I80 接口的 LCD

[English]

  1. 调用 esp_lcd_new_i80_bus() 创建 I80 总线。请为英特尔 8080 并行总线设置以下参数:

    esp_lcd_i80_bus_handle_t i80_bus = NULL;
    esp_lcd_i80_bus_config_t bus_config = {
        .clk_src = LCD_CLK_SRC_DEFAULT,
        .dc_gpio_num = EXAMPLE_PIN_NUM_DC,
        .wr_gpio_num = EXAMPLE_PIN_NUM_PCLK,
        .data_gpio_nums = {
            EXAMPLE_PIN_NUM_DATA0,
            EXAMPLE_PIN_NUM_DATA1,
            EXAMPLE_PIN_NUM_DATA2,
            EXAMPLE_PIN_NUM_DATA3,
            EXAMPLE_PIN_NUM_DATA4,
            EXAMPLE_PIN_NUM_DATA5,
            EXAMPLE_PIN_NUM_DATA6,
            EXAMPLE_PIN_NUM_DATA7,
        },
        .bus_width = 8,
        .max_transfer_bytes = EXAMPLE_LCD_H_RES * 100 * sizeof(uint16_t), // 单次最多可传输 100 行像素(假设像素格式为 RGB565)
        .dma_burst_size = EXAMPLE_DMA_BURST_SIZE,
    };
    ESP_ERROR_CHECK(esp_lcd_new_i80_bus(&bus_config, &i80_bus));
    
  2. 从 I80 总线分配一个 LCD IO 设备句柄。在此步骤中,需要提供以下信息:

    esp_lcd_panel_io_handle_t io_handle = NULL;
    esp_lcd_panel_io_i80_config_t io_config = {
        .cs_gpio_num = EXAMPLE_PIN_NUM_CS,
        .pclk_hz = EXAMPLE_LCD_PIXEL_CLOCK_HZ,
        .trans_queue_depth = 10,
        .dc_levels = {
            .dc_idle_level = 0,
            .dc_cmd_level = 0,
            .dc_dummy_level = 0,
            .dc_data_level = 1,
        },
        .lcd_cmd_bits = EXAMPLE_LCD_CMD_BITS,
        .lcd_param_bits = EXAMPLE_LCD_PARAM_BITS,
    };
    ESP_ERROR_CHECK(esp_lcd_new_panel_io_i80(i80_bus, &io_config, &io_handle));
    
  3. 安装 LCD 控制器驱动程序。LCD 控制器驱动程序负责向 LCD 控制器芯片发送命令和参数。在此步骤中,需要指定上一步骤中分配到的 I80 IO 设备句柄以及一些面板特定配置:

    • esp_lcd_panel_dev_config_t::bits_per_pixel 设置像素颜色数据的位宽。LCD 驱动程序使用此值计算要发送到 LCD 控制器芯片的字节数。

    • esp_lcd_panel_dev_config_t::reset_gpio_num 设置复位管脚的 GPIO 编号。如果 LCD 控制器芯片没有复位管脚,可将此值设置为 -1

    • esp_lcd_panel_dev_config_t::rgb_ele_order 设置像素颜色数据的颜色顺序。

    esp_lcd_panel_dev_config_t panel_config = {
        .reset_gpio_num = EXAMPLE_PIN_NUM_RST,
        .rgb_ele_order = LCD_RGB_ELEMENT_ORDER_RGB,
        .bits_per_pixel = 16,
    };
    ESP_ERROR_CHECK(esp_lcd_new_panel_st7789(io_handle, &panel_config, &panel_handle));
    

API 参考

Header File

  • components/esp_lcd/include/esp_lcd_io_i80.h

  • This header file can be included with:

    #include "esp_lcd_io_i80.h"
    
  • This header file is a part of the API provided by the esp_lcd component. To declare that your component depends on esp_lcd, add the following to your CMakeLists.txt:

    REQUIRES esp_lcd
    

    or

    PRIV_REQUIRES esp_lcd
    

Functions

esp_err_t esp_lcd_new_i80_bus(const esp_lcd_i80_bus_config_t *bus_config, esp_lcd_i80_bus_handle_t *ret_bus)

Create Intel 8080 bus handle.

参数
  • bus_config -- [in] Bus configuration

  • ret_bus -- [out] Returned bus handle

返回

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_NO_MEM if out of memory

  • ESP_ERR_NOT_FOUND if no free bus is available

  • ESP_OK on success

esp_err_t esp_lcd_del_i80_bus(esp_lcd_i80_bus_handle_t bus)

Destroy Intel 8080 bus handle.

