/uart_echo.

Additionally, uart_config_t::backup_before_sleep can be set to enable the backup of the UART configuration registers before entering sleep and restore these registers after exiting sleep. This allows the UART to continue working properly after waking up even when the UART module power domain is entirely off during sleep. This option implies an balance between power consumption and memory usage. If the power consumption is not a concern, you can disable this option to save memory.

Multiple Steps

Configure specific parameters individually by calling a dedicated function from the table given below. These functions are also useful if re-configuring a single parameter.

Functions for Configuring specific parameters individually

Parameter to Configure

Function

Baud rate

uart_set_baudrate()

Number of transmitted bits

uart_set_word_length() selected out of uart_word_length_t

Parity control

uart_set_parity() selected out of uart_parity_t

Number of stop bits

uart_set_stop_bits() selected out of uart_stop_bits_t

Hardware flow control mode

uart_set_hw_flow_ctrl() selected out of uart_hw_flowcontrol_t

Communication mode

uart_set_mode() selected out of uart_mode_t

Each of the above functions has a _get_ counterpart to check the currently set value. For example, to check the current baud rate value, call uart_get_baudrate().

Set Communication Pins

After setting communication parameters, configure the physical GPIO pins to which the other UART device will be connected. For this, call the function uart_set_pin() and specify the GPIO pin numbers to which the driver should route the TX, RX, RTS, and CTS signals. If you want to keep a currently allocated pin number for a specific signal, pass the macro UART_PIN_NO_CHANGE.

The same macro UART_PIN_NO_CHANGE should be specified for pins that will not be used.

// Set UART pins(TX: IO4, RX: IO5, RTS: IO18, CTS: IO19)
ESP_ERROR_CHECK(uart_set_pin(UART_NUM_1, 4, 5, 18, 19));

Install Drivers

Once the communication pins are set, install the driver by calling uart_driver_install() and specify the following parameters:

  • UART port number

  • Size of TX ring buffer

  • Size of RX ring buffer

  • Pointer to store the event queue handle

  • Event queue size

  • Flags to allocate an interrupt

The function allocates the required internal resources for the UART driver.

// Setup UART buffered IO with event queue
const int uart_buffer_size = (1024 * 2);
QueueHandle_t uart_queue;
// Install UART driver using an event queue here
ESP_ERROR_CHECK(uart_driver_install(UART_NUM_1, uart_buffer_size, \
                                        uart_buffer_size, 10, &uart_queue, 0));

Once this step is complete, you can connect the external UART device and check the communication.

Run UART Communication

Serial communication is controlled by each UART controller's finite state machine (FSM).

The process of sending data involves the following steps:

  1. Write data into TX FIFO buffer

  2. FSM serializes the data

  3. FSM sends the data out

The process of receiving data is similar, but the steps are reversed:

  1. FSM processes an incoming serial stream and parallelizes it

  2. FSM writes the data into RX FIFO buffer

  3. Read the data from RX FIFO buffer

Therefore, an application only writes and reads data from a specific buffer using uart_write_bytes() and uart_read_bytes() respectively, and the FSM does the rest.

Transmit Data

After preparing the data for transmission, call the function uart_write_bytes() and pass the data buffer's address and data length to it. The function copies the data to the TX ring buffer (either immediately or after enough space is available), and then exit. When there is free space in the TX FIFO buffer, an interrupt service routine (ISR) moves the data from the TX ring buffer to the TX FIFO buffer in the background. The code below demonstrates the use of this function.

// Write data to UART.
char* test_str = "This is a test string.\n";
uart_write_bytes(uart_num, (const char*)test_str, strlen(test_str));

The function uart_write_bytes_with_break() is similar to uart_write_bytes() but adds a serial break signal at the end of the transmission. A 'serial break signal' means holding the TX line low for a period longer than one data frame.

// Write data to UART, end with a break signal.
uart_write_bytes_with_break(uart_num, "test break\n",strlen("test break\n"), 100);

Another function for writing data to the TX FIFO buffer is uart_tx_chars(). Unlike uart_write_bytes(), this function does not block until space is available. Instead, it writes all data which can immediately fit into the hardware TX FIFO, and then return the number of bytes that were written.

There is a 'companion' function uart_wait_tx_done() that monitors the status of the TX FIFO buffer and returns once it is empty.

// Wait for packet to be sent
const uart_port_t uart_num = UART_NUM_1;
ESP_ERROR_CHECK(uart_wait_tx_done(uart_num, 100)); // wait timeout is 100 RTOS ticks (TickType_t)

Receive Data

Once the data is received by the UART and saved in the RX FIFO buffer, it needs to be retrieved using the function uart_read_bytes(). Before reading data, you can check the number of bytes available in the RX FIFO buffer by calling uart_get_buffered_data_len(). An example of using these functions is given below.

// Read data from UART.
const uart_port_t uart_num = UART_NUM_1;
uint8_t data[128];
int length = 0;
ESP_ERROR_CHECK(uart_get_buffered_data_len(uart_num, (size_t*)&length));
length = uart_read_bytes(uart_num, data, length, 100);

If the data in the RX FIFO buffer is no longer needed, you can clear the buffer by calling uart_flush().

Software Flow Control

If the hardware flow control is disabled, you can manually set the RTS and DTR signal levels by using the functions uart_set_rts() and uart_set_dtr() respectively.

Communication Mode Selection

The UART controller supports a number of communication modes. A mode can be selected using the function uart_set_mode(). Once a specific mode is selected, the UART driver handles the behavior of a connected UART device accordingly. As an example, it can control the RS485 driver chip using the RTS line to allow half-duplex RS485 communication.

