SDMMC 主机驱动

概述

ESP32-S3 的 SDMMC 主机外设共有两个卡槽，用于插入 SD 卡、连接 SDIO 设备或连接 eMMC 芯片，每个卡槽均可单独使用。

卡槽 SDMMC_HOST_SLOT_0 和 SDMMC_HOST_SLOT_1 都支持 1、4、8 线的 SD 接口，这些卡槽通过 GPIO 交换矩阵连接到 ESP32-S3 的 GPIO，即每个 SD 卡信号都可以使用任意 GPIO 连接。

支持的速率模式

SDMMC 主机驱动支持以下速率模式：

默认速率 (20 MHz)：对于 SD 卡，支持 1 线或 4 线传输；对于 3.3 V eMMC，支持 1 线、4 线或 8 线传输。
高速模式 (40 MHz)：对于 SD 卡，支持 1 线或 4 线传输；对于 3.3 V eMMC，支持 1 线、4 线或 8 线传输。
高速 DDR 模式 (40 MHz)：对于 3.3 V eMMC，支持 4 线传输。

当前尚不支持的速率模式：

高速 DDR 模式：不支持 8 线 eMMC 传输

使用 SDMMC 主机驱动

在大多数应用程序中，只有下列函数会被直接调用：

sdmmc_host_init()
sdmmc_host_init_slot()
sdmmc_host_deinit()

其他函数将通过 sdmmc_host_t 结构体中的函数指针由 SD/MMC 协议层调用，例如：

sdmmc_host_set_bus_width()
sdmmc_host_set_card_clk()
sdmmc_host_do_transaction()

配置总线宽度和频率

使用 sdmmc_host_t 和 sdmmc_slot_config_t 的默认初始化配置，即 SDMMC_HOST_DEFAULT 和 SDMMC_SLOT_CONFIG_DEFAULT 时，SDMMC 主机驱动会尝试以当前卡所支持的最大总线宽度进行通信（SD 卡为 4 线，eMMC 为 8 线），并使用 20 MHz 的通信频率。

在支持 40 MHz 频率通信的设计中，可以调整 sdmmc_host_t 结构体中的 max_freq_khz 字段，提升总线频率：

sdmmc_host_t host = SDMMC_HOST_DEFAULT();
host.max_freq_khz = SDMMC_FREQ_HIGHSPEED;

如需选择标准速率以外的特定频率，请根据所使用的 SD 接口（SDMMC 或 SDSPI）确定适当频率范围，并选择其中的任意值。然而，实际的时钟频率会由底层驱动程序计算，可能与你所需的值不同。

使用 SDMMC 接口时，max_freq_khz 即频率上限，因此最终的频率值应始终低于或等于该上限。而使用 SDSPI 接口时，驱动程序会提供最接近的适配频率，因此该值可以大于、等于或小于 max_freq_khz。

请配置 sdmmc_slot_config_t 的 width 字段，配置总线宽度。例如，配置 1 线模式的代码如下：

sdmmc_slot_config_t slot = SDMMC_SLOT_CONFIG_DEFAULT();
slot.width = 1;

配置 GPIO

通过配置结构体 sdmmc_slot_config_t，ESP32-S3 的 SDMMC 主机可以根据需要，为每个信号配置任意的 GPIO 管脚。

例如，使用以下代码，可以将 GPIO 1-6 分别用于 CLK、CMD、D0-D3 信号：

sdmmc_slot_config_t slot = SDMMC_SLOT_CONFIG_DEFAULT();
slot.clk = GPIO_NUM_1;
slot.cmd = GPIO_NUM_2;
slot.d0 = GPIO_NUM_3;
slot.d1 = GPIO_NUM_4;
slot.d2 = GPIO_NUM_5;
slot.d3 = GPIO_NUM_6;

也可以配置 CD 和 WP 管脚。与配置其他信号的方法类似，你只需配置相同结构体的 cd 和 wp 参数：

slot.cd = GPIO_NUM_7;
slot.wp = GPIO_NUM_8;

