Support for External RAM
Introduction
ESP32-S3 has a few hundred kilobytes of internal RAM, residing on the same die as the rest of the chip components. It can be insufficient for some purposes, so ESP32-S3 has the ability to use up to 32 MB of virtual addresses for external PSRAM (Psuedostatic RAM) memory. The external memory is incorporated in the memory map and, with certain restrictions, is usable in the same way as internal data RAM.
The 32 MB virtual addresses are shared with flash instructions and rodata.
Hardware
ESP32-S3 supports PSRAM connected in parallel with the SPI flash chip. While ESP32-S3 is capable of supporting several types of RAM chips, ESP-IDF currently only supports Espressif branded PSRAM chips (e.g., ESP-PSRAM32, ESP-PSRAM64, etc).
Note
Some PSRAM chips are 1.8 V devices and some are 3.3 V. The working voltage of the PSRAM chip must match the working voltage of the flash component. Consult the datasheet for your PSRAM chip and ESP32-S3 device to find out the working voltages. For a 1.8 V PSRAM chip, make sure to either set the MTDI pin to a high signal level on bootup, or program ESP32-S3 eFuses to always use the VDD_SIO level of 1.8 V. Not doing this can damage the PSRAM and/or flash chip.
Note
Espressif produces both modules and system-in-package chips that integrate compatible PSRAM and flash and are ready to mount on a product PCB. Consult the Espressif website for more information. If you are using a custom PSRAM chip, ESP-IDF SDK might not be compatible with it.
For specific details about connecting the SoC or module pins to an external PSRAM chip, consult the SoC or module datasheet.
Configuring External RAM
ESP-IDF fully supports the use of external RAM in applications. Once the external RAM is initialized at startup, ESP-IDF can be configured to integrate the external RAM in several ways:
Provide External RAM via malloc() (default)
Integrate RAM into the ESP32-S3 Memory Map
Select this option by choosing Integrate RAM into memory map from CONFIG_SPIRAM_USE.
This is the most basic option for external RAM integration. Most likely, you will need another, more advanced option.
During the ESP-IDF startup, external RAM is mapped into the data virtual address space. The address space is dynamically allocated. The length will be the mininum length between the PSRAM size and the available data virtual address space size.
Applications can manually place data in external memory by creating pointers to this region. So if an application uses external memory, it is responsible for all management of the external RAM: coordinating buffer usage, preventing corruption, etc.
It is recommended to access the PSRAM by ESP-IDF heap memory allocator (see next chapter).
Add External RAM to the Capability Allocator
Select this option by choosing Make RAM allocatable using heap_caps_malloc(..., MALLOC_CAP_SPIRAM) from CONFIG_SPIRAM_USE.
When enabled, memory is mapped to data virtual address space and also added to the capabilities-based heap memory allocator using MALLOC_CAP_SPIRAM.
To allocate memory from external RAM, a program should call heap_caps_malloc(size, MALLOC_CAP_SPIRAM). After use, this memory can be freed by calling the normal free() function.
Provide External RAM via malloc()
Select this option by choosing Make RAM allocatable using malloc() as well from CONFIG_SPIRAM_USE. This is the default option.
In this case, memory is added to the capability allocator as described for the previous option. However, it is also added to the pool of RAM that can be returned by the standard malloc() function.
This allows any application to use the external RAM without having to rewrite the code to use heap_caps_malloc(..., MALLOC_CAP_SPIRAM).
An additional configuration item, CONFIG_SPIRAM_MALLOC_ALWAYSINTERNAL, can be used to set the size threshold when a single allocation should prefer external memory:
When allocating a size less than the threshold, the allocator will try internal memory first.
When allocating a size equal to or larger than the threshold, the allocator will try external memory first.
If a suitable block of preferred internal/external memory is not available, the allocator will try the other type of memory.
Because some buffers can only be allocated in internal memory, a second configuration item CONFIG_SPIRAM_MALLOC_RESERVE_INTERNAL defines a pool of internal memory which is reserved for only explicitly internal allocations (such as memory for DMA use). Regular malloc() will not allocate from this pool. The MALLOC_CAP_DMA and MALLOC_CAP_INTERNAL flags can be used to allocate memory from this pool.