// Setup UART in rs485 half duplex mode
ESP_ERROR_CHECK(uart_set_mode(uart_num, UART_MODE_RS485_HALF_DUPLEX));

Use Interrupts

There are many interrupts that can be generated depending on specific UART states or detected errors. The full list of available interrupts is provided in ESP32-P4 Technical Reference Manual > UART Controller (UART) > UART Interrupts and UHCI Interrupts [PDF]. You can enable or disable specific interrupts by calling uart_enable_intr_mask() or uart_disable_intr_mask() respectively.

The UART driver provides a convenient way to handle specific interrupts by wrapping them into corresponding events. Events defined in uart_event_type_t can be reported to a user application using the FreeRTOS queue functionality.

To receive the events that have happened, call uart_driver_install() and get the event queue handle returned from the function. Please see the above code snippet as an example.

The processed events include the following:

  • FIFO overflow (UART_FIFO_OVF): The RX FIFO can trigger an interrupt when it receives more data than the FIFO can store.

    • (Optional) Configure the full threshold of the FIFO space by entering it in the structure uart_intr_config_t and call uart_intr_config() to set the configuration. This can help the data stored in the RX FIFO can be processed timely in the driver to avoid FIFO overflow.

    • Enable the interrupts using the functions uart_enable_rx_intr().

    • Disable these interrupts using the corresponding functions uart_disable_rx_intr().

    const uart_port_t uart_num = UART_NUM_1;
    // Configure a UART interrupt threshold and timeout
    uart_intr_config_t uart_intr = {
        .intr_enable_mask = UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT,
        .rxfifo_full_thresh = 100,
        .rx_timeout_thresh = 10,
    };
    ESP_ERROR_CHECK(uart_intr_config(uart_num, &uart_intr));
    
    // Enable UART RX FIFO full threshold and timeout interrupts
    ESP_ERROR_CHECK(uart_enable_rx_intr(uart_num));
    
  • Pattern detection (UART_PATTERN_DET): An interrupt triggered on detecting a 'pattern' of the same character being received/sent repeatedly. It can be used, e.g., to detect a command string with a specific number of identical characters (the 'pattern') at the end. The following functions are available:

    //Set UART pattern detect function
    uart_enable_pattern_det_baud_intr(EX_UART_NUM, '+', PATTERN_CHR_NUM, 9, 0, 0);
    
  • Other events: The UART driver can report other events such as data receiving (UART_DATA), ring buffer full (UART_BUFFER_FULL), detecting NULL after the stop bit (UART_BREAK), parity check error (UART_PARITY_ERR), and frame error (UART_FRAME_ERR).

The strings inside of brackets indicate corresponding event names. An example of how to handle various UART events can be found in peripherals/uart/uart_events.

Deleting a Driver

If the communication established with uart_driver_install() is no longer required, the driver can be removed to free allocated resources by calling uart_driver_delete().

Macros

The API also defines several macros. For example, UART_HW_FIFO_LEN defines the length of hardware FIFO buffers; UART_BITRATE_MAX gives the maximum baud rate supported by the UART controllers, etc.

Use LP UART Controller with HP Core

The UART driver also supports to control the LP UART controller when the chip is in active mode. The configuration steps for the LP UART are the same as the steps for a normal UART controller, except:

  • The port number for the LP UART controller is defined by LP_UART_NUM_0.

  • The available clock sources for the LP UART controller can be found in lp_uart_sclk_t.

  • The size of the hardware FIFO for the LP UART controller is much smaller, which is defined in SOC_LP_UART_FIFO_LEN.

  • The GPIO pins for the LP UART controller can only be selected from the LP GPIO pins.

Overview of RS485 Specific Communication 0ptions

Note

The following section uses [UART_REGISTER_NAME].[UART_FIELD_BIT] to refer to UART register fields/bits. For more information on a specific option bit, see ESP32-P4 Technical Reference Manual > UART Controller (UART) > Register Summary [PDF]. Use the register name to navigate to the register description and then find the field/bit.

  • UART_RS485_CONF_REG.UART_RS485_EN: setting this bit enables RS485 communication mode support.

  • UART_RS485_CONF_REG.UART_RS485TX_RX_EN: if this bit is set, the transmitter's output signal loops back to the receiver's input signal.

  • UART_RS485_CONF_REG.UART_RS485RXBY_TX_EN: if this bit is set, the transmitter will still be sending data if the receiver is busy (remove collisions automatically by hardware).

The ESP32-P4's RS485 UART hardware can detect signal collisions during transmission of a datagram and generate the interrupt UART_RS485_CLASH_INT if this interrupt is enabled. The term collision means that a transmitted datagram is not equal to the one received on the other end. Data collisions are usually associated with the presence of other active devices on the bus or might occur due to bus errors.

The collision detection feature allows handling collisions when their interrupts are activated and triggered. The interrupts UART_RS485_FRM_ERR_INT and UART_RS485_PARITY_ERR_INT can be used with the collision detection feature to control frame errors and parity bit errors accordingly in RS485 mode. This functionality is supported in the UART driver and can be used by selecting the UART_MODE_RS485_APP_CTRL mode (see the function uart_set_mode()).

The collision detection feature can work with circuit A and circuit C (see Section Interface Connection Options). In the case of using circuit A or B, the RTS pin connected to the DE pin of the bus driver should be controlled by the user application. Use the function uart_get_collision_flag() to check if the collision detection flag has been raised.

The ESP32-P4 UART controllers themselves do not support half-duplex communication as they cannot provide automatic control of the RTS pin connected to the RE/DE input of RS485 bus driver. However, half-duplex communication can be achieved via software control of the RTS pin by the UART driver. This can be enabled by selecting the UART_MODE_RS485_HALF_DUPLEX mode when calling uart_set_mode().

Once the host starts writing data to the TX FIFO buffer, the UART driver automatically asserts the RTS pin (logic 1); once the last bit of the data has been transmitted, the driver de-asserts the RTS pin (logic 0). To use this mode, the software would have to disable the hardware flow control function. This mode works with all the used circuits shown below.

Interface Connection Options

This section provides example schematics to demonstrate the basic aspects of ESP32-P4's RS485 interface connection.