SDMMC_SLOT_CONFIG_DEFAULT 将 CD 和 WP 管脚都配置为 GPIO_NUM_NC，表明默认情况下不会使用这两个管脚。

通过上述方式初始化 sdmmc_slot_config_t 结构体后，即可在调用 sdmmc_host_init_slot() 或其他任意高层函数（如 esp_vfs_fat_sdmmc_mount()）时使用该结构体。

eMMC 芯片的 DDR 模式

默认情况下，如果满足以下条件，将使用 DDR 模式：

在 sdmmc_host_t 结构体中将 SDMMC 主机频率配置为 SDMMC_FREQ_HIGHSPEED，且
eMMC 芯片在其 CSD 寄存器中报告支持 DDR 模式

DDR 模式对信号完整性要求更高。如果要在保持 SDMMC_FREQ_HIGHSPEED 频率的同时禁用 DDR 模式，请在 sdmmc_host_t 结构体的 sdmmc_host_t::flags 字段中清除 SDMMC_HOST_FLAG_DDR 位：

sdmmc_host_t host = SDMMC_HOST_DEFAULT();
host.max_freq_khz = SDMMC_FREQ_HIGHSPEED;
host.flags &= ~SDMMC_HOST_FLAG_DDR;

API 参考

Header File

components/esp_driver_sdmmc/include/driver/sdmmc_host.h
This header file can be included with:
#include "driver/sdmmc_host.h"
This header file is a part of the API provided by the esp_driver_sdmmc component. To declare that your component depends on esp_driver_sdmmc, add the following to your CMakeLists.txt:
REQUIRES esp_driver_sdmmc
or
PRIV_REQUIRES esp_driver_sdmmc

Functions

esp_err_t sdmmc_host_init(void)

Initialize SDMMC host peripheral.

备注

This function is not thread safe

返回

ESP_OK on success or if sdmmc_host_init was already initialized with this function
ESP_ERR_NO_MEM if memory can not be allocated

esp_err_t sdmmc_host_init_slot(int slot, const sdmmc_slot_config_t *slot_config)

Initialize given slot of SDMMC peripheral.

On the ESP32, SDMMC peripheral has two slots:

Slot 0: 8-bit wide, maps to HS1_* signals in PIN MUX
Slot 1: 4-bit wide, maps to HS2_* signals in PIN MUX

Card detect and write protect signals can be routed to arbitrary GPIOs using GPIO matrix.

备注

This function is not thread safe

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
slot_config -- additional configuration for the slot

返回

ESP_OK on success
ESP_ERR_INVALID_STATE if host has not been initialized using sdmmc_host_init
ESP_ERR_INVALID_ARG if GPIO pins from slot_config are not valid

esp_err_t sdmmc_host_set_bus_width(int slot, size_t width)

Select bus width to be used for data transfer.

SD/MMC card must be initialized prior to this command, and a command to set bus width has to be sent to the card (e.g. SD_APP_SET_BUS_WIDTH)

备注

This function is not thread safe

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
width -- bus width (1, 4, or 8 for slot 0; 1 or 4 for slot 1)

返回

ESP_OK on success
ESP_ERR_INVALID_ARG if slot number or width is not valid

size_t sdmmc_host_get_slot_width(int slot)

Get bus width configured in sdmmc_host_init_slot to be used for data transfer.

参数: slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
返回: configured bus width of the specified slot.

esp_err_t sdmmc_host_set_card_clk(int slot, uint32_t freq_khz)

Set card clock frequency.

Currently only integer fractions of 40MHz clock can be used. For High Speed cards, 40MHz can be used. For Default Speed cards, 20MHz can be used.

备注

This function is not thread safe

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
freq_khz -- card clock frequency, in kHz

返回

ESP_OK on success
other error codes may be returned in the future

esp_err_t sdmmc_host_set_bus_ddr_mode(int slot, bool ddr_enabled)

Enable or disable DDR mode of SD interface.