参数

bus -- [in] Intel 8080 bus handle, created by esp_lcd_new_i80_bus()

返回

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_INVALID_STATE if there still be some device attached to the bus

  • ESP_OK on success

esp_err_t esp_lcd_new_panel_io_i80(esp_lcd_i80_bus_handle_t bus, const esp_lcd_panel_io_i80_config_t *io_config, esp_lcd_panel_io_handle_t *ret_io)

Create LCD panel IO, for Intel 8080 interface.

参数
  • bus -- [in] Intel 8080 bus handle, created by esp_lcd_new_i80_bus()

  • io_config -- [in] IO configuration, for i80 interface

  • ret_io -- [out] Returned panel IO handle

返回

  • ESP_ERR_INVALID_ARG if parameter is invalid

  • ESP_ERR_NOT_SUPPORTED if some configuration can't be satisfied, e.g. pixel clock out of the range

  • ESP_ERR_NO_MEM if out of memory

  • ESP_OK on success

void *esp_lcd_i80_alloc_draw_buffer(esp_lcd_panel_io_handle_t io, size_t size, uint32_t caps)

Allocate a draw buffer that can be used by I80 interfaced LCD panel.

备注

This function differs from the normal 'heap_caps_*' functions in that it can also automatically handle the alignment required by DMA burst, cache line size, etc.

参数
  • io -- [in] Panel IO handle, created by esp_lcd_new_panel_io_i80()

  • size -- [in] Size of memory to be allocated

  • caps -- [in] Bitwise OR of MALLOC_CAP_* flags indicating the type of memory desired for the allocation

返回

Pointer to a new buffer of size 'size' with capabilities 'caps', or NULL if allocation failed

Structures

struct esp_lcd_i80_bus_config_t

LCD Intel 8080 bus configuration structure.

Public Members

int dc_gpio_num

GPIO used for D/C line

int wr_gpio_num

GPIO used for WR line

lcd_clock_source_t clk_src

Clock source for the I80 LCD peripheral

int data_gpio_nums[ESP_LCD_I80_BUS_WIDTH_MAX]

GPIOs used for data lines

size_t bus_width

Number of data lines, 8 or 16

size_t max_transfer_bytes

Maximum transfer size, this determines the length of internal DMA link

size_t psram_trans_align

DMA transfer alignment for data allocated from PSRAM

size_t dma_burst_size

DMA burst size, in bytes

size_t sram_trans_align

DMA transfer alignment for data allocated from SRAM

struct esp_lcd_panel_io_i80_config_t

Panel IO configuration structure, for intel 8080 interface.

Public Members

int cs_gpio_num

GPIO used for CS line, set to -1 will declaim exclusively use of I80 bus

uint32_t pclk_hz

Frequency of pixel clock

size_t trans_queue_depth

Transaction queue size, larger queue, higher throughput

esp_lcd_panel_io_color_trans_done_cb_t on_color_trans_done

Callback invoked when color data was transferred done

void *user_ctx

User private data, passed directly to on_color_trans_done's user_ctx

int lcd_cmd_bits

Bit-width of LCD command

int lcd_param_bits

Bit-width of LCD parameter

unsigned int dc_idle_level

Level of DC line in IDLE phase

unsigned int dc_cmd_level

Level of DC line in CMD phase

unsigned int dc_dummy_level

Level of DC line in DUMMY phase

unsigned int dc_data_level

Level of DC line in DATA phase

struct esp_lcd_panel_io_i80_config_t::[anonymous] dc_levels

Each i80 device might have its own D/C control logic

unsigned int cs_active_high

If set, a high level of CS line will select the device, otherwise, CS line is low level active

unsigned int reverse_color_bits

Reverse the data bits, D[N:0] -> D[0:N]

unsigned int swap_color_bytes

Swap adjacent two color bytes

unsigned int pclk_active_neg

The display will write data lines when there's a falling edge on WR signal (a.k.a the PCLK)

unsigned int pclk_idle_low

The WR signal (a.k.a the PCLK) stays at low level in IDLE phase

struct esp_lcd_panel_io_i80_config_t::[anonymous] flags

Panel IO config flags

Macros

ESP_LCD_I80_BUS_WIDTH_MAX

Maximum width of I80 bus

Type Definitions

typedef struct esp_lcd_i80_bus_t *esp_lcd_i80_bus_handle_t

Type of LCD intel 8080 bus handle


此文档对您有帮助吗?