Note

  • The schematics below do not necessarily contain all required elements.

  • The analog devices ADM483 & ADM2483 are examples of common RS485 transceivers and can be replaced with other similar transceivers.

Circuit A: Collision Detection Circuit

        VCC ---------------+
                           |
                   +-------x-------+
        RXD <------| R             |
                   |              B|----------<> B
        TXD ------>| D    ADM483   |
ESP                |               |     RS485 bus side
        RTS ------>| DE            |
                   |              A|----------<> A
              +----| /RE           |
              |    +-------x-------+
              |            |
             GND          GND

This circuit is preferable because it allows for collision detection and is quite simple at the same time. The receiver in the line driver is constantly enabled, which allows the UART to monitor the RS485 bus. Echo suppression is performed by the UART peripheral when the bit UART_RS485_CONF_REG.UART_RS485TX_RX_EN is enabled.

Circuit B: Manual Switching Transmitter/Receiver Without Collision Detection

        VCC ---------------+
                           |
                   +-------x-------+
        RXD <------| R             |
                   |              B|-----------<> B
        TXD ------>| D    ADM483   |
ESP                |               |     RS485 bus side
        RTS --+--->| DE            |
              |    |              A|-----------<> A
              +----| /RE           |
                   +-------x-------+
                           |
                          GND

This circuit does not allow for collision detection. It suppresses the null bytes that the hardware receives when the bit UART_RS485_CONF_REG.UART_RS485TX_RX_EN is set. The bit UART_RS485_CONF_REG.UART_RS485RXBY_TX_EN is not applicable in this case.

Circuit C: Auto Switching Transmitter/Receiver

 VCC1 <-------------------+-----------+           +-------------------+----> VCC2
               10K ____   |           |           |                   |
              +---|____|--+       +---x-----------x---+    10K ____   |
              |                   |                   |   +---|____|--+
RX <----------+-------------------| RXD               |   |
                   10K ____       |                  A|---+---------------<> A (+)
              +-------|____|------| PV    ADM2483     |   |    ____  120
              |   ____            |                   |   +---|____|---+  RS485 bus side
      VCC1 <--+--|____|--+------->| DE                |                |
              10K        |        |                  B|---+------------+--<> B (-)
                      ---+    +-->| /RE               |   |    ____
         10K          |       |   |                   |   +---|____|---+
        ____       | /-C      +---| TXD               |    10K         |
TX >---|____|--+_B_|/   NPN   |   |                   |                |
                   |\         |   +---x-----------x---+                |
                   | \-E      |       |           |                    |
                      |       |       |           |                    |
                     GND1    GND1    GND1        GND2                 GND2

This galvanically isolated circuit does not require RTS pin control by a software application or driver because it controls the transceiver direction automatically. However, it requires suppressing null bytes during transmission by setting UART_RS485_CONF_REG.UART_RS485RXBY_TX_EN to 1 and UART_RS485_CONF_REG.UART_RS485TX_RX_EN to 0. This setup can work in any RS485 UART mode or even in UART_MODE_UART.

Application Examples

The table below describes the code examples available in the directory peripherals/uart/.

Code Example

Description

peripherals/uart/uart_echo

Configuring UART settings, installing the UART driver, and reading/writing over the UART1 interface.

peripherals/uart/uart_events

Reporting various communication events, using pattern detection interrupts.

peripherals/uart/uart_async_rxtxtasks

Transmitting and receiving data in two separate FreeRTOS tasks over the same UART.

peripherals/uart/uart_select

Using synchronous I/O multiplexing for UART file descriptors.

peripherals/uart/uart_echo_rs485

Setting up UART driver to communicate over RS485 interface in half-duplex mode. This example is similar to peripherals/uart/uart_echo but allows communication through an RS485 interface chip connected to ESP32-P4 pins.

peripherals/uart/nmea0183_parser

Obtaining GPS information by parsing NMEA0183 statements received from GPS via the UART peripheral.

API Reference

Header File

  • components/esp_driver_uart/include/driver/uart.h

  • This header file can be included with:

    #include "driver/uart.h"
    
  • This header file is a part of the API provided by the esp_driver_uart component. To declare that your component depends on esp_driver_uart, add the following to your CMakeLists.txt:

    REQUIRES esp_driver_uart
    

    or

    PRIV_REQUIRES esp_driver_uart
    

Functions

esp_err_t uart_driver_install(uart_port_t uart_num, int rx_buffer_size, int tx_buffer_size, int queue_size, QueueHandle_t *uart_queue, int intr_alloc_flags)

Install UART driver and set the UART to the default configuration.

UART ISR handler will be attached to the same CPU core that this function is running on.

Note

Rx_buffer_size should be greater than UART_HW_FIFO_LEN(uart_num). Tx_buffer_size should be either zero or greater than UART_HW_FIFO_LEN(uart_num).

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • rx_buffer_size -- UART RX ring buffer size.

  • tx_buffer_size -- UART TX ring buffer size. If set to zero, driver will not use TX buffer, TX function will block task until all data have been sent out.

  • queue_size -- UART event queue size/depth.

  • uart_queue -- UART event queue handle (out param). On success, a new queue handle is written here to provide access to UART events. If set to NULL, driver will not use an event queue.

  • intr_alloc_flags -- Flags used to allocate the interrupt. One or multiple (ORred) ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info. Do not set ESP_INTR_FLAG_IRAM here (the driver's ISR handler is not located in IRAM)

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_driver_delete(uart_port_t uart_num)

Uninstall UART driver.

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

bool uart_is_driver_installed(uart_port_t uart_num)

Checks whether the driver is installed or not.

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • true driver is installed

  • false driver is not installed

esp_err_t uart_set_word_length(uart_port_t uart_num, uart_word_length_t data_bit)

Set UART data bits.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • data_bit -- UART data bits

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_get_word_length(uart_port_t uart_num, uart_word_length_t *data_bit)

Get the UART data bit configuration.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • data_bit -- Pointer to accept value of UART data bits.

Returns

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*data_bit)

esp_err_t uart_set_stop_bits(uart_port_t uart_num, uart_stop_bits_t stop_bits)

Set UART stop bits.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • stop_bits -- UART stop bits

Returns

  • ESP_OK Success

  • ESP_FAIL Fail

esp_err_t uart_get_stop_bits(uart_port_t uart_num, uart_stop_bits_t *stop_bits)

Get the UART stop bit configuration.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • stop_bits -- Pointer to accept value of UART stop bits.

Returns

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*stop_bit)

esp_err_t uart_set_parity(uart_port_t uart_num, uart_parity_t parity_mode)

Set UART parity mode.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • parity_mode -- the enum of uart parity configuration

Returns

  • ESP_FAIL Parameter error

  • ESP_OK Success

esp_err_t uart_get_parity(uart_port_t uart_num, uart_parity_t *parity_mode)

Get the UART parity mode configuration.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • parity_mode -- Pointer to accept value of UART parity mode.

Returns

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*parity_mode)

esp_err_t uart_get_sclk_freq(uart_sclk_t sclk, uint32_t *out_freq_hz)

Get the frequency of a clock source for the HP UART port.

Parameters
  • sclk -- Clock source

  • out_freq_hz -- [out] Output of frequency, in Hz

Returns

  • ESP_ERR_INVALID_ARG: if the clock source is not supported

  • otherwise ESP_OK

esp_err_t uart_set_baudrate(uart_port_t uart_num, uint32_t baudrate)

Set UART baud rate.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • baudrate -- UART baud rate.

Returns

  • ESP_FAIL Parameter error

  • ESP_OK Success

esp_err_t uart_get_baudrate(uart_port_t uart_num, uint32_t *baudrate)

Get the UART baud rate configuration.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • baudrate -- Pointer to accept value of UART baud rate

Returns

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*baudrate)

esp_err_t uart_set_line_inverse(uart_port_t uart_num, uint32_t inverse_mask)

Set UART line inverse mode.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • inverse_mask -- Choose the wires that need to be inverted. Using the ORred mask of uart_signal_inv_t

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_set_hw_flow_ctrl(uart_port_t uart_num, uart_hw_flowcontrol_t flow_ctrl, uint8_t rx_thresh)

Set hardware flow control.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • flow_ctrl -- Hardware flow control mode

  • rx_thresh -- Threshold of Hardware RX flow control (0 ~ UART_HW_FIFO_LEN(uart_num)). Only when UART_HW_FLOWCTRL_RTS is set, will the rx_thresh value be set.

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_set_sw_flow_ctrl(uart_port_t uart_num, bool enable, uint8_t rx_thresh_xon, uint8_t rx_thresh_xoff)

Set software flow control.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1)

  • enable -- switch on or off

  • rx_thresh_xon -- low water mark

  • rx_thresh_xoff -- high water mark

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_get_hw_flow_ctrl(uart_port_t uart_num, uart_hw_flowcontrol_t *flow_ctrl)

Get the UART hardware flow control configuration.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • flow_ctrl -- Option for different flow control mode.

Returns

  • ESP_FAIL Parameter error

  • ESP_OK Success, result will be put in (*flow_ctrl)

esp_err_t uart_clear_intr_status(uart_port_t uart_num, uint32_t clr_mask)

Clear UART interrupt status.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • clr_mask -- Bit mask of the interrupt status to be cleared.

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_enable_intr_mask(uart_port_t uart_num, uint32_t enable_mask)

Set UART interrupt enable.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • enable_mask -- Bit mask of the enable bits.

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_disable_intr_mask(uart_port_t uart_num, uint32_t disable_mask)

Clear UART interrupt enable bits.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • disable_mask -- Bit mask of the disable bits.

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_enable_rx_intr(uart_port_t uart_num)

Enable UART RX interrupt (RX_FULL & RX_TIMEOUT INTERRUPT)

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_disable_rx_intr(uart_port_t uart_num)

Disable UART RX interrupt (RX_FULL & RX_TIMEOUT INTERRUPT)

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_disable_tx_intr(uart_port_t uart_num)

Disable UART TX interrupt (TX_FULL & TX_TIMEOUT INTERRUPT)

Parameters

uart_num -- UART port number

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_enable_tx_intr(uart_port_t uart_num, int enable, int thresh)

Enable UART TX interrupt (TX_FULL & TX_TIMEOUT INTERRUPT)

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • enable -- 1: enable; 0: disable

  • thresh -- Threshold of TX interrupt, 0 ~ UART_HW_FIFO_LEN(uart_num)

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_set_pin(uart_port_t uart_num, int tx_io_num, int rx_io_num, int rts_io_num, int cts_io_num)

Assign signals of a UART peripheral to GPIO pins.

Note

If the GPIO number configured for a UART signal matches one of the IOMUX signals for that GPIO, the signal will be connected directly via the IOMUX. Otherwise the GPIO and signal will be connected via the GPIO Matrix. For example, if on an ESP32 the call uart_set_pin(0, 1, 3, -1, -1) is performed, as GPIO1 is UART0's default TX pin and GPIO3 is UART0's default RX pin, both will be connected to respectively U0TXD and U0RXD through the IOMUX, totally bypassing the GPIO matrix. The check is performed on a per-pin basis. Thus, it is possible to have RX pin binded to a GPIO through the GPIO matrix, whereas TX is binded to its GPIO through the IOMUX.

Note

Internal signal can be output to multiple GPIO pads. Only one GPIO pad can connect with input signal.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • tx_io_num -- UART TX pin GPIO number.

  • rx_io_num -- UART RX pin GPIO number.

  • rts_io_num -- UART RTS pin GPIO number.

  • cts_io_num -- UART CTS pin GPIO number.

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_set_rts(uart_port_t uart_num, int level)

Manually set the UART RTS pin level.

Note

UART must be configured with hardware flow control disabled.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • level -- 1: RTS output low (active); 0: RTS output high (block)

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_set_dtr(uart_port_t uart_num, int level)

Manually set the UART DTR pin level.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • level -- 1: DTR output low; 0: DTR output high

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_set_tx_idle_num(uart_port_t uart_num, uint16_t idle_num)

Set UART idle interval after tx FIFO is empty.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • idle_num -- idle interval after tx FIFO is empty(unit: the time it takes to send one bit under current baudrate)

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_param_config(uart_port_t uart_num, const uart_config_t *uart_config)

Set UART configuration parameters.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • uart_config -- UART parameter settings

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_intr_config(uart_port_t uart_num, const uart_intr_config_t *intr_conf)

Configure UART interrupts.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • intr_conf -- UART interrupt settings

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_wait_tx_done(uart_port_t uart_num, TickType_t ticks_to_wait)

Wait until UART TX FIFO is empty.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • ticks_to_wait -- Timeout, count in RTOS ticks

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

  • ESP_ERR_TIMEOUT Timeout

int uart_tx_chars(uart_port_t uart_num, const char *buffer, uint32_t len)

Send data to the UART port from a given buffer and length.

This function will not wait for enough space in TX FIFO. It will just fill the available TX FIFO and return when the FIFO is full.

Note

This function should only be used when UART TX buffer is not enabled.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • buffer -- data buffer address

  • len -- data length to send

Returns

  • (-1) Parameter error

  • OTHERS (>=0) The number of bytes pushed to the TX FIFO

int uart_write_bytes(uart_port_t uart_num, const void *src, size_t size)

Send data to the UART port from a given buffer and length,.

If the UART driver's parameter 'tx_buffer_size' is set to zero: This function will not return until all the data have been sent out, or at least pushed into TX FIFO.

Otherwise, if the 'tx_buffer_size' > 0, this function will return after copying all the data to tx ring buffer, UART ISR will then move data from the ring buffer to TX FIFO gradually.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • src -- data buffer address

  • size -- data length to send

Returns

  • (-1) Parameter error

  • OTHERS (>=0) The number of bytes pushed to the TX FIFO

int uart_write_bytes_with_break(uart_port_t uart_num, const void *src, size_t size, int brk_len)

Send data to the UART port from a given buffer and length,.

If the UART driver's parameter 'tx_buffer_size' is set to zero: This function will not return until all the data and the break signal have been sent out. After all data is sent out, send a break signal.

Otherwise, if the 'tx_buffer_size' > 0, this function will return after copying all the data to tx ring buffer, UART ISR will then move data from the ring buffer to TX FIFO gradually. After all data sent out, send a break signal.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • src -- data buffer address

  • size -- data length to send

  • brk_len -- break signal duration(unit: the time it takes to send one bit at current baudrate)

Returns

  • (-1) Parameter error

  • OTHERS (>=0) The number of bytes pushed to the TX FIFO

int uart_read_bytes(uart_port_t uart_num, void *buf, uint32_t length, TickType_t ticks_to_wait)

UART read bytes from UART buffer.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • buf -- pointer to the buffer.

  • length -- data length

  • ticks_to_wait -- sTimeout, count in RTOS ticks

Returns

  • (-1) Error

  • OTHERS (>=0) The number of bytes read from UART buffer

esp_err_t uart_flush(uart_port_t uart_num)

Alias of uart_flush_input. UART ring buffer flush. This will discard all data in the UART RX buffer.

Note

Instead of waiting the data sent out, this function will clear UART rx buffer. In order to send all the data in tx FIFO, we can use uart_wait_tx_done function.

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_flush_input(uart_port_t uart_num)

Clear input buffer, discard all the data is in the ring-buffer.

Note

In order to send all the data in tx FIFO, we can use uart_wait_tx_done function.

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_get_buffered_data_len(uart_port_t uart_num, size_t *size)

UART get RX ring buffer cached data length.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • size -- Pointer of size_t to accept cached data length

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_get_tx_buffer_free_size(uart_port_t uart_num, size_t *size)

UART get TX ring buffer free space size.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • size -- Pointer of size_t to accept the free space size

Returns

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

esp_err_t uart_disable_pattern_det_intr(uart_port_t uart_num)

UART disable pattern detect function. Designed for applications like 'AT commands'. When the hardware detects a series of one same character, the interrupt will be triggered.

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

esp_err_t uart_enable_pattern_det_baud_intr(uart_port_t uart_num, char pattern_chr, uint8_t chr_num, int chr_tout, int post_idle, int pre_idle)

UART enable pattern detect function. Designed for applications like 'AT commands'. When the hardware detect a series of one same character, the interrupt will be triggered.

Parameters
  • uart_num -- UART port number.

  • pattern_chr -- character of the pattern.

  • chr_num -- number of the character, 8bit value.

  • chr_tout -- timeout of the interval between each pattern characters, 16bit value, unit is the baud-rate cycle you configured. When the duration is more than this value, it will not take this data as at_cmd char.

  • post_idle -- idle time after the last pattern character, 16bit value, unit is the baud-rate cycle you configured. When the duration is less than this value, it will not take the previous data as the last at_cmd char

  • pre_idle -- idle time before the first pattern character, 16bit value, unit is the baud-rate cycle you configured. When the duration is less than this value, it will not take this data as the first at_cmd char.

Returns

  • ESP_OK Success

  • ESP_FAIL Parameter error

int uart_pattern_pop_pos(uart_port_t uart_num)

Return the nearest detected pattern position in buffer. The positions of the detected pattern are saved in a queue, this function will dequeue the first pattern position and move the pointer to next pattern position.

The following APIs will modify the pattern position info: uart_flush_input, uart_read_bytes, uart_driver_delete, uart_pop_pattern_pos It is the application's responsibility to ensure atomic access to the pattern queue and the rx data buffer when using pattern detect feature.

Note

If the RX buffer is full and flow control is not enabled, the detected pattern may not be found in the rx buffer due to overflow.

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • (-1) No pattern found for current index or parameter error

  • others the pattern position in rx buffer.

int uart_pattern_get_pos(uart_port_t uart_num)

Return the nearest detected pattern position in buffer. The positions of the detected pattern are saved in a queue, This function do nothing to the queue.

The following APIs will modify the pattern position info: uart_flush_input, uart_read_bytes, uart_driver_delete, uart_pop_pattern_pos It is the application's responsibility to ensure atomic access to the pattern queue and the rx data buffer when using pattern detect feature.

Note

If the RX buffer is full and flow control is not enabled, the detected pattern may not be found in the rx buffer due to overflow.

Parameters

uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

Returns

  • (-1) No pattern found for current index or parameter error

  • others the pattern position in rx buffer.

esp_err_t uart_pattern_queue_reset(uart_port_t uart_num, int queue_length)

Allocate a new memory with the given length to save record the detected pattern position in rx buffer.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1).

  • queue_length -- Max queue length for the detected pattern. If the queue length is not large enough, some pattern positions might be lost. Set this value to the maximum number of patterns that could be saved in data buffer at the same time.

Returns

  • ESP_ERR_NO_MEM No enough memory

  • ESP_ERR_INVALID_STATE Driver not installed

  • ESP_FAIL Parameter error

  • ESP_OK Success

esp_err_t uart_set_mode(uart_port_t uart_num, uart_mode_t mode)

UART set communication mode.

Note

This function must be executed after uart_driver_install(), when the driver object is initialized.

Parameters
  • uart_num -- Uart number to configure, the max port number is (UART_NUM_MAX -1).

  • mode -- UART UART mode to set

Returns

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

esp_err_t uart_set_rx_full_threshold(uart_port_t uart_num, int threshold)

Set uart threshold value for RX fifo full.

Note

If application is using higher baudrate and it is observed that bytes in hardware RX fifo are overwritten then this threshold can be reduced

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1)

  • threshold -- Threshold value above which RX fifo full interrupt is generated

Returns

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_ERR_INVALID_STATE Driver is not installed

esp_err_t uart_set_tx_empty_threshold(uart_port_t uart_num, int threshold)

Set uart threshold values for TX fifo empty.

Parameters
  • uart_num -- UART port number, the max port number is (UART_NUM_MAX -1)

  • threshold -- Threshold value below which TX fifo empty interrupt is generated

Returns

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_ERR_INVALID_STATE Driver is not installed

esp_err_t uart_set_rx_timeout(uart_port_t uart_num, const uint8_t tout_thresh)

UART set threshold timeout for TOUT feature.

Parameters
  • uart_num -- Uart number to configure, the max port number is (UART_NUM_MAX -1).

  • tout_thresh -- This parameter defines timeout threshold in uart symbol periods. The maximum value of threshold is 126. tout_thresh = 1, defines TOUT interrupt timeout equal to transmission time of one symbol (~11 bit) on current baudrate. If the time is expired the UART_RXFIFO_TOUT_INT interrupt is triggered. If tout_thresh == 0, the TOUT feature is disabled.

Returns

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_ERR_INVALID_STATE Driver is not installed

esp_err_t uart_get_collision_flag(uart_port_t uart_num, bool *collision_flag)

Returns collision detection flag for RS485 mode Function returns the collision detection flag into variable pointed by collision_flag. *collision_flag = true, if collision detected else it is equal to false. This function should be executed when actual transmission is completed (after uart_write_bytes()).

Parameters
  • uart_num -- Uart number to configure the max port number is (UART_NUM_MAX -1).

  • collision_flag -- Pointer to variable of type bool to return collision flag.

Returns

  • ESP_OK Success

  • ESP_ERR_INVALID_ARG Parameter error

esp_err_t uart_set_wakeup_threshold(uart_port_t uart_num, int wakeup_threshold)

Set the number of RX pin signal edges for light sleep wakeup.

UART can be used to wake up the system from light sleep. This feature works by counting the number of positive edges on RX pin and comparing the count to the threshold. When the count exceeds the threshold, system is woken up from light sleep. This function allows setting the threshold value.

Stop bit and parity bits (if enabled) also contribute to the number of edges. For example, letter 'a' with ASCII code 97 is encoded as 0100001101 on the wire (with 8n1 configuration), start and stop bits included. This sequence has 3 positive edges (transitions from 0 to 1). Therefore, to wake up the system when 'a' is sent, set wakeup_threshold=3.

The character that triggers wakeup is not received by UART (i.e. it can not be obtained from UART FIFO). Depending on the baud rate, a few characters after that will also not be received. Note that when the chip enters and exits light sleep mode, APB frequency will be changing. To ensure that UART has correct Baud rate all the time, it is necessary to select a source clock which has a fixed frequency and remains active during sleep. For the supported clock sources of the chips, please refer to uart_sclk_t or soc_periph_uart_clk_src_legacy_t

Note

in ESP32, the wakeup signal can only be input via IO_MUX (i.e. GPIO3 should be configured as function_1 to wake up UART0, GPIO9 should be configured as function_5 to wake up UART1), UART2 does not support light sleep wakeup feature.

Parameters
  • uart_num -- UART number, the max port number is (UART_NUM_MAX -1).

  • wakeup_threshold -- number of RX edges for light sleep wakeup, value is 3 .. 0x3ff.

Returns

  • ESP_OK on success

  • ESP_ERR_INVALID_ARG if uart_num is incorrect or wakeup_threshold is outside of [3, 0x3ff] range.

esp_err_t uart_get_wakeup_threshold(uart_port_t uart_num, int *out_wakeup_threshold)

Get the number of RX pin signal edges for light sleep wakeup.

See description of uart_set_wakeup_threshold for the explanation of UART wakeup feature.

Parameters
  • uart_num -- UART number, the max port number is (UART_NUM_MAX -1).

  • out_wakeup_threshold -- [out] output, set to the current value of wakeup threshold for the given UART.

Returns

  • ESP_OK on success

  • ESP_ERR_INVALID_ARG if out_wakeup_threshold is NULL

esp_err_t uart_wait_tx_idle_polling(uart_port_t uart_num)

Wait until UART tx memory empty and the last char send ok (polling mode).

Returns

  • ESP_OK on success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_FAIL Driver not installed

Parameters

uart_num -- UART number

esp_err_t uart_set_loop_back(uart_port_t uart_num, bool loop_back_en)

Configure TX signal loop back to RX module, just for the test usage.

Returns

  • ESP_OK on success

  • ESP_ERR_INVALID_ARG Parameter error

  • ESP_FAIL Driver not installed

Parameters
  • uart_num -- UART number

  • loop_back_en -- Set true to enable the loop back function, else set it false.

void uart_set_always_rx_timeout(uart_port_t uart_num, bool always_rx_timeout_en)

Configure behavior of UART RX timeout interrupt.

When always_rx_timeout is true, timeout interrupt is triggered even if FIFO is full. This function can cause extra timeout interrupts triggered only to send the timeout event. Call this function only if you want to ensure timeout interrupt will always happen after a byte stream.

Parameters
  • uart_num -- UART number

  • always_rx_timeout_en -- Set to false enable the default behavior of timeout interrupt, set it to true to always trigger timeout interrupt.

Structures

struct uart_config_t

UART configuration parameters for uart_param_config function.

Public Members

int baud_rate

UART baud rate

uart_word_length_t data_bits

UART byte size

uart_parity_t parity

UART parity mode

uart_stop_bits_t stop_bits

UART stop bits

uart_hw_flowcontrol_t flow_ctrl

UART HW flow control mode (cts/rts)

uint8_t rx_flow_ctrl_thresh

UART HW RTS threshold

uart_sclk_t source_clk

UART source clock selection

lp_uart_sclk_t lp_source_clk

LP_UART source clock selection

uint32_t backup_before_sleep

If set, the driver will backup/restore the HP UART registers before entering/after exiting sleep mode. By this approach, the system can power off HP UART's power domain. This can save power, but at the expense of more RAM being consumed

struct uart_config_t::[anonymous] flags

Configuration flags

struct uart_intr_config_t

UART interrupt configuration parameters for uart_intr_config function.

Public Members

uint32_t intr_enable_mask

UART interrupt enable mask, choose from UART_XXXX_INT_ENA_M under UART_INT_ENA_REG(i), connect with bit-or operator

uint8_t rx_timeout_thresh

UART timeout interrupt threshold (unit: time of sending one byte)

uint8_t txfifo_empty_intr_thresh

UART TX empty interrupt threshold.

uint8_t rxfifo_full_thresh

UART RX full interrupt threshold.

struct uart_event_t

Event structure used in UART event queue.

Public Members

uart_event_type_t type

UART event type

size_t size

UART data size for UART_DATA event

bool timeout_flag

UART data read timeout flag for UART_DATA event (no new data received during configured RX TOUT) If the event is caused by FIFO-full interrupt, then there will be no event with the timeout flag before the next byte coming.

Macros

UART_PIN_NO_CHANGE
UART_FIFO_LEN

Length of the HP UART HW FIFO.

UART_HW_FIFO_LEN(uart_num)

Length of the UART HW FIFO.

UART_BITRATE_MAX

Maximum configurable bitrate.

Type Definitions

typedef intr_handle_t uart_isr_handle_t

Enumerations

enum uart_event_type_t

UART event types used in the ring buffer.

Values:

enumerator UART_DATA

UART data event

enumerator UART_BREAK

UART break event

enumerator UART_BUFFER_FULL

UART RX buffer full event

enumerator UART_FIFO_OVF

UART FIFO overflow event

enumerator UART_FRAME_ERR

UART RX frame error event

enumerator UART_PARITY_ERR

UART RX parity event

enumerator UART_DATA_BREAK

UART TX data and break event

enumerator UART_PATTERN_DET

UART pattern detected

enumerator UART_WAKEUP

UART wakeup event

enumerator UART_EVENT_MAX

UART event max index

Header File

Structures

struct uart_at_cmd_t

UART AT cmd char configuration parameters Note that this function may different on different chip. Please refer to the TRM at confirguration.

Public Members

uint8_t cmd_char

UART AT cmd char

uint8_t char_num

AT cmd char repeat number

uint32_t gap_tout

gap time(in baud-rate) between AT cmd char

uint32_t pre_idle

the idle time(in baud-rate) between the non AT char and first AT char

uint32_t post_idle

the idle time(in baud-rate) between the last AT char and the none AT char

struct uart_sw_flowctrl_t

UART software flow control configuration parameters.

Public Members

uint8_t xon_char

Xon flow control char

uint8_t xoff_char

Xoff flow control char

uint8_t xon_thrd

If the software flow control is enabled and the data amount in rxfifo is less than xon_thrd, an xon_char will be sent

uint8_t xoff_thrd

If the software flow control is enabled and the data amount in rxfifo is more than xoff_thrd, an xoff_char will be sent

Type Definitions

typedef soc_periph_uart_clk_src_legacy_t uart_sclk_t

UART source clock.

typedef soc_periph_lp_uart_clk_src_t lp_uart_sclk_t

LP_UART source clock.

Enumerations

enum uart_port_t

UART port number, can be UART_NUM_0 ~ (UART_NUM_MAX -1).