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
ddr_enabled -- enable or disable DDR mode

返回

ESP_OK on success
ESP_ERR_NOT_SUPPORTED if DDR mode is not supported on this slot

esp_err_t sdmmc_host_set_cclk_always_on(int slot, bool cclk_always_on)

Enable or disable always-on card clock When cclk_always_on is false, the host controller is allowed to shut down the card clock between the commands. When cclk_always_on is true, the clock is generated even if no command is in progress.

参数

slot -- slot number
cclk_always_on -- enable or disable always-on clock

返回

ESP_OK on success
ESP_ERR_INVALID_ARG if the slot number is invalid

esp_err_t sdmmc_host_do_transaction(int slot, sdmmc_command_t *cmdinfo)

Send command to the card and get response.

This function returns when command is sent and response is received, or data is transferred, or timeout occurs.

Attention: Data buffer passed in cmdinfo->data must be in DMA capable memory and aligned to 4 byte boundary. If it's behind the cache, both cmdinfo->data and cmdinfo->buflen need to be aligned to cache line boundary.

备注

This function is not thread safe w.r.t. init/deinit functions, and bus width/clock speed configuration functions. Multiple tasks can call sdmmc_host_do_transaction as long as other sdmmc_host_* functions are not called.

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
cmdinfo -- pointer to structure describing command and data to transfer

返回

ESP_OK on success
ESP_ERR_TIMEOUT if response or data transfer has timed out
ESP_ERR_INVALID_CRC if response or data transfer CRC check has failed
ESP_ERR_INVALID_RESPONSE if the card has sent an invalid response
ESP_ERR_INVALID_SIZE if the size of data transfer is not valid in SD protocol
ESP_ERR_INVALID_ARG if the data buffer is not in DMA capable memory

esp_err_t sdmmc_host_io_int_enable(int slot)

Enable IO interrupts.

This function configures the host to accept SDIO interrupts.

参数: slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
返回: returns ESP_OK, other errors possible in the future

esp_err_t sdmmc_host_io_int_wait(int slot, TickType_t timeout_ticks)

Block until an SDIO interrupt is received, or timeout occurs.

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
timeout_ticks -- number of RTOS ticks to wait for the interrupt

返回

ESP_OK on success (interrupt received)
ESP_ERR_TIMEOUT if the interrupt did not occur within timeout_ticks

esp_err_t sdmmc_host_deinit_slot(int slot)

Disable SDMMC host and release allocated resources gracefully.

备注

If there are more than 1 active slots, this function will just decrease the reference count and won't actually disable the host until the last slot is disabled

备注

This function is not thread safe

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)

返回

ESP_OK on success
ESP_ERR_INVALID_STATE if SDMMC host has not been initialized
ESP_ERR_INVALID_ARG if invalid slot number is used

esp_err_t sdmmc_host_deinit(void)

Disable SDMMC host and release allocated resources forcefully.

备注

This function will deinitialize the host immediately, regardless of the number of active slots

备注

This function is not thread safe

返回

ESP_OK on success
ESP_ERR_INVALID_STATE if SDMMC host has not been initialized

esp_err_t sdmmc_host_get_real_freq(int slot, int *real_freq_khz)

Provides a real frequency used for an SD card installed on specific slot of SD/MMC host controller.

This function calculates real working frequency given by current SD/MMC host controller setup for required slot: it reads associated host and card dividers from corresponding SDMMC registers, calculates respective frequency and stores the value into the 'real_freq_khz' parameter

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
real_freq_khz -- [out] output parameter for the result frequency (in kHz)

返回

ESP_OK on success
ESP_ERR_INVALID_ARG on real_freq_khz == NULL or invalid slot number used

esp_err_t sdmmc_host_set_input_delay(int slot, sdmmc_delay_phase_t delay_phase)

set input delay

This API sets delay when the SDMMC Host samples the signal from the SD Slave.
This API will check if the given delay_phase is valid or not.
This API will print out the delay time, in picosecond (ps)