Allow .bss Segment to Be Placed in External Memory
Enable this option by checking CONFIG_SPIRAM_ALLOW_BSS_SEG_EXTERNAL_MEMORY.
If enabled, the region of the data virtual address space where the PSRAM is mapped to will be used to store zero-initialized data (BSS segment) from the lwIP, net80211, libpp, and bluedroid ESP-IDF libraries.
Additional data can be moved from the internal BSS segment to external RAM by applying the macro EXT_RAM_BSS_ATTR to any static declaration (which is not initialized to a non-zero value).
It is also possible to place the BSS section of a component or a library to external RAM using linker fragment scheme extram_bss.
This option reduces the internal static memory used by the BSS segment.
Remaining external RAM can also be added to the capability heap allocator using the method shown above.
Move Instructions in Flash to PSRAM
The CONFIG_SPIRAM_FETCH_INSTRUCTIONS option allows the flash .text sections (use for instructions) to be placed in PSRAM.
By enabling the CONFIG_SPIRAM_FETCH_INSTRUCTIONS option
Instructions from the
.textsections of flash are moved into PSRAM on system startup.The corresponding virtual memory range of those instructions will also be re-mapped to PSRAM.
If CONFIG_SPIRAM_RODATA is also enabled, the cache will not be disabled during an SPI1 flash operation. You do not need to make sure ISRs, ISR callbacks and involved data are placed in internal RAM, thus internal RAM usage can be optimized.
Move Read-Only Data in Flash to PSRAM
The CONFIG_SPIRAM_RODATA option allows the flash .rodata sections (use for read only data) to be placed in PSRAM.
By enabling the CONFIG_SPIRAM_RODATA option
Instructions from the
.rodatasections of flash are moved into PSRAM on system startup.The corresponding virtual memory range of those rodata will also be re-mapped to PSRAM.
If CONFIG_SPIRAM_FETCH_INSTRUCTIONS is also enabled, the cache will not be disabled during an SPI1 flash operation. You do not need to make sure ISRs, ISR callbacks and involved data are placed in internal RAM, thus internal RAM usage can be optimized.
Restrictions
External RAM use has the following restrictions:
When flash cache is disabled (for example, if the flash is being written to), the external RAM also becomes inaccessible. Any read operations from or write operations to it will lead to an illegal cache access exception. This is also the reason why ESP-IDF does not by default allocate any task stacks in external RAM (see below).
Although ESP32-S3 has hardware support for DMA to or from external RAM, there are still limitations:
DMA transaction descriptors cannot be placed in PSRAM.
The bandwidth that DMA accesses external RAM is very limited, especially when the core is trying to access the external RAM at the same time.
You can configure CONFIG_SPIRAM_SPEED as 120 MHz for an octal PSRAM. The bandwidth will be improved. However there are still restrictions for this option. See All Supported PSRAM Modes and Speeds for more details.
External RAM uses the same cache region as the external flash. This means that frequently accessed variables in external RAM can be read and modified almost as quickly as in internal RAM. However, when accessing large chunks of data (> 32 KB), the cache can be insufficient, and speeds will fall back to the access speed of the external RAM. Moreover, accessing large chunks of data can "push out" cached flash, possibly making the execution of code slower afterwards.
In general, external RAM will not be used as task stack memory.
xTaskCreate()and similar functions will always allocate internal memory for stack and task TCBs.
The option CONFIG_SPIRAM_ALLOW_STACK_EXTERNAL_MEMORY can be used to allow placing task stacks into external memory. In these cases xTaskCreateStatic() must be used to specify a task stack buffer allocated from external memory, otherwise task stacks will still be allocated from internal memory.
Failure to Initialize
By default, failure to initialize external RAM will cause the ESP-IDF startup to abort. This can be disabled by enabling the config item CONFIG_SPIRAM_IGNORE_NOTFOUND.
Encryption
It is possible to enable automatic encryption for data stored in external RAM. When this is enabled any data read and written through the cache will automatically be encrypted or decrypted by the external memory encryption hardware.
This feature is enabled whenever flash encryption is enabled. For more information on how to enable and how it works see Flash Encryption.