Values:

enumerator UART_NUM_0

UART port 0

enumerator UART_NUM_1

UART port 1

enumerator UART_NUM_2

UART port 2

enumerator UART_NUM_3

UART port 3

enumerator UART_NUM_4

UART port 4

enumerator LP_UART_NUM_0

LP UART port 0

enumerator UART_NUM_MAX

UART port max

enum uart_mode_t

UART mode selection.

Values:

enumerator UART_MODE_UART

mode: regular UART mode

enumerator UART_MODE_RS485_HALF_DUPLEX

mode: half duplex RS485 UART mode control by RTS pin

enumerator UART_MODE_IRDA

mode: IRDA UART mode

enumerator UART_MODE_RS485_COLLISION_DETECT

mode: RS485 collision detection UART mode (used for test purposes)

enumerator UART_MODE_RS485_APP_CTRL

mode: application control RS485 UART mode (used for test purposes)

enum uart_word_length_t

UART word length constants.

Values:

enumerator UART_DATA_5_BITS

word length: 5bits

enumerator UART_DATA_6_BITS

word length: 6bits

enumerator UART_DATA_7_BITS

word length: 7bits

enumerator UART_DATA_8_BITS

word length: 8bits

enumerator UART_DATA_BITS_MAX
enum uart_stop_bits_t

UART stop bits number.

Values:

enumerator UART_STOP_BITS_1

stop bit: 1bit

enumerator UART_STOP_BITS_1_5

stop bit: 1.5bits

enumerator UART_STOP_BITS_2

stop bit: 2bits

enumerator UART_STOP_BITS_MAX
enum uart_parity_t

UART parity constants.

Values:

enumerator UART_PARITY_DISABLE

Disable UART parity

enumerator UART_PARITY_EVEN

Enable UART even parity

enumerator UART_PARITY_ODD

Enable UART odd parity

enum uart_hw_flowcontrol_t

UART hardware flow control modes.

Values:

enumerator UART_HW_FLOWCTRL_DISABLE

disable hardware flow control

enumerator UART_HW_FLOWCTRL_RTS

enable RX hardware flow control (rts)

enumerator UART_HW_FLOWCTRL_CTS

enable TX hardware flow control (cts)

enumerator UART_HW_FLOWCTRL_CTS_RTS

enable hardware flow control

enumerator UART_HW_FLOWCTRL_MAX
enum uart_signal_inv_t

UART signal bit map.

Values:

enumerator UART_SIGNAL_INV_DISABLE

Disable UART signal inverse

enumerator UART_SIGNAL_IRDA_TX_INV

inverse the UART irda_tx signal

enumerator UART_SIGNAL_IRDA_RX_INV

inverse the UART irda_rx signal

enumerator UART_SIGNAL_RXD_INV

inverse the UART rxd signal

enumerator UART_SIGNAL_CTS_INV

inverse the UART cts signal

enumerator UART_SIGNAL_DSR_INV

inverse the UART dsr signal

enumerator UART_SIGNAL_TXD_INV

inverse the UART txd signal

enumerator UART_SIGNAL_RTS_INV

inverse the UART rts signal

enumerator UART_SIGNAL_DTR_INV

inverse the UART dtr signal

GPIO Lookup Macros

The UART peripherals have dedicated IO_MUX pins to which they are connected directly. However, signals can also be routed to other pins using the less direct GPIO matrix. To use direct routes, you need to know which pin is a dedicated IO_MUX pin for a UART channel. GPIO Lookup Macros simplify the process of finding and assigning IO_MUX pins. You choose a macro based on either the IO_MUX pin number, or a required UART channel name, and the macro returns the matching counterpart for you. See some examples below.

Note

These macros are useful if you need very high UART baud rates (over 40 MHz), which means you will have to use IO_MUX pins only. In other cases, these macros can be ignored, and you can use the GPIO Matrix as it allows you to configure any GPIO pin for any UART function.

  1. UART_NUM_2_TXD_DIRECT_GPIO_NUM returns the IO_MUX pin number of UART channel 2 TXD pin (pin 17)

  2. UART_GPIO19_DIRECT_CHANNEL returns the UART number of GPIO 19 when connected to the UART peripheral via IO_MUX (this is UART_NUM_0)

  3. UART_CTS_GPIO19_DIRECT_CHANNEL returns the UART number of GPIO 19 when used as the UART CTS pin via IO_MUX (this is UART_NUM_0). It is similar to the above macro but specifies the pin function which is also part of the IO_MUX assignment.

Header File

Macros

UART_GPIO37_DIRECT_CHANNEL
UART_NUM_0_TXD_DIRECT_GPIO_NUM
UART_GPIO38_DIRECT_CHANNEL
UART_NUM_0_RXD_DIRECT_GPIO_NUM
UART_GPIO8_DIRECT_CHANNEL
UART_NUM_0_RTS_DIRECT_GPIO_NUM
UART_GPIO9_DIRECT_CHANNEL
UART_NUM_0_CTS_DIRECT_GPIO_NUM
UART_TXD_GPIO37_DIRECT_CHANNEL
UART_RXD_GPIO38_DIRECT_CHANNEL
UART_RTS_GPIO8_DIRECT_CHANNEL
UART_CTS_GPIO9_DIRECT_CHANNEL
UART_GPIO10_DIRECT_CHANNEL
UART_NUM_1_TXD_DIRECT_GPIO_NUM
UART_GPIO11_DIRECT_CHANNEL
UART_NUM_1_RXD_DIRECT_GPIO_NUM
UART_GPIO12_DIRECT_CHANNEL
UART_NUM_1_RTS_DIRECT_GPIO_NUM
UART_GPIO13_DIRECT_CHANNEL
UART_NUM_1_CTS_DIRECT_GPIO_NUM
UART_TXD_GPIO10_DIRECT_CHANNEL
UART_RXD_GPIO11_DIRECT_CHANNEL
UART_RTS_GPIO12_DIRECT_CHANNEL
UART_CTS_GPIO13_DIRECT_CHANNEL