备注

ESP32 doesn't support this feature, you will get an ESP_ERR_NOT_SUPPORTED

参数

slot -- slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
delay_phase -- delay phase, this API will convert the phase into picoseconds and print it out

返回

ESP_OK: ON success.
ESP_ERR_INVALID_ARG: Invalid argument.
ESP_ERR_NOT_SUPPORTED: ESP32 doesn't support this feature.

esp_err_t sdmmc_host_get_dma_info(int slot, esp_dma_mem_info_t *dma_mem_info)

Get the DMA memory information for the host driver.

参数

slot -- [in] slot number (SDMMC_HOST_SLOT_0 or SDMMC_HOST_SLOT_1)
dma_mem_info -- [out] DMA memory information structure

返回

ESP_OK: ON success.
ESP_ERR_INVALID_ARG: Invalid argument.

esp_err_t sdmmc_host_is_slot_set_to_uhs1(int slot, bool *is_uhs1)

Check if the slot is set to uhs1 or not.

参数

slot -- [in] Slot id
is_uhs1 -- [out] Is uhs1 or not

返回

ESP_OK: on success
ESP_ERR_INVALID_STATE: driver not in correct state

esp_err_t sdmmc_host_get_state(sdmmc_host_state_t *state)

Get the state of SDMMC host.

参数

state -- [out] output parameter for SDMMC host state structure

返回

ESP_OK on success
ESP_ERR_INVALID_ARG on invalid argument

Structures

struct sdmmc_slot_config_t

Extra configuration for SDMMC peripheral slot

Public Members

gpio_num_t clk: GPIO number of CLK signal.

gpio_num_t cmd: GPIO number of CMD signal.

gpio_num_t d0: GPIO number of D0 signal.

gpio_num_t d1: GPIO number of D1 signal.

gpio_num_t d2: GPIO number of D2 signal.

gpio_num_t d3: GPIO number of D3 signal.

gpio_num_t d4: GPIO number of D4 signal. Ignored in 1- or 4- line mode.

gpio_num_t d5: GPIO number of D5 signal. Ignored in 1- or 4- line mode.

gpio_num_t d6: GPIO number of D6 signal. Ignored in 1- or 4- line mode.

gpio_num_t d7: GPIO number of D7 signal. Ignored in 1- or 4- line mode.

gpio_num_t gpio_cd: GPIO number of card detect signal.

gpio_num_t cd: GPIO number of card detect signal; shorter name.

gpio_num_t gpio_wp: GPIO number of write protect signal.

gpio_num_t wp: GPIO number of write protect signal; shorter name.

uint8_t width: Bus width used by the slot (might be less than the max width supported)

uint32_t flags: Features used by this slot.

struct sdmmc_host_state_t

SD/MMC host state structure

Public Members

bool host_initialized: Whether the host is initialized.

int num_of_init_slots: Number of initialized slots.

Macros

SDMMC_SLOT_FLAG_INTERNAL_PULLUP: Enable internal pullups on enabled pins. The internal pullups are insufficient however, please make sure external pullups are connected on the bus. This is for debug / example purpose only.

SDMMC_SLOT_FLAG_WP_ACTIVE_HIGH: GPIO write protect polarity. 0 means "active low", i.e. card is protected when the GPIO is low; 1 means "active high", i.e. card is protected when GPIO is high.

SDMMC_SLOT_FLAG_UHS1: Enable UHS-I mode for this slot

此文档对您有帮助吗？

反馈已收到，谢谢！
如果您有其他意见，欢迎填写乐鑫文档反馈表。

我们重视您的反馈。
您可以填写乐鑫文档反馈表告诉我们如何改进该文档。

SDMMC 主机驱动

概述

支持的速率模式

使用 SDMMC 主机驱动

配置总线宽度和频率

配置 GPIO

eMMC 芯片的 DDR 模式

相关文档

API 参考

Header File

Functions

Structures

